Reviews
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA CHALY 50, HONDA CD50, HONDA BENLY50S, HONDA CL50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA CUB press 50, HONDA CUB press 50, HONDA CUB press 50, HONDA CUB press 50, HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA MONKEY BAJA
Required if Bore up.
When the engine displacement volume is increased by bore-up, the scale of explosion becomes larger than that of the OEM, and the oil pump designed for 50cc of the OEM cannot keep up with the oil circulation. Therefore, we introduced the Reinforced Oil Pump.
[Oil pump's role].
The oil pump pressurizes and pumps the engine oil to circulate it to the various parts of the engine. 。 This enhances lubrication, cooling and cleaning effects.
[What happens due to lack of Oil circulation.
→ oil film breakdown and increased oil temperature.
The oil pump sucks up engine oil that has accumulated below the waist and circulates it above the waist. (The oil then flows back into the lower back to continue circulation.) Cylinder Cylinder head Camshaft Piston Therefore, if the oil cannot circulate properly, there is a possibility that these parts will break. To explain this in a simple way, if the oil film on the parts runs out, the parts will be damaged and the oil will be lost. [Burns in] it appears as if ... 。 Naturally, parts that are seized are unusable and must be reassembled.
Effects of Reinforced Oil Pumps
Circulation of the proper amount of oil reduces the burden on the parts of the drive unit. 。 Also, by increasing the Engine Displacement Volume, a larger volume of oil can be circulated to the engine, which generates more heat and thus cools the engine even more.
*OEM oil pumps are designed for OEM for 50cc, so if you bore up, you will have to reconfigure the oil pump with an enhanced (higher discharge) oil pump to match, or the oil will not be circulated in time.
This Oil pump has a capacity = amount of Oil to send 。 If OEM Product is diverted, the capacity will be as follows : Assuming that 50cc is 1.0, it is about 1.8 to 2 times larger.
good point
Heat generation from the Engine after driving has subsided.
Even if you go for a long ride and turn it around a bit, there is no longer any heat drop.
Idling is stable.
A bad point
I also removed the oil, removed the →clutch cover, and replaced the →gasket.
It's worth changing, though (laughs).
When you bore up the engine, it is strongly recommended to install a Reinforced Oil Pump. If you are looking for a domestic manufacturer, SHIFT UP is the cheapest.
If the Bore Up Kit you purchased becomes useless because you were too stingy with the Gold amount, the cost will be large…. 。 Some of you may have assembled the Bore Up Kit with the NORMAL oil pump, but it is not a stingy PARTS, so I recommend not to drink that opinion too much.
If there is room, it would be even more effective if the orifice of the oil coming out of the oil pump is enlarged.
View detail
MJQuantity for Keihin PBcarburetor by SHIFT UP:Set
I used it in the Carburetor setting of the C50SUPER CUB.
Since there are six different types, I was able to find a good spot by changing it out, running, running and changing it back in. I am very happy with the purchase.
View detail
Xr100 with vm26
This manifold is just what I needed to fit a mikuni vm26 on my xr100. It's a high quality part and worth every penny! Will definitely order again! View detail
CUB to Blowby's extraction!
CUB I put it on my Blowby's and took it out. The price and construction are great. I would like to get one more. View detail
SHIFT UP
I like the products of this brand. I'm looking for parts to create a custom look for my Monkey. This product not only has a beautiful appearance, which is combined with other installed elements, but also has functional properties (engine cooling). I had great pleasure working with this part. View detail
To install PWK on CB50
Used to install PWK on CB50.
OEM Side cover will interfere.
View detail
Recommended
Replace while engine overhaul
I don't know about performance w
View detail
Product # 205003-11
Due to the existing need for engine cooling on my HONDA MONKEY after installing a larger cylinder, I was looking for solutions to this problem. One of the options was the use of a lid with cooling fins. A pleasant addition was the presence of a more technological appearance instead of the old, lost-looking lid. The quality is without complaints. View detail
Beautifull finish.
Breather Hose 650mm 6mm Diameter attached at the outlet.
The hose used has an inner diameter of less than 10mm and an outer diameter of a little over 15mm.
It didn't match the Size on the Tag.
I was able to install it properly.
However, it was a little tight when fitting the outer end to the Hose.
After spraying CleanerSpray and pushing hard, I was able to insert it deeper.
It is secured with Hex screws, so there seems to be no worry about it coming off.
View detail
Fits: HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey, HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey
When replacing an external exhaust system
I purchased this bolt because the OEM stud bolt was not long enough when replacing an external exhaust system.
I have driven about 20,000 km since I replaced it and have had no problems.
View detail
Fits: KAWASAKI 500SS Mach III (H1), KAWASAKI 500SS Mach III (H1), KAWASAKI 500SS Mach III (H1), KAWASAKI 750SS MACH III (H2-A), KAWASAKI 750SS MACH III (H2-B), KAWASAKI 750SS MACH III (H2-C), KAWASAKI KH250, KAWASAKI KH400, KAWASAKI KH500, KAWASAKI Z1, KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI 750SS MACH III (H2-A), KAWASAKI 750SS MACH III (H2-B), KAWASAKI 750SS MACH III (H2-C), KAWASAKI KH250, KAWASAKI KH400, KAWASAKI KH500, KAWASAKI Z1, KAWASAKI Z2 (750RS/Z750FOUR)
SHIFT UP Oil Tank Filter Adapter
Reproduct sales will be Large change helpful since OEM Parts are no longer available.
Material of the product is also Material:It is a good product with solid construction of Aluminum with Black Anodized treatment.
View detail
Refreshing、Polished
I like the way the OEMs bend first, but this one has a root bend, so it's easy to kick when you KICK, and then recoil from the KICK to get back to where you started. View detail
Fits: HONDA NSF100, HONDA XR100MOTARD, HONDA XR50 MOTARD, HONDA APE 100, HONDA APE 50
Oil cooler piping
Used as piping for oil cooler.
It is oil-resistant, pressure-resistant, and heat-resistant, making it ideal for oil cooler piping. Its flexibility makes it easy to handle.
View detail
Fits: HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey, HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey
It is a must for Bore up and Overhaul.
I bought this product for my Bore up and it is a reliable manufacturer with good cost performance. View detail
SHIFT UP Mini Breather Filter
About quality and texture - Top Quality. Solid rubber body with perfect sized filter element for an oil catch tank system. About the feeling of use - Firm fit into the Takegawa 8mm breather hose and tucks up nicely out of the way due to being a mini filter. Products to buy together - I have chosen to make this mini breather filter part of my oil catch tank system so if you are looking to also add one of these sytems to your Monkey I'd recommend the ones Takegawa have available which come with almost everything you will need. Difficulty of installation - Simple to install the breather filter, just pushes into the hose and comes with a hose clamp to secure it. Cost performance and comparison with other products - Well priced for a top quality part, no need to look elsewhere. When comparing this filter from Shift Up to one from Uni you will see a massive price difference. About shipping and packaging - I think Webike are doing their best with shipping pricing, so I'm happy. Packages ship within 24 hours and arrive very quickly from Japan. Any concerns, cautions, or advice when purchasing - When I first saw the listing for this part I was unable to locate any dimensions. My photo attached has all the dimensions you will need to help workout if this breather filter will be right for your setup. View detail
Fits: HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey, HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey
Bore up while you're at it!
I bought a bore up kit and replaced it. Now I am going to break it in. View detail
Customized! It will be like that.
I purchased and installed the DAX for the purpose of improving the custom feel of the DAX.
Being a Cut-out, the look, feel, and precision are unquestionable.
O-Ring is used instead of Gasket when removing Camshaft Cover.
I guess it would be a nice Point to not have to replace Gasket.
This is only a custom look and feel, so we do not expect any performance increase.
Also, the price is high, but I think it is reasonable considering the quality and precision.
Just as I thought, the Custom feel is UP to Large width!
View detail
Fits: HONDA NSF100, HONDA XR100MOTARD, HONDA XR50 MOTARD, HONDA APE 100, HONDA APE 50
second purchase
I have bought it once before, and this is the second time. The appearance is absolutely beautiful and the effect is good. This time I bought it for a friend. It is a pity that the black one is still discontinued, and the red one has been discontinued. My two favorite colors are not available. , very unfortunate. View detail
Fits: HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey, HONDA Super Cub 90, HONDA Benly CD90, HONDA monkey
It doesn't have to be double nut.
Speaking of Stud bolt replacement, Double nut is difficult until you get the hang of it (or is it just me?).
This is nice and easy because you can go round and round with Hex.
I like that the price is not so high.
View detail
Fits: HONDA APE100, HONDA APE100 D, HONDA NSF100, HONDA XR100 Motard, HONDA APE100, HONDA APE100 D, HONDA NSF100, HONDA XR100 Motard
makes your bike go!!!
This is one the BEST kits I have ever installed on my motorcycle. It keeps a good balance throughout the powerband and has been very reliable. View detail