Reviews
In the cold season.
Mounted on GSAdventure
Cold Season
Even the thin leather Gloves are good for keeping my hands cool!
It will be slightly difficult to operate switches.
Once you get used to it, it won't be a problem.
View detail
I can operate Switch directly…
I'm a little concerned about the wind blowing in from both SIDE… View detail
big
It kind of sticks out in front and looks very large when worn.
Of course it's functional, but … I quit.
View detail
Knuckle guard on top
Handlebar cover that can be installed over the knuckle guard
It is easier to be a little aggressive when installing.
DL1000 V-STROM250 and DL1000 V-STROM1050XT installed without problems
But the most important thing is that the handling in driving is the worst.
Button operation is almost impossible.
should be used sparingly
View detail
It's not insanely good, but it's not bad either.
I was able to install the Handlebar of C400GT without any problem.
The operation of the Button is not a problem, but it is necessary to remember the position firmly because Button is hidden naturally.
good point
*It is covered firmly and operation is almost no problem.
It does not interfere with the buttons.
The only thing that is hard to push is the Right Side heaterGrip heaterButton, but it's not used while driving on the Right Side, so it's not a problem.
*Not bad to look at.
Unlike Type, which is like Boxing Gloves, it doesn't show too much of life.
*The price is right.
I was confused with Goldwin, but I decided to go with this one because of the double difference in price.
I thought it was a good price.
What's not so great about it
*The Material is windproof but not very warm, so you don't feel like you're being kept very warm.
*The front of the car is fine, but the wind rolls in or my wrist gets cold.
If you think it's a little cool inside, this may be the cool factor as the wind comes in through the drainage holes. There are two holes inside and one at the entrance. (3rd photo)
I think it is better to block it with Tape etc. in winter because there is no use other than water intrusion in a rainy day.
*Gathers for Waterproof are in the way of getting your hands in and out.
It claims to be large and sturdy for rainy days, but I don't ride in rainy days that bother me that much to begin with, and I don't need holes for drainage.
Why don't you just release that part separately in a rain-compatible MODEL since it's in the way? I thought.
I think I can CostCut it with just Gathers and no holes.
View detail
Fits: SUZUKI Jebel 250XC, SUZUKI RMX250S
Installed on DJEBEL250 XC
Due to the age of the bike, the clutch sides had to be filed down to fit! But this is the only one for DJEBEL!
Large sturdy because if you scrape it a little it will fit!
I'm a random person and I cut way too much!
But Large is sturdy!
YouTube forest road 6th class
https://youtu.be/vC9ZpbxfOk8
View detail
To run in the winter.
I have a Handlebar Guard on my Off car so I thought this was the only way to go. It looks rather large and heavy, the material is solid and hard, and the inside is made of waterproof material to prevent rain from entering. It's easy to put it on. Switch the Blinker etc.Switch operation is not the same as when it is not installed, although it is well thought out. The temperature was 5 degrees Celsius and I put on some gloves and started to test drive. I checked the fit of the Magic tape, but I judged that there was no problem. By the way, I installed NA parts manufacturer's reasonable price one on my Scooter, why I don't feel cold on that one? The only thing I can think of is that it has something to do with the inflow of outside air and the opening diameter when you install it. It is better than wearing nothing, however, because the upper part of the wrist touches the Cover when you stand in the Dirt. When the hand gets cold, it becomes an obstacle in driving operation and the accident is a source. The person of the degree of use of commuting to work and school is a necessity, and the person other than it (including me) consults with Wallet. The above View detail
Material that is prone to defects in workmanship
I really like the size and thermal function, but I am disappointed in the finish and the small details
Speaking of Ruff and Road, you can't fail to see the old equipment manufacturer's It was one of those, and if you trust the sign and buy it, you're in for a rough ride
The worst part is that the seam of the part where the tension is applied is not very good Anyway, the seam is messy and the seam thread pulls on the fabric as you use it and it doesn't take care of the seam It will gradually disintegrate The seams aren't particularly broken, but the cloth is disintegrating so that a draft comes in I was able to use it comfortably for the first 800km or so, and then I had to fight against the draft
Once the gap starts to widen, it seems to be a defect in the product itself, as the gap widens in a chain
The seams on the NeopreneMaterial portion of the product will tear after 800kg of use
It's probably because the seams on the fabric side have widened, putting more strain on the NeopreneMaterial side It is believed that they will come
The next no-no is the cuff
The opening is wide enough so that it doesn't interfere even if you wear gloves, and it looks like there's a rubber in there just in case It is not possible to narrow down the drawing cord, so the airflow from the mouth of the cord is also very strong It's coming in This is a necessary improvement here
The Right Side is pretty solid, but the Left Side is so quick The entire Material disintegrated, so the quality control was poor for a little over a month of use My opinion The design is good, and even if the Handlebar Guard is attached, it's a bad cosmetic There aren't many Covers that can do it, so it's a waste of time
I wish the Manufacturer would do a little better
View detail
Since I purchased it, I can not keep it in place.
PCX (JF56) The mounting. Commuting time, about 30 minutes each way, wearing Winter Gloves at about 10 km.
Just wearing it as it is, although there is hardness of Material out of new, it sags a little with its own weight of Cover.
As a result, Cover contacts Cowl whenever you turn off Handlebar.
Since the entrance and exit of the hand also moves, it is difficult to take out hands a bit. The coldness which the numbness of the fingertips is slightly improved.
?Improvement??
Position the Cover and drill a hole, stop the Bar End Penetrating the Screw and fix it.
As it got fixed, hand out and take it much easier and it did not hang down.
However, I got to grab at right angles to Grip, I do not like how to hold Handlebar and I want to grab Grip diagonally.
?Improvement??
Apply a suitable Color of 1 cm at the end of Bar End and give a little room between Cover and Bar End.
That's why OEMScrew will not deliver, so purchase several long and rust resistant Stainless screws.
Apply Screw lock so that Screw does not loosen.
This almost improved the negative part.
If Knuckle cover or Hand guard is attached, it seems that it is not necessary to do this.
View detail
To counter the coldness of the fingertip
Installed in XT660ZTENEREOEMLever.
It's Square like Chikuwa.
Installation was really Large strange. Even if it got wet with water I was not able to put it easily. Lever It does not even round the tip of the tip.
- I made a kitchen detergent with water that was dissolved
- Even if you try to bare it with bare hands, because it slides for detergent, wear gloves
- The Lever tip fits in guts while spreading the Sponge
- Then rotate it gently and screw it in
- Afterwards rinse it with fresh water generally, dry it and make it. (There should be some detergent, but it will be disintegrated in a while)
= About usability =
Since the area around the finger became fluffy, at first it was Clutch / I could not grasp the feeling of Brake 's operation feeling, drawer' s feeling. You might as well avoid avoiding sudden clutter driving.
In addition, although I ran in the cold wind, I felt the effect was certain. The finger tips will be difficult to cool down. I felt that Aluminum Lever had been taking a lot of body temperature so far. It's Level that you are going to be the last, but it was nice to install.
View detail
I need to get used to operations
Installation is easy and can be done in one Side 1 minute or so.
Since operability is not very good, Large Bold running is strictly prohibited.
Blinker operation is difficult, and Lever operation has a slight sense of discomfort, so some familiarity becomes necessary.
Lever holder does not use Cover because it sticks.
Gloves is as thin as a glove hand is easy to put in and out. Those that stiff or thick are easy to interfere in Cover, so it's hard to put in hands and it is better to stop.
I think that heat retention is pretty good, there are few drafts, Cover's space is Small so it is warm if the temperature is around 10 ° C. It is difficult from 5 ℃ or lower.
Although it is not Waterproof, I did not get flooded especially during 1 hour of rain, so I think that it will not get wet unless it runs all day.
I like being attached without removing the hand guard, Cover is not noticeable, I like the high thermal insulation.
I want the operability to improve especially the part which corresponds to Blinker operation in particular.
View detail
Since the Lever was cold and disagreeable, it equipped with the winter season. Since the direction which does not have summer conversely feels cool, he would like to remove, but primarily, since the wearing itself is hard, removal is not expectable.
Since the Lever was cold and disagreeable, it equipped with the winter season.
Since the direction which does not have
summer conversely feels cool, he would like to remove, but primarily, since the wearing itself is hard, removal is not expectable.
Although it is
Aluminum shaving and has equipped with the thing Lever, appearance and a Lever touch are spoilt in putting this.
A winter season is certainly good also at
.
It is the optimal Items for a person more practical than appearance that makes the
Handle cover this.
View detail
It attached to honda forza MF10. Although it soaks in a package with water and being attached, when doing just like that at first, since it did not enter at all, detergent for kitchen was thinned and used. It entered very well and still ran away.
It attached to honda forza MF10.
Although it soaks in a package with water and being attached, when doing just like that at first, since it did not enter at all, detergent for kitchen was thinned and used.
It entered very well and still ran away.
Since it is developed for motorcycles, die length and thickness are right just.
Since the lever touch also became light, the burden of the fingertip reduced in the urban area which has lever handling frequently.
I think that it is good also for protection against the cold of winter.
Since it is sponge after all, uneasiness is merely in durability.
When also considering the price as sponge, I thought slightly high kana.
Next, I think that it is looked for whether there is any same thing at HOMUSEN when purchasing.
Although it is parts conspicuous [ seldom ], it may be a fashion if it sees from those who see.
View detail