Reviews
Used for DT50Mirror BracketBoots.
I replaced the MirrorBoots on my DT50 because they had deteriorated. To replace the MirrorBoots, remove the screws from the MirrorBoots, remove the MirrorBoots, and install the MirrorBoots. View detail
Load capacity has been increased.
I bought it to carry my backpack, and the extra width of the carrier makes it more stable and gives me more room to sit. View detail
That's the car model Exclusive Design!
It is designed to be installed specifically for the car model, so it can be installed securely with Bolt On exactly.
Since it is lightweight and sturdy as it is named "Aluminum Carrier," it can be driven with confidence even if the Case is installed after each Base is installed.
When the Carrier is installed, the tip of the base is at the top rear of the Seat, so even if the Seat falls over, there is no need to worry about the Seat falling off, and this eliminates the need for maintenance such as battery replacement, rear fluid replacement, and tank removal. This is an excellent product that eliminates the need for maintenance such as battery replacement, rear fluid replacement, and tank removal.
If you must remove the Seat, it is recommended that you remove the Seat after removing the aluminum carrier unless you are prepared to risk the Seat cover being scraped and torn, or at worst, the Seat base being damaged.
In other words, if you have a Carrier, you will never do any maintenance or repair work on it! If you are not one of those people, you will regret buying this Carrier, so I won't recommend it to you.
Since the Carrier is designed for such usage, the user is also recommended to use the Carrier within the scope of the Manufacturer's assumptions.
Clearly Garbage.
View detail
It is highly appreciated that it is easy to operate the Switch and other devices even with the device attached.
I was using an inexpensive Handlebar Cover, but I was dissatisfied with the difficulty of operating switches ….
We decided to replace it with this product.
The operation of switches is smooth without any discomfort, and I liked it at first sight.
The key to this is good wind storm and heat retention, and the performance is so good that summer gloves are not a problem even in December temperatures of 10 to 15°C.
It is going to be essential Items in the winter season.
View detail
Convenient for long touring
The large size is just right and eases the fatigue of long touring. View detail
I love using it. Definitely a great product that I can recommend.
I have been using it since my previous Motorcycle, and now I have changed to a new one. The purpose is to prevent rubbing when using Side Back.
I think it used to be thicker Seat.... My memory is a little fuzzy.
It was much easier to use because it was thinner in my hand than I remembered.
The description of the product is Strong adhesion but it's not like it won't come off once it's attached. "Detachable." This is a Type that can be used to
By the way, the reverse side can be recovered to some extent by washing it with a neutral detergent.
Rather, it is this ability to attach and detach The best." and can be detached when needed and when not.
When I didn't need it, for example, I would stick it on the door of my Shoes box or on a smooth surface.
The use is pretty much infinite Large, as shown in the second image.
Seat itself is not very elastic, so three-dimensional curved surfaces should be viewed as almost impossible. It is necessary to devise a way, such as giving up on a clean installation or making a good cut to let it escape.
It contains 3 sheets of 30×25cm, so it is about 3 sheets of A4 size. So, I think you can keep 2 sheets as a spare if you have a certain level of anti-scratch level.
I think it is OK to replace them more and more as they gradually become yellowish due to ultraviolet rays.
OneQuantity for TouringRider:You will not lose anything by purchasing Set! No regrets! Treat before the scratches show the substrate!
View detail
brand items
Throttle assist is installed on most of the motorcycles I own, and it is very useful for large motorcycles to reduce fatigue when touring. It may take some getting used to, but you will soon get used to it. when adjusting the throttle assist, turn the Axel to the closed position. View detail
Great for touring. Try a few different positions on the bar in a parking lot before you take it out
I've used a few variations of throttle assist grips over the years and so far this has been my personal favorite. The full palm grip doesn't make a huge difference but it gives you a bit more feel than some of the smaller surface area grips out there.They all work but for a few extra bucks I personally prefer having more surface area under my hand to work with to control my throttle.This little price of plastic has made long trips a helluva lot less taxing on my wrist and the occasional numbness is pretty much gone. You just let your hand rest on it and it keeps the throttle where you need it. DO take your time getting the angle on this thing EXACTLY where you want it and ride it around a parking lot a few times before you get out into traffic. I almost pitched my bike up into a wheelie the first time I tried it out. You want it angled just slightly up from where your hand rests on the handlebars. View detail
To combat the cold.
Used for cold weather.
It prevents your hands from getting cold from Lever.
View detail
Fee Ring good!
*Motivation to purchase
The rattles on the top and bottom of the lever became too large, and it started to interfere with the gripping motion.
When the lever is fully gripped, the lever hits the finger holding the grip, making it impossible to operate the clutch delicately.
0Because the brake lever was broken due to a fall.
Installation
Simply use 0OEMBolt to replace the levers.
0 Nothing special was done. We just applied Grease at the time of installation.
Current state
0After replacement, there's a lot less rattling than with the OEM!
0The fee rings when gripping have also improved very much.
The Brake lever is equipped with an Adjust Screw, which allows for subtle adjustment of the lever position at the rider's convenience.
Effects
I like the look and feel of the Race ish because it's shorter than the 0OEM Lever!
Brake lever and clutch lever are non-slip. (0-type Dent processing) The fee ring is very good because there is very little slipping sensation when you grip it, and you can feel the force of your grip being directly transmitted to the lever!
The 0Clutch, in particular, can be gripped all the way to the end without the lever end hitting the finger gripping the grip, so I feel that accurate clutch operation is now possible, especially when using 1 pc finger operation.
0To use an actual driving example, the front up clutch operation when going over logs has become very direct and timing has become easier to grasp.
The position of the brake lever can be adjusted so that it can be changed individually for multiple riders, allowing for a more subtle rider feel.
View detail
Very effective and good
It's the best Cover I've ever used, easy to get in and out of the hand, although it would be great if the fingertips were improved. View detail
It keeps out the cold.
It will keep your hands much colder in the winter.
I highly recommend it.
View detail
Off-road standard
Quantity to CT110 HUNTER CUBCT125:Pair (for Left and Right) Installed at the same time.
I am used to it because I have it on my SEROW and it is very convenient and easy to fold up.
It takes some time to adjust the firmness when installing it if you are not used to it, but once you understand the structure, you can freely adjust the angle.
Mirror can be folded for convenient and unobstructed parking in narrow bicycle parking lots.
View detail
If you don't care about its appearance, it is usable enough.
First of all, when installing the cover, the hole was too small for SR400, and the cover could not be inserted unless the hole was widened with scissors.
Once the Cover was in place, all that was left was to fix it to Mirror using Magic tape, so installation was easier than expected.
The feeling is that when you put your hand in the Cover, it is no problem with thin gloves, but with thick gloves it is difficult to put your hand in, so it takes some ingenuity and getting used to.
It is slightly snug, but it still blocks most of the wind, so thicker Gloves will not make you feel cold.
In my opinion, it works quite a bit better than it looks. I am glad I bought it. Now I wonder how durable it will be.
View detail
Not like the cheap stuff.
Vehicle:Ninja 250 (JBK-EX250L)
Grip:Endurance Grip heaterHG115 (Grip diameter 34Φ)
Inexpensive ones are available for about 500-700 yen, but they are not as strong as this product and will crack and become unusable after several uses (or at worst the first use).
However, this product has high strength and high quality, so it can be used for a long time without replacement, resulting in better cost performance.
(although 1,320 yen is hard to come by when there are less expensive ones out there...)
As for the effects, high speed cruising became easier and fatigue was reduced.
It was also made in Canada. （It was made in Canada, which is very rare.)
View detail
Hand warmer
It is easy to put on and operate around the Switch without being affected by wind, and it is also easy to remove, making it the perfect Items for the winter season. View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
High quality lightweight luggage rack
Very well built rack. Less strong than stainless steel but it is very lightweight as it's aluminium. High quality finish. Clean welds. Highly recommended product from Rough & Road. Just don't exceed the carrier's weight limit. Recommend for soft bags. Top box installation is possible too. View detail
[buying motive] The product ] which was seen as the candidate besides [point which got interested] [, [after-use comment], [comprehensive evaluation]
[buying motive] The product ] which was seen as the candidate besides [point which got interested] [, [after-use comment], [comprehensive evaluation] View detail
Fits: YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X
In comfort, it attached so that a path-through-a-wood run could be carried out. 4MM thickness differs in sense of security. It was not distorted and stopped also worrying the stone which hits a crankcase in a rash thing.
In comfort, it attached so that a path-through-a-wood run could be carried out.
4MM thickness differs in sense of security.
It was not distorted and stopped also worrying the stone which hits a crankcase in a rash thing.
View detail
light
It is light and good because it is the smallest necessary large size and function.
When used Off, the vibration is Large, so the Mirror must be firmly secured in place to prevent it from moving.
The universal joint got stuck.
Merit with moving parts is lost.
It will depend on how it is used, but it will require some ingenuity.
The quality is pricey, but there is nothing particularly wrong with it.
View detail