Reviews
Fits: HONDA Rebel 1100, HONDA Rebel500, HONDA Rebel250, HONDA Rebel300, HONDA Rebel300
Position will be easier.
After the installation, the position of the handlebar was dramatically improved, especially the upper body became easier. It is easier to install the DAetc. However, when the Handlebar is cut to the full Left position, the gap with the Tank is very small, so I think it is necessary to be careful when attaching attachments around the Handlebar. View detail
Fits: BMW R1200GS, BMW R1200GS Adventure, BMW R1250GS, BMW R1200GS, BMW R1200GS, BMW R1250GS Adventure, BMW R1200GS Adventure
Riding position is now easier.
I used to feel like my arms were stretched all the way out, but after putting this on, I have more room in my arms and the riding position is easier.
I am 167 cm tall.
View detail
Fits: BMW R nineT, BMW R nineT Scrambler, BMW R nineT Pure, BMW R nineT Urban GS, BMW R nineT/5
My arms feel better.
I changed it to NORMAL because with NORMAL, my Right hand gets numb and tired. I chose Earls Gear because of its reliability among various products. I used the same product for R-1200GSA in the past. I did the replacement by myself. It was a good decision because it made driving easier and less tiring. View detail
Fits: BMW R nineT, BMW R nineT Scrambler, BMW R nineT Pure, BMW R nineT Urban GS, BMW R nineT/5
Position is now easier.
The work was done by a Dealer. Work was performed at Dealer.
Until now, I have been using Wonderlich's Spacer to raise it by 20mm,
After changing to this product, positioning became easier.
I have also installed a pull back riser made by r's gear on my previous R1200GS.
I trust the quality of the product because it is made by r's gear.
View detail
Fits: BMW R1200GS, BMW R1200GS Adventure, BMW R1250GS, BMW R1200GS, BMW R1200GS, BMW R1250GS Adventure, BMW R1200GS Adventure
It was the right decision to buy it.
I myself am not tall, so my arms were fully extended in the Normal position.
Touring at high speeds also caused fatigue in the arms and shoulders.
I was a little worried because the parts were quite expensive, but it was the right decision to purchase Large.
After the installation, I immediately went on a day trip of about 500 km for a high speed touring,
There was no fatigue at all from the positions.
It is amazing how much difference it makes even though it only changes its position a few centimeters in front of and above!
This product may be especially recommended for those who are in the early 170cm height range.
The only demerit was that Wiring and Hose are Bolt On, which does not require replacement,
I am worried that the clutch hose will be too tight if the handlebar is cut all the way to the right.
This area may vary from vehicle to vehicle, so I would go to a Motorcycle shop even for an inspection.
I will consult with my mechanic.
View detail
Fits: HONDA Rebel 1100, HONDA Rebel500, HONDA Rebel250, HONDA Rebel300, HONDA Rebel300
MTMODEL×OEMWIN deCowl with high installation difficulty
After much research, I found out that the difficulty level of installing a Handlebar Riser increases dramatically just because it is an MTMODEL Rebel 1100, and it has an OEM cowl, which is even more difficult to install.
As mentioned earlier, the MTMODEL has a patched Clutch Wire, so it is necessary to change the handling to a good one, which increases the difficulty to a degree that you cannot imagine when watching a video of a quick Youtube installation repo with a DCTMODEL.
In addition, in the case of my Motorcycle, because it was equipped with an OEMWIN de Cowl, if this is attached, the Cowl is removed and converted to an Exclusive Bracket, and the difficulty of installing ・・・・ and the Handlebar Riser itself seems to increase dramatically, so I recommend that those who do it on their own are familiar with it and are prepared to install it. Therefore, it is recommended that those who do it by themselves should be prepared to install the Handlebar Riser.
I don't see many repos with this Handlebar Riser in combination with MT×OEMCowl.............................good luck to those who do it by themselves.
Also, the Motorcycle store had to cut out a part of the plastic cover where the clutch wire and other wires are located. If there was no OEM cowl, it might have been possible to handle the wires by just routing the wires, but it seems that the wires could not reach the cowl if it was also attached.
As for the conversion after installation, the conversion was that it did not move backward as much as expected. However, it is still overwhelmingly Quantity in the backward and upward direction.:It is true that the bike is set back, and I can now ride with a hunched posture like when I ride a Harley instead of the leaning forward posture I used to have with my arms pinned and stretched. (However, due to my short arms, my arms remain the same as Pin and taut.) 。
It is pricey, but it is effective, so if you can, you may want to put it on about as soon as you take delivery of the car.
View detail
Optimize Motorcycle's Handlebar position!
I purchased this product because the Handlebar position on the Motorcycle was too far away.
After installing the handlebar, the driving operation became more comfortable due to its proximity to the handlebar.
I am satisfied with the quality and appearance of the Large change.
View detail
Fits: HONDA Rebel 1100, HONDA Rebel500, HONDA Rebel250, HONDA Rebel300, HONDA Rebel300
Ride Attitude Solutions
[How is it used?
I started considering it because I am 169 tall and the Handlebar is a little far away and my upper body gets tight when I ride for long periods of time.
Personally, I think Handlebar is I want to pull it moderately forward, not up." We chose this one because it seemed to best meet our needs.
Was the one you received as per Image?
Texture and cloisonne ware? is satisfactory. It is almost invisible Parts, but …
Was the installation difficult?
I asked N○PS to do it for me. it seems to be a little difficult to handle the Wiring from what I see on YouTube etc. The labor cost was less than 8,000 yen.
How was your experience with it?
I can feel that my riding posture has changed considerably. It has become very comfortable and driving has become even more enjoyable.
I think the price is high, but I am also very satisfied.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
I try not to pay too much attention to it, but it looks quite different, and it's obvious if you don't have the Cowl or Meter visor attached. The front view looks a bit dumb with the distance between the Light and Meter opening up.
If you are concerned, you may need to take action to add Cowl or Visor.
View detail
Fits: BMW R1200GS, BMW R1200GS Adventure, BMW R1250GS, BMW R1200GS, BMW R1200GS, BMW R1250GS Adventure, BMW R1200GS Adventure
Position is now easier.
It is a must have for long distance touring as it has a high quality feel and makes positioning easy. I think it is the best among many similar products. View detail
Update to optimal position.
The best fit like OEMParts, the position is comfortable and the maneuverability has been improved. View detail
Riding Position has improved.
Height 165!
I put this on …ツ-Ring and the pass is good!
View detail
To improve the Riding position
I'm a small guy, so I felt the Handlebar was too far away. I'm a small guy, so the Handlebar seemed a bit far away. It was a good choice for me because it is easy to work with and I can use other brackets and wires as they are. View detail
Fits: HONDA Rebel 1100, HONDA Rebel500, HONDA Rebel250, HONDA Rebel300, HONDA Rebel300
It's a lot easier to ride.
When I was riding my REBEL 1100, I felt like the handlebar was too far away from me, so I was looking for a way to pull the handlebar forward, and I found Earls Gear's Handle setbackRiser. (For REBEL250 and REBEL500) So I bought it and asked HondaDREAM shop to install it.
I was told that if I install the hose as it is, the brake hose would be too tight and it would be dangerous to cut the HandlebarLeft, so I had them change the way the brake hose runs.:Pair (for Left and Right) So I had the angle adjusted slightly and completed the installation.
The Handlebar has been pulled forward to make it easier to ride than the NORMAL state. (>ω<) He's short. (We are 162cm tall.) If you feel that the Handlebar is too far away, you can try it;
View detail
Recommendation for theJapan human body type
I was having a lot of trouble with muscle pain in my shoulders after riding my BMW Motorcycle.
I switched to the f900xr, but the Handlebar is still too far from the seating position or my shoulders hurt.
So I bought the Handlebar Riser which I had been thinking about for a while.
I brought it in and had the shop do the installation since I'm not an expert.
As for the feeling of use, I am writing an impression on the day I ran about 300 km in Touring, but the effect seems to be Large threshold in the feeling that went down from pain to stiff shoulders Level.
The cost is high, but it is effective and I'm glad I put it on because it doesn't bother me at all even if I run like Race ish.
View detail
Perfect for Touring
I have a standard build of 170cm/67kg.
I installed it on my R1200RS.
Although the Normal position was easy to put to sleep, I was suffering from stiff shoulders and back fatigue after long rides.
(This is partly because I usually drive an Up Position Off car or a NAKED)
After I put this Bracket on, I am free from such fatigue. I wish I had bought it earlier.
This is a recommendation for those who use R1200RS as a tourer.
However, Normal position might be better for GunGun attack on the pass.
Easy to install by one person as long as you have the tools.
Required Tools
Torque→Navigation Holder detachment
・13mmRatchet
Torque wrench (You don't need it, but it's better to have it.)
View detail
Fits: BMW R1200GS, BMW R1200GS Adventure, BMW R1250GS, BMW R1200GS, BMW R1200GS, BMW R1250GS Adventure, BMW R1200GS Adventure
An easy positive to buy.
I bought this product because the price is very high and I had a lot of hesitation. Also, the texture of the product is great and I'm glad I bought it. View detail
Secure parking.
When the Side Stand is engaged, the leaning of the vehicle body is reduced and the sense of stability is increased, and parking on uneven terrain has become safe. View detail
Is pleased
I installed Bracket on R1200RS I was able to install it Until now, the Handlebar was too far away to run long distances, which put a lot of strain on my neck and shoulders After installation, my neck and shoulders are lighter and more comfortable, as well as the S-Corner turnaround and figure 8 When I tried driving, etc., the Handlebar operation became light and easy to handle I hesitated a lot for purchase, but I was glad to buy it View detail
I am satisfied..
Product is also high texture and easy to install. The inclination when using Side Stand was also reduced, making it easier to cause bridging. It is slightly expensive, but it is a good item. View detail
More texture and satisfaction than OEM Product
The installation was easy.. If you have another person with Handlebar, you can work with peace of mind, but even one person could do it. If you cover Towel with Towel and protect Handlebar from scratching even if it falls, you can work with even more peace of mind. The ride posture became easier than before, and the long distance touring also became less distressed. View detail