Reviews
neither good nor bad
Model YZF-R25
The three-layer construction is quite thick, and the Magic tape can be extended for universal use.
The size is a little large, but I think it is acceptable.
View detail
Although there is a high degree of freedom
The flexibility is high, but the number of mechanisms is large, so it can be a bit of a challenge to install without thinking about it.
Texture was appropriate for the price, and visibility was not much different from OEM.
With a single cylinder, there is a certain amount of vibration.
The hardness of the moving parts can be adjusted by you, giving you peace of mind.
View detail
Used for DT50Mirror BracketBoots.
I replaced the MirrorBoots on my DT50 because they had deteriorated. To replace the MirrorBoots, remove the screws from the MirrorBoots, remove the MirrorBoots, and install the MirrorBoots. View detail
Good vibes
It is a little difficult to adjust the movement, but I am satisfied. View detail
Fits: HONDA CC110, HONDA CC50, HONDA CT110, HONDA CT125, HONDA CC110, HONDA CC50, HONDA CT110, HONDA CT125
Very cool under the buttocks.
After parking under the blazing sun, it is sometimes uncomfortable to sit on the Seat because it is so hot, but this Mesh cover helps a lot. The MeshMaterial itself does not hold that much heat, so you don't feel it as hot.
Besides, once you start running, you will feel very cool under your buttocks because the wind will be blowing through the 3D MeshMaterial in a nice way. It is too cool when the temperature is low. It might be better not to use it in spring and fall (Lol) Of course, you'll have to leave it off in the winter.
Note that MeshMaterial is more slippery than SeatMaterial, so the holdability of the buttocks will be a little lower. Also, since it is 3-D Mesh, it is thicker and the seat height is about 2 to 3 cm higher, so please be careful about the footing.
Also, Seat shape and the shape of this product. (circular) is not Fit, so some may be bothered by the feeling of doubling up at the aperture on the front side of the Seat when it is covered.
View detail
Load capacity has been increased.
I bought it to carry my backpack, and the extra width of the carrier makes it more stable and gives me more room to sit. View detail
Poor product finish is noticeable, but Style is good
First of all, the overall finish is rough. I thought it was completely bolted on, but it interfered with the Cap Nut of the Normal Rear blinker attachment, so I bent the bracket downwards because it was impossible to attach as it was. It is an Exclusive Carrier for Vehicle, so it would have been nice if they had addressed this issue when they designed it.
The quality of the product is one of the cheaper ones among aluminum carriers, so I guess it can't be helped to some extent, but the second disappointing point is that some of the plating or paint applied to the product has already peeled off to a large extent. The second disappointing point is that a part of the plating or paint applied to the product has already peeled off to a large extent.
I installed the GIVI case, but I had a little trouble installing the Universal base, but it is a square cross section carrier, so that can't be helped. (^^;)
View detail
Just about the most LARGE load capacity with GIVI box installed? Durability is difficult
I bought this Carrier because I liked the way it looked, but within 3 months, both of the brackets on the Carrier broke. I have changed the rating from 3 Stars to 1 Star because it is not a product that I would recommend to other users. View detail
That's the car model Exclusive Design!
It is designed to be installed specifically for the car model, so it can be installed securely with Bolt On exactly.
Since it is lightweight and sturdy as it is named "Aluminum Carrier," it can be driven with confidence even if the Case is installed after each Base is installed.
When the Carrier is installed, the tip of the base is at the top rear of the Seat, so even if the Seat falls over, there is no need to worry about the Seat falling off, and this eliminates the need for maintenance such as battery replacement, rear fluid replacement, and tank removal. This is an excellent product that eliminates the need for maintenance such as battery replacement, rear fluid replacement, and tank removal.
If you must remove the Seat, it is recommended that you remove the Seat after removing the aluminum carrier unless you are prepared to risk the Seat cover being scraped and torn, or at worst, the Seat base being damaged.
In other words, if you have a Carrier, you will never do any maintenance or repair work on it! If you are not one of those people, you will regret buying this Carrier, so I won't recommend it to you.
Since the Carrier is designed for such usage, the user is also recommended to use the Carrier within the scope of the Manufacturer's assumptions.
Clearly Garbage.
View detail
It is highly appreciated that it is easy to operate the Switch and other devices even with the device attached.
I was using an inexpensive Handlebar Cover, but I was dissatisfied with the difficulty of operating switches ….
We decided to replace it with this product.
The operation of switches is smooth without any discomfort, and I liked it at first sight.
The key to this is good wind storm and heat retention, and the performance is so good that summer gloves are not a problem even in December temperatures of 10 to 15°C.
It is going to be essential Items in the winter season.
View detail
Fits: HONDA CRF250 RALLY, HONDA CRF250L
inaccurate
The welding was inaccurate, and some parts were joined at an angle so that they could not be attached properly. In order to attach the bolt even if the bolt was tilted, the bolt hole in the carrier was widened forcibly, and the bolt could be attached.
It looks like they don't do dimensional inspection after welding.
View detail
It looks good
Installed on an Off-road motorcycleRearSeat.
Size Cushioning Breathability with Mesh Good feeling.
View detail
Convenient for long touring
The large size is just right and eases the fatigue of long touring. View detail
Sacrificed serviceability
The side panel is attached together with the side panel, which sacrifices serviceability.
Battery, Fuse cannot be easily accessed.
The side cover on the battery side, which was opened with a single Phillips screwdriver, also requires a hexagonal wrench.
Probably, the cover cannot be opened without loosening the bolts on both SIDE and the Rear Fender.
We installed it halfway through, but decided not to use it.
I wouldn't have bought it if it had more detailed pictures.
View detail
I have no complaints about the performance, but the price is too high.
At the time of purchase, TL125, which was considerably customized for off-road (JD06 TLR125) I put it on a Actually, I used to have a TrailTEC1, but it was damaged in an off-road crash. At that time, TrailTEC1 was discontinued and TrailTEC2 was not yet available, so I used Cat's-eye for Motorcycle speedometer instead. I was using Cat's-eye for Motorcycle speedometer as a substitute.
It is very helpful to be able to check the speed at night when driving on public roads, because it is not practical to check the speed by pressing the button.
However, the CycleComputer for Motorcycle is a Smaller scale. (Less likely to be damaged by falls) The price is cheap, so I think it will be a problem for those who frequently enter Off-road.
In my case, since I am TRIAL, it would be nice if it were a little easier to remove the Bracket, since I do not travel long distances Off and want to remove it in places where I might fall over. I remember that in the first model, I had to remove the handlebar and the grips to install the bracket, so this is also a significant improvement. I was able to fit it by pushing it into the handlebar.
My TL is disced, but there is no gap with Fork and I used Magnet for Motorcycle and it is working fine.
View detail
Satisfied
I installed and used it on ninjaZX14R during overnight long touring (over 1,000k in 2 days) on August 12 and 13, 2023 on a very hot day.
Riding Pants of Denim (part mesh), but even under direct sunlight during a break. My butt is hot." I did not feel like jumping up and down. Even while driving, there was no Breathability is Outclassing." I did not really feel it to the extent that I would say that I was in a good position to do so, My butt steamed and sweaty." I think it was effective because I didn't have any problems. Compared to other companies' products, this product has a thinner finish for a three-piece structure, so there was no discomfort in the riding position and it was comfortable.
View detail
I love using it. Definitely a great product that I can recommend.
I have been using it since my previous Motorcycle, and now I have changed to a new one. The purpose is to prevent rubbing when using Side Back.
I think it used to be thicker Seat.... My memory is a little fuzzy.
It was much easier to use because it was thinner in my hand than I remembered.
The description of the product is Strong adhesion but it's not like it won't come off once it's attached. "Detachable." This is a Type that can be used to
By the way, the reverse side can be recovered to some extent by washing it with a neutral detergent.
Rather, it is this ability to attach and detach The best." and can be detached when needed and when not.
When I didn't need it, for example, I would stick it on the door of my Shoes box or on a smooth surface.
The use is pretty much infinite Large, as shown in the second image.
Seat itself is not very elastic, so three-dimensional curved surfaces should be viewed as almost impossible. It is necessary to devise a way, such as giving up on a clean installation or making a good cut to let it escape.
It contains 3 sheets of 30×25cm, so it is about 3 sheets of A4 size. So, I think you can keep 2 sheets as a spare if you have a certain level of anti-scratch level.
I think it is OK to replace them more and more as they gradually become yellowish due to ultraviolet rays.
OneQuantity for TouringRider:You will not lose anything by purchasing Set! No regrets! Treat before the scratches show the substrate!
View detail
brand items
Throttle assist is installed on most of the motorcycles I own, and it is very useful for large motorcycles to reduce fatigue when touring. It may take some getting used to, but you will soon get used to it. when adjusting the throttle assist, turn the Axel to the closed position. View detail
Large sturdy even if you guessed it?
To install the RALLY50690 on the vehicle, simply remove the OEM Mirror and install the RALLY50690. The RALLY50690 is not a simple installation, but it requires some adjustment. In addition, four nuts were installed using two 17mm Spanners, which are not frequently used (MONKEY Wrench is acceptable), while reading the Instruction Manual on the back of the package, tightening this way and that way. I installed it while reading the instruction manual on the back of the package and thinking, "I tightened it this way, and it loosened this way. By the time I understood the final fine-tuning, the installation was finished, but I am confident that if it gets loose on a touring trip a few months later, I may not be able to put it back together again! (^^;) The shape is very good as it is a curved Pole that does not hit the arm even when standing. I just wish it was easier to tighten. View detail
Purchased because I was going to Camping
I bought it because I had to go camping on short notice.
YamahaLANZA.
It was difficult to fit the screw holes for installation, but I managed to install it. If so, I would like you to think about making the mounting holes more flexible (long holes) or something.
I haven't used it with a load yet, but I was concerned that the surface would fog up if I touched it with a slightly dirty glove or something. (Well, it's okay if you polish it.)
Both SIDE stoppers were installed facing down because the width of the load would be restricted if they were installed according to the instruction manual.
It looks good because Parenthesis is good.
View detail