Reviews
Durability..
I am using it with Bessler's GoldenPad and the initial bite is thin. I read that the Floating Pin will be replaced at about 3000, but I haven't seen how much it will lose yet.
Really, at 3000, would it be tough to drive around town?
View detail
I installed it.
The center fit was a little looser than OEM, but no problem. 1 hour of use on Circuit, even contact with the pad, no problems. Large sturdy.
The feel of the product is fine.
View detail
for BremboBanjo
For BREMBO Caliper. brembo has Screw Pitch 1.0, so be careful when you buy it. View detail
Complete Diversion
Purchased as a support to put Crab type Brembo on Takekawa's φ27Front fork. From OthersManufacturer, let alone Takekawa. Mukawaφ27for Front ForkCrabCaliper support." One-off is another option, but one-off is quite expensive. The offset to the Fork and Rotor was adjusted by Washer and Shim. The offset to the Fork and Rotor was adjusted by Washer and Shim. View detail
เป็นจานที่คุณภาพสูง สวยงามมาก View detail
ฉันได้นับสินค้าแล้ว ฉันชอบตัวสินค้ามาก ใส่แล้วมำให้รถฉันดูดีมากเลยทีเดียว View detail
Fits: HONDA NSF100, HONDA XR100 Motard, HONDA Ape 100, HONDA NSF100, HONDA XR100 Motard, HONDA Ape 100
no problem
The outer diameter is a little smaller than Active etc., but there is no problem. View detail
Fits: HONDA XR50 Motard, HONDA XR100 Motard, HONDA NSR50, HONDA NSF100, HONDA XR50 Motard, HONDA XR100 Motard, HONDA NSR50, HONDA NSF100
It's not rigid enough.
If you are breaking from the straight end of the circuit, and if you are leaning even a little bit at the entry, the caliper support will creep and you will die from the strong large vibration.
I don't think you'll feel any negatives if you don't have a short cart course in the low 20's or a large speed in town driving.
… Or maybe it's wrong to put Brembo caliper on NSR50 or NSF100 in the first place.
It's my fault that I bought a brembo for my moped Base, not the product.
View detail
Fits: HONDA glom, HONDA NSR mini, HONDA NSF
The consequences of straying
As a result of FBrake hesitation, I'm currently landing here for now.
Biography and Personal Thoughts
Normal caliper + NormalPad... does not work.
Normal caliper + Golden... I'm better now.
Normal caliper+Golden+Mesh hose...a little better, but still unsatisfactory.
Brembo crab + Golden + Mesh hose....
4pod X + attached Pad + Mesh hose + Nisshin Radio Pong (Adapted from GSX-R1000R) ...Fee Ring is improved, and the effect is satisfied somehow.
This is the case
I'd like to go in a more ”Snap” direction, but due to the Small diameter disc, there seems to be a limit.
View detail
Fits: HONDA XR50 Motard, HONDA XR100 Motard, HONDA NSR50, HONDA NSF100, HONDA XR50 Motard, HONDA XR100 Motard, HONDA NSR50, HONDA NSF100
Poor aesthetics
Shift up this brand of products, the price is close to the people, and there are many choices in terms of color, but it is a pity that this product fails in the shape of the product. If you are more beautiful, you can choose the same type of product. View detail
Beautiful and nice
Because the brakes of my xr motard are front and rear discs, I have been struggling to find the same and beautiful discs of the front and rear brands. In the end, only the shift up front and rear spray discs have a variety of colors to choose from and are beautiful in appearance. I am very satisfied View detail
Many colors
The price is a bit expensive, because I use it on XR50 motard, but it has a variety of colors to choose from, which is very satisfactory to me View detail
Fits: HONDA XR50 Motard, HONDA XR100 Motard, HONDA NSR50, HONDA NSF100, HONDA XR50 Motard, HONDA XR100 Motard, HONDA NSR50, HONDA NSF100
Not bad
In terms of price, compared with other products of the same type, this product is relatively cheap, and there are also color choices I like View detail
Fits: HONDA NSF100, HONDA NSR Mini, HONDA XR100 Motard, HONDA XR50 Motard, HONDA Ape 100 Type D, HONDA NSF100, HONDA NSR Mini, HONDA XR100 Motard, HONDA XR50 Motard, HONDA Ape 100 Type D
For the MONKEY bremboCrabNSR50Fork!
i installed this for the bremboCrab caliper device I bought it because the price was cheaper than "G-Cla" and "Takegawa" I was a little worried about the installation, but I could install it without any problem View detail
Fits: HONDA NSF100, HONDA XR100 Motard, HONDA Ape 100, HONDA NSF100, HONDA XR100 Motard, HONDA Ape 100
Large odd, satisfying Parts
I could use an alternative, but I think it's actually a proprietary product, the M10 Aluminum Gasket I used another diverted product, but its thickness was too thick and caused oil leakage And the Oil leak is gone View detail
Performance and looks, enough
I wrote Impressions after receiving the product and before using it
This Impression is an Impression during installation and use
Among the 10,000 to 20,000 dollar Disc Rotor, this one, which is a good cosmetic product, was the right choice for Large!
People say the STD works better or worse, but as far as the 55,000 miles on it, it was fine I think
This time, I can't feel any difference between this product and STD
Compared to the STD, it is better because of its shape, which is expected to help dissipate heat
View detail
This is before I put it on, but it looks like something good
The Front has been replaced and I was looking for a Rear Disc Rotor
Introduced by Design and Cosmo
Installation is in a week, I think
View detail
SHIFT UP 190mm Rear Wave Disc Rotor
great brake disc rotor on performance and looks! i use it on a honda zoomer-x front wheel and it is totally compatible with it. There is no much option for 190mm but this is a great option in desing and performance. View detail
For KSR 2 Caliper support for 210 mm and Brembo crab
I thought whether it was Ikiru to KXCaliper, it was useless to purchase it, contact the Caliper as a result.
I was wondering what to do, knowing Ikel at Brembo crab and 210 mm Support in this review, I was able to install it safely, thank you!
Floating is not a common semi floating but proper? Floating, it is necessary to exchange together the driving situation, it is also nice that Repair Parts comes out.
Although it is not a product of this place, Karatsupo of KKK contacted Pad at the new Crab 34 mm, processing was necessary, Screw Pitch was also weak and Torque could not be applied, so we processed E-sert, well, well Although it seems that there is no schedule of reproductive production due to discontinuation..
It looks good anyway ♪
View detail
MONKEY also disc brake!
Although I was riding in Drum for a while, I raise my heavy back and finally turn it into Disc Brake. I have not seen actual spots, but Front fork, Stem, Caliperetc. I can expect it because it is made in the middle. View detail