Reviews
No durability
The quality of Rubber is poor and cracks immediately after 6 months. View detail
It was replaced at the same time when 88Bore up, but it cannot be tightened subtlyQuantity:Set item
Used when assembling DAYTONA's 88Kit on SUPER CUB.
Since the cylinder stud bolt tends to loosen easily, I have been using a reinforced stud that can be used with a long nut for a long time. However, since the DAYTONA reinforced stud that I love is no longer available, I chose this one.
After assembly and test run, oil leaked from the head and base gasket. After re-checking, there was no problem, and retightening was done again and again, but to no avail.
I looked at the amount of screw threads coming out of the head cover and the long nut that came with it and noticed that there was not much difference in length. I found a used reinforced with stud nut that was slightly longer than the cap nut, and tightened it at the specified torque!
I don't know if it is an individual difference or a difference in the manufacturer, but the Quantity:The set product Nut could not be tightened sufficiently.
By the way, Stud itself has no problems.
View detail
Six months of life expectancy with daily use
Used with PE24 on a commuter vehicle. I think half a year of life is too short even though it is used as a manifold for air duct of Mukawa and some bending force is applied to it. I don't know if there is a durability problem in the material of the rubber used or if it is an individual difference. For the time being, let's use it as a Race part. View detail
I'll take DAYTONA for this one.
[How is it used?
I chose this as my LITTLE CUB's Throwk Up companion.
Was the one you received as per Image?
Package is normal. The product itself is also Pad look clean.
Was the installation difficult?
How was your experience with it?
This was a problem.
I removed the original stud bolt and inserted it, but it was hard to turn.
If you are wondering why, the coating on this Stud bolt itself is interfering with the threads a bit.
Thanks to this, I had to re-cut the threads firmly beforehand, or straighten them with Nut, which is not important.
You could destroy the Engine if you didn't know you were busting it.
But other than that it's good. By the way, it's the same when I try it with a different Bolt or below the waist, so I don't believe it's a skill issue. I want to believe.
The thickness is also thicker than OEM and the cosmetics are not bad.
It was a bit advanced.
[Included Parts:were they on?
It has a Cap-like Bolt.
This one also eats up the screw thread problem, so you want to make sure you handle it properly.
[Was there anything that disappointed you?
Screw thread. Anyway, screw thread.
Although the price is higher, DAYTONA's Reinforced Stud is a more solid product.
View detail
It didn't help.
When I fell over, it tore off and flew off, leaving the part that was tightened up by the Bolt. The part that was torn off was not damaged so much, and I think that it flew away before it did not play a role in damage-reduction very much. View detail
Fits: HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey, HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey
You were so good last time.
I had no problems with the Stud bolt replacement on my previous Super CUB 50.
But this time, the bolt was twisted while I was tightening one of them. Material is not good. After all, I got rid of it. I bought the material at Homsen.:Stainless Steel bolts were machined and installed.
View detail
Fits: HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey, HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey
Only the bolts no studs..
Am I the only one that thought there would be also flange nuts included in this kit? Was a waste of money obviously.. Also for most Honda models 6x35 is more suitable.. View detail
It is good when new - - -
KITACO's VM 26 Manifold is used for Ape 100
Keihin PE 26 is installed.
Because KITACO's RubberInsulator has failed
Purchased as for Repair.
When it is brand new, there is no problem
Secondary air generation occurred after 2 years ago,
Quantity : 2pc. I purchased a set of eyes.
A bit more durable Does anything matter?
I appreciate that there are such Repair Parts.
View detail
Fits: HONDA NSF100, HONDA NSR Mini, HONDA NSF100, HONDA NSR Mini
Purchase to make NSF Positive Change
Looking after installation is good Large change.
However, footpeg broke in SlipDown and flew away, Plate was also distorted, rebounded to ROD and could not start again.
It is weak in terms of strength.
I will exchange it for another footpeg.
View detail
It will immediately expire as evaluated by others
Other people have also written, but it was short soon.
It did not last six months.
There is no meaning if it is cheap or bad.
Is it a consumable item that is not severe?
View detail
It was a favorite
Blinker's contact is bad
If you are investigating the cause
I noticed it was broken.
Material : Sorry it was because I liked Aluminum.
Is the cause of the crack vibration?
View detail
It purchased because collecting-pipe wearing can also respond. Although it is used for z1, the wheel is offset by the left, and since the place which can carry out a jack-up is pinpoint, z1 is touch that it can be well used just before. If it is r
It purchased because collecting-pipe wearing can also respond.
Although it is used for z1, the wheel is offset by the left, and since the place which can carry out a jack-up is pinpoint, z1 is touch that it can be well used just before.
If it is removed, it will hit a collecting pipe, or it becomes a location which is equivalent to the sprocket nut of a wheel and a wheel cannot rotate.
Or [ being just going to say that it is unavoidable as it can use well ] ..
View detail
Fits: HONDA NSF100, HONDA XR100 Motard, HONDA XR50 Motard, HONDA Ape 100, HONDA Ape 50, HONDA NSF100, HONDA XR100 Motard, HONDA XR50 Motard, HONDA Ape 100, HONDA Ape 50
It attached together with the oil shower head of the company. Since the nipple of an 8-mm hose is high at M10, I think with a hose that this price is cheap. However, the die length of a hose is lacking even to the oil catch tank which I have attac
It attached together with the oil shower head of the company.
Since the nipple of an 8-mm hose is high at M10, I think with a hose that this price is cheap.
However, the die length of a hose is lacking even to the oil catch tank which I have attached, and I will consider it as this evaluation.
Moreover, I would like you to use a 6-mm hose by M8 safely.
View detail