Reviews
Causes were easier.
I think the construction of the product is very good.
The installation is of the pinching type and requires a little setting to eliminate gaps.
The cause was easier, but there were times when it was slippery or uncomfortable on Asphalt.
View detail
It's pricey, but I like Earls Gear.
There are many cheap STANDBrackets out there, but I bought this one because it is Earls Gear.
The price is high for what it is, but with the increased stability of the Side Stand and the way it looks, I'm somewhat satisfied!
View detail
Used for diversion
Installed on NINJA Long Side Stand
Installation is no problem, but if it's not a hassle, it's better to weld it one-off tightly.
View detail
Camping touring with full load and expecting to be effective?
I have always felt that the car was leaning too much when stopping at the side stand, so I will be able to use this system in the future Extension to reduce tilt in case of a full load for camping touring installed
I was a little concerned about hanging STAND in places with bad footing and on the shoulder of the road, but as you can see in the photos, I was able to get it to work Balance seems to be a good choice when carrying Large luggage, as it is quite low leaning
It also increases the footprint of the STAND, so it can be used in places where the ground is soft, such as camping grounds You can also expect the STAND to be less likely to be plugged in
As expected of Earls Gear, it has a high quality feel to it
However, there is a part that doesn't fit perfectly with the STAND shape, and the fixed part is slightly floating There is
It seems to be perfectly fine for use, so I'm using it as is
Also, because of the reduced leaning, you have to raise the body of the car more than usual when applying STAND This should be considered a TradeOff
The price is quite high, so I was quite hesitant to buy it, but overall I am very satisfied with the product
View detail
Good design and functionality
When I purchased this product, I bought it on an applicable car and I could not install it well It fit the STANDBracket of the Motorcycle perfectly, but the Bolt is in the back I was only able to stop two of them The first one hit a STANDfootpeg weld and the top cap of the Bracket I purchased The part, per bolt was shaved After completion, it is stopped by two bolts on the back side of two bolts I am worried while running
After installation, the leaning of the Motorcycle has been eliminated
View detail
Things are nice, but …
The thickness of the STAND grounding part and the concave part of Bracket are the same Some of the clasps don't fit, and the clasp floats & hellip;
I raised and lowered the STAND a few times to see if it was loose, and then used it a couple of times and it didn't come loose LargeI think it's sturdy, but if you're worried about it, you might want to get something else
View detail
Fits: BMW F800S, BMW F800R, BMW F800ST, BMW F800S, BMW F800R, BMW F800ST
Although the precision of the work of the product is outstanding ...
It installed in F800ST.
The accuracy of the product's fabrication is wonderful.
On the other hand, the installation Side Stand was for casting? It was decided not to put on a pin but to scrape with File. Also, when paying STAND, the contact surface collapses because it hits Exhaust pipe. (This is also the product of Tulare TEC)
View detail
Recommended for vehicles with no Assist if price is fine
Wr250x does not have Stand Assist and it has difficulty in dropping It purchased and installed a gold tool that is likely to fit at home center but it will rotate with the power of the lowering it will be removed and it will detach in terms of appearance and hesitate in terms of price Although it was finally purchased, 22, 2 Size of Pi is just like to our vehicle and I like the texture of the product well, but even if it is attached directly to the STAND it is necessary to paste Film to prevent large mortgage Considering things, I think that it is good if the Screw mountain part of the bar should be 5 mm longer, but since the part where the Screw is fitted opens a little, when Screw is tightened, the Screw mountain part of the bar is insufficiently tightened If you do not enter the full Bolt part, if you tighten too much, I feel like it will break because M6Size and tighten up to where Body does not move so that Screw will not fall off
Body is wound and fixed with Film. I'd like Manufacturer to improve this neighborhood a bit but the inconvenience that I have had is resolved. In addition, Size is the same as Handlebar 22, 2 pie. If Size is a little thin, I think that we can deal with thin inner Rubber sheet etc, but if it is a little thick Size it will not enter Mounting Hardware For reference.
View detail