Reviews
For crafts
Purchased to secure aluminum plate when cutting out and drilling holes
It is working as expected.
View detail
Convenient to have
It can also measure depth, which is very useful to have.
The movement is a little stiff, but I think it is appropriate for the price.
View detail
Ordinary Socket
One day I looked at the Socket set and found that the 10mm was missing, which I assumed was lost because it was used so frequently.
I purchased the SK-11 as my first choice.
It came out of the tool box after purchase. I don't care how many I have, I will use it as a Socket for Touring's tools.
View detail
Tools used only occasionally are SK11
I use basic KTC and Tone for tools.
I use SK11 for tools that are used only occasionally.
Insert angle of this Deep socket:6.35mm (1/4Inch) Purchase
Sprocket Coveretc.It is necessary to remove the bolt that is deep in the bolt, and it is necessary to remove the bolt that is deep in the bolt.
Frequently used insertion angle:9.5mm (3/8Inch) Deep socket in the
If you try to use the 8mm, the Ratchet Pouch opening will be
It's thicker, so it hits the Cover.
So, insertion angle:6.35mm (1/4Inch) will be needed
But I don't use KTCetc. so I don't want to buy KTCetc. for my Wallet...
Thank goodness for SK11's Socket
Reliable quality at a reasonable price
I use KTC and Tone where I hang Large Torque.
The parts of SmallTorque that are not used much are supplemented with SK11.
View detail
Drumstickn, Drumstickn!
I often make my own parts for ZEPHYR400 and CUB90. I often use Aluminum plate as material.
For the cutout, we used different tools depending on the thickness:Gold scissors tend to bend the object while cutting, and an iron saw tends to blur the cutting line. It took a lot of time and effort to make the final correction and polish it to make it less noticeable.
I had never seen SK-11's Hand nibbler tool in person, so I did not have an Image to use it. I had never seen a hand nibbler before, so I did not have an image of using it. I purchased it and found it easy to use, and I enjoyed cutting aluminum and steel plates. It is not like cutting with a normal scissors, but with a drumstick, a drumstick, a drumstick.
The blade is a sturdy Square Type with a thickness of approximately 6mm. The blade is clamped between the blade and the board, and the blade moves down and cuts off the board in one grip. The grip force varies depending on the material and thickness to be cut; even aluminum plates are quite tiring. It is easier to cut by gripping the blade or placing the lower side of the fixed grip against the flat surface of the worktable and pushing the working grip in with your arm strength.
I had a person with a weak grip use it; he could not cut a 1mm Aluminum board with one grip. I think it has something to do with the strength. I'm afraid that if I force myself to grip it too tight, I'll hurt my fingernails." I was told. I could use a leather hand, but it is dangerous and difficult to slip.
Because of the thickness of the blade, the cut will drop about 6mm worth of cuttings. In the case of an iron saw, it will be about 2mm worth of iron dust. It is better to use different tools considering the labor and the processing time after cutting.
The blade bite was good when new, but the blade is starting to round off a bit. It would be nice to replace or polish the blade, but since it is inexpensive, it may be a good idea to replace it.
If you want to make longer cuts, you can choose an electric saw. However, for small workpieces, SK-11's Hand nibbler is sufficient.
View detail
Easy to use
Purchased for Small TypeRatchet, cost performance is high with Holder set. Easy to use even in tight spaces. View detail
Purchased for Torque wrench
Purchased for Torque wrench. However, the Holder cracked rather easily if I didn't pinch it properly. View detail
Torque also has a Quantity:Set is convenient
I wanted a Torque set and found the other SK11Socket easy to use, so I bought this one. View detail
Small Water Resistant Paper 100pcs.
Large size is easy to work with, even for small scratches!
Outclassing is a pre-treatment for Motorcycle Cowl before painting!
This Quantity:Set has made a lot of progress in preprocessing!
I would like to buy again.
Thank you for the Large change!
View detail
Great tweezers
Love these so far. They are a great build quality that feels sturdy in the hand.Works great and made from metal so it's more environmental and sustainable material. Pleased I avoid buying another plastic tool.definitely recommend View detail
A good tool that helps save time
I bought this socket handle again. It takes up very little space in the tool bag. I just put the sockets in my toolbox. It takes up very little space. It is very useful and ergonomic. It is very easy and fast to use.Depending on the job, this can be easier and quicker than getting a ratchet and extension. There is nothing like it in terms of design. Japanese hand tools are unique in terms of design and quality.I'm glad I have it,definitely recommended View detail
Used to remove the Clutch of LETS4Palette
When removing the clutch outer of the LETS4Palette, the nut holding the clutch outer in place was used to loosen it.
I was able to loosen a nut that did not loosen at all with the 150~180mmRatchet wrench I usually use.
Because of its long overall length, it is a convenient tool that can be used to apply large torques even by human power.
View detail
A must have tool for any tool box.
This tool comes in handy for all my little jobs and some big ones.The depth of insertion of the socket allows the optional setting of fixed and pivoting.it can be used as an extension bar.It is pretty sturdy and well made.The Japanese quality shines through, the feel in the hand is incredible. It's quick to use the handle is large enough to get a good amount of torque on the screw or nut being tightened. so far the tool has been very durable and not let me down while being used. View detail
I think it is very cosy. It is carefully made.
I have been using Quantity for many years now.:The socket adapter of the set finally broke. I was looking for a replacement, and this product seemed to be the cheapest and the most well-made, so I bought it. I bought it because it seemed to be the cheapest and well-made product I could find. It fits very snugly and is easy to remove, and I think it is very cost effective.
I don't know about durability, but it looks good, so I gave it 5 stars.
View detail
Suitable for portable, not stationary
Purchased to adjust air pressure at Circuit.
Since the capacity is small, filling a single tire is not efficient because the air runs out. TradeOff is unavoidable if the limited loading space is to be used effectively.
It is not a quiet Type and is not suitable for home use.
The 100V power supply type is perfect for use as a portable Small Type Compressor with a generator.
Other negatives are reasonable considering the price and Size.
View detail
Aluminum Pipe is looking sharp.
I bought a long aluminum pipe for my own parts for CRF250RALLY. I used to cut it with an iron saw, but I think it is better to use SK11's Pipe cutter for clean cutting.
After deciding the length to be cut, use the Magic to mark a point on the Pipe cutter, place the round blade of the Pipe cutter on the point, and lightly tighten the Grip. When the markings are visible, turn the Pipe cutter further. You will feel resistance when you turn it, but when it becomes weaker, the amount of turning will be cut. If you continue to rotate the Pipe cutter, the Pipe cutter will make a horizontal gap, so you will need to increase the depth of the cut by pulling out the round blade further. After cutting, pull out the chamfering blade attached to the body to chamfer the inside of the pipe.
When determining the length of the cut, it is better to make adjustments by considering the thickness of the blade. In the case of an iron saw, the object is cut off with the tip of the blade on a line Image, but with a round blade, Quantity:Pair (for Left and Right) The body has a roller to hold the pipe in place. The body has a roller to hold the pipe in place. If the object is soft aluminum, the roller will leave marks if it is tightened too hard. If the holder of the round blade starts to wobble during use, which is rare, remove the grip cover and tighten the loose screws. The first marking is easy with aluminum, but difficult with steel, and be careful with plating pipe, which is slippery even after marking. The chamfering after the work is simple. The final chamfering should be done with sandpaper or a file or you will get hurt.
This tool is designed for Pipe, but I also use it for cutting and marking aluminum rods with an iron saw. The process is the same, but there is a limit to how far a round blade can cut a round bar. If the marking is on a line, it is easier to apply the cutting edge of the iron saw and fix it in place. In this case, the length of the cut is adjusted with a margin for the tip of the blade.
If you are a beginner, it is difficult to cut a round Pipe cleanly with an iron saw. It depends on the work environment, but it is a good tool to have.
View detail
There are three mouths.
Snap rings are often used to hold down the Kick Arm axis of a moped scooter.
LargeIn the past, I used radio pliers and pick tools as substitutes. It was still inconvenient, though it was usable for the time being, and it took a lot of time and effort to remove the Ring by holding it down and almost scratching the Aluminum case.
My senior recommended me to buy a dedicated pliers and I used it for many years, but the tip of the mouth broke off and I could no longer use it. Once you know the taste of dedicated tools, you can't stand the inconvenience. The last time I used this type, I had to replace the mouth, but the target was not always the same snap ring, and I didn't want to go through the trouble of finding a different mouth each time, so this time I bought SK11's one type with three mouths. It takes up more space in the tool box, but in terms of total area, it is no different from the mouth-changing type. It can't be used in deep places, but I don't plan to use it for anything other than my Dio, so that's not a problem. It is a tool that I don't use very often, but the price is not as high as before. If I need another type, I can buy it again.
After all, Snap ring is not something to work with a substitute tool. We also felt that just using this tool would save time.
View detail
Used to secure Plate to repainted Frame
I bought a battered 900SS (900SL) and am Restore.
For the frames with noticeable rust, I had originally planned to remove the rust by rubbing the paint off with a wire brush, and then finish with a two-component urethane can spray from DAYTONA, Soft99, or Okitsumo.
However, when I rubbed the slightly rusted area...I found that the rust was progressing like a worm crawling under the paint film.
We had no choice but to strip off all the paint, but then the problem would be the MODELPlate that is Rivet-fastened to the frame.
It is clear that the display printed on the Plate would also peel off if the Plate is left as it is, so the Plate was removed before the paint was peeled off.
After stripping the paint, removing the rust with sandblast, and powder coating (we gave up on the two-component urethane can spray finish because the rust in the intricate areas was too severe to remove with a wire brush), the Plate must now be mounted on the Frame. I gave up on the two-component Urethane can Spray finish.
This Rivet was used in that case.
There is no particular element that says, "This is the only Rivet! It is a very ordinary Rivet.
Aluminum Flange、Stainless shaft。
I could have purchased it separately at Home center, but it would have been a hassle to go and buy it, and I bought Rivet along with my other purchases.
There is no absolute necessity to buy at Webig, but it is convenient to be able to buy small items such as these all at once.
These ultra-fine Size Rivets are I went to the home center and it wasn't there. What a frequent occurrence....
It may be a little cheaper if you buy from a specialty store like Monota0u, but if you consider the shipping cost and the hassle of having it delivered by RoseRose, it is more economical to buy from WeBig for a small price difference.
And there's no way I'd buy just this one.
The feeling of using the Rivet is very normal, so there is nothing special to say.
If I may say so, it is better to prepare a bag with a zipper if you do not plan to use it up, because it is not designed to be stored when the Package is opened (it is just a Blister pack).
View detail
Just in case when painting.
[How is it used?
EachParts is painted with Can Spray or other paint for TZr50RRestore.
In doing so, I found that there were quite a few paint particles flying around, which I did not notice at first.
I wear glasses on a daily basis, but I bought these to protect my eyes as well since Lens became a little safer and shinier.
Was the one you received as per Image?
It was just as Image.
It was solid like science experiment Glasses.
How was your experience with it?
I am concerned about the pressure until I get used to it, but I need it for my health, so I have to be patient there.
[Points to note]
It is quite difficult to see when it gets dark, so that's where Neck is.
How did it compare to other products?
It is more reliable protection than ordinary Glasses.
View detail
This is enough for the Torx bit socket of T30
[How is it used?
Used to remove the key cylinder from the Top Bridge of a YAMAHA TZr50R.
I had TorqueT40 for XJR400R Rear suspension, but the size was different, so I had to purchase additional TorqueT40 as Single Item.
Was the one you received as per Image?
It was just as Image.
I checked the size in Home center before purchasing.
How was your experience with it?
It works fine. SK11 is very good for DIY riders because of its cost performance.
[Points to note]
Not particularly
How did it compare to other products?
Torque is rarely used on domestic cars, so I think that SK11's most cost-effective tools will be enough without buying expensive ones.
View detail