Reviews
Poor product finish is noticeable, but Style is good
First of all, the overall finish is rough. I thought it was completely bolted on, but it interfered with the Cap Nut of the Normal Rear blinker attachment, so I bent the bracket downwards because it was impossible to attach as it was. It is an Exclusive Carrier for Vehicle, so it would have been nice if they had addressed this issue when they designed it.
The quality of the product is one of the cheaper ones among aluminum carriers, so I guess it can't be helped to some extent, but the second disappointing point is that some of the plating or paint applied to the product has already peeled off to a large extent. The second disappointing point is that a part of the plating or paint applied to the product has already peeled off to a large extent.
I installed the GIVI case, but I had a little trouble installing the Universal base, but it is a square cross section carrier, so that can't be helped. (^^;)
View detail
Large sturdy even if you guessed it?
To install the RALLY50690 on the vehicle, simply remove the OEM Mirror and install the RALLY50690. The RALLY50690 is not a simple installation, but it requires some adjustment. In addition, four nuts were installed using two 17mm Spanners, which are not frequently used (MONKEY Wrench is acceptable), while reading the Instruction Manual on the back of the package, tightening this way and that way. I installed it while reading the instruction manual on the back of the package and thinking, "I tightened it this way, and it loosened this way. By the time I understood the final fine-tuning, the installation was finished, but I am confident that if it gets loose on a touring trip a few months later, I may not be able to put it back together again! (^^;) The shape is very good as it is a curved Pole that does not hit the arm even when standing. I just wish it was easier to tighten. View detail
Purchased because I was going to Camping
I bought it because I had to go camping on short notice.
YamahaLANZA.
It was difficult to fit the screw holes for installation, but I managed to install it. If so, I would like you to think about making the mounting holes more flexible (long holes) or something.
I haven't used it with a load yet, but I was concerned that the surface would fog up if I touched it with a slightly dirty glove or something. (Well, it's okay if you polish it.)
Both SIDE stoppers were installed facing down because the width of the load would be restricted if they were installed according to the instruction manual.
It looks good because Parenthesis is good.
View detail
In the cold season.
Mounted on GSAdventure
Cold Season
Even the thin leather Gloves are good for keeping my hands cool!
It will be slightly difficult to operate switches.
Once you get used to it, it won't be a problem.
View detail
I can operate Switch directly…
I'm a little concerned about the wind blowing in from both SIDE… View detail
Folding Mirror classic
I bought it again because I fell down in Asphalt and broke it off at the base of the ball.
It is reasonably priced, easy to adjust, and safe to use.
View detail
big
It kind of sticks out in front and looks very large when worn.
Of course it's functional, but … I quit.
View detail
wobbly
It is wobbly when driving. I'm wondering if it's sturdy enough to run at high speed Large, I'll strengthen it using the method I saw on YouTube. View detail
Knuckle guard on top
Handlebar cover that can be installed over the knuckle guard
It is easier to be a little aggressive when installing.
DL1000 V-STROM250 and DL1000 V-STROM1050XT installed without problems
But the most important thing is that the handling in driving is the worst.
Button operation is almost impossible.
should be used sparingly
View detail
It's not insanely good, but it's not bad either.
I was able to install the Handlebar of C400GT without any problem.
The operation of the Button is not a problem, but it is necessary to remember the position firmly because Button is hidden naturally.
good point
*It is covered firmly and operation is almost no problem.
It does not interfere with the buttons.
The only thing that is hard to push is the Right Side heaterGrip heaterButton, but it's not used while driving on the Right Side, so it's not a problem.
*Not bad to look at.
Unlike Type, which is like Boxing Gloves, it doesn't show too much of life.
*The price is right.
I was confused with Goldwin, but I decided to go with this one because of the double difference in price.
I thought it was a good price.
What's not so great about it
*The Material is windproof but not very warm, so you don't feel like you're being kept very warm.
*The front of the car is fine, but the wind rolls in or my wrist gets cold.
If you think it's a little cool inside, this may be the cool factor as the wind comes in through the drainage holes. There are two holes inside and one at the entrance. (3rd photo)
I think it is better to block it with Tape etc. in winter because there is no use other than water intrusion in a rainy day.
*Gathers for Waterproof are in the way of getting your hands in and out.
It claims to be large and sturdy for rainy days, but I don't ride in rainy days that bother me that much to begin with, and I don't need holes for drainage.
Why don't you just release that part separately in a rain-compatible MODEL since it's in the way? I thought.
I think I can CostCut it with just Gathers and no holes.
View detail
Fits: SUZUKI Jebel 250XC, SUZUKI RMX250S
Installed on DJEBEL250 XC
Due to the age of the bike, the clutch sides had to be filed down to fit! But this is the only one for DJEBEL!
Large sturdy because if you scrape it a little it will fit!
I'm a random person and I cut way too much!
But Large is sturdy!
YouTube forest road 6th class
https://youtu.be/vC9ZpbxfOk8
View detail
To run in the winter.
I have a Handlebar Guard on my Off car so I thought this was the only way to go. It looks rather large and heavy, the material is solid and hard, and the inside is made of waterproof material to prevent rain from entering. It's easy to put it on. Switch the Blinker etc.Switch operation is not the same as when it is not installed, although it is well thought out. The temperature was 5 degrees Celsius and I put on some gloves and started to test drive. I checked the fit of the Magic tape, but I judged that there was no problem. By the way, I installed NA parts manufacturer's reasonable price one on my Scooter, why I don't feel cold on that one? The only thing I can think of is that it has something to do with the inflow of outside air and the opening diameter when you install it. It is better than wearing nothing, however, because the upper part of the wrist touches the Cover when you stand in the Dirt. When the hand gets cold, it becomes an obstacle in driving operation and the accident is a source. The person of the degree of use of commuting to work and school is a necessity, and the person other than it (including me) consults with Wallet. The above View detail
Off-road mirror
Exchange to Mirror, which folds down for forest road touring.
Plastic's texture is poor.
The price is a little higher than similar products.
The shape is general for Off-Road Folding Mirror.
The feel is Level with no problems.
View detail
As a consumable
Material is worse than I expected.
The whole construction looks cheap.
The Napole OnRadical mirror I used before was more solid.
It folds up and is convenient for use on forest roads.
View detail
It is effective in preventing damage.
There are various types of Tank Pads, but if you stick a Tank Pad on it, it will destroy the design of the Tank, and if you prefer not to stick anything on it, I recommend you to stick it on.
Transparent [Color] The clear film is inconspicuous and scratch resistant.
View detail
Good for protecting, but too thick?
I bought it to prevent chafing.
Cut and paste it with scissors, but because it is quite thick film, it peels off when you paste it on a curved surface.
In terms of thickness, it seems to be quite strong against rubbing, etc.
I think it is suitable for use in the chafing of the strings when the SeatBack is installed.
In terms of quantity, the size is enough to cover the required portion of 1 Set for 1 Vehicle.
I'm giving it this rating because it's not very convenient to use because it just comes off.
I think it could be a little thinner.
View detail
Material that is prone to defects in workmanship
I really like the size and thermal function, but I am disappointed in the finish and the small details
Speaking of Ruff and Road, you can't fail to see the old equipment manufacturer's It was one of those, and if you trust the sign and buy it, you're in for a rough ride
The worst part is that the seam of the part where the tension is applied is not very good Anyway, the seam is messy and the seam thread pulls on the fabric as you use it and it doesn't take care of the seam It will gradually disintegrate The seams aren't particularly broken, but the cloth is disintegrating so that a draft comes in I was able to use it comfortably for the first 800km or so, and then I had to fight against the draft
Once the gap starts to widen, it seems to be a defect in the product itself, as the gap widens in a chain
The seams on the NeopreneMaterial portion of the product will tear after 800kg of use
It's probably because the seams on the fabric side have widened, putting more strain on the NeopreneMaterial side It is believed that they will come
The next no-no is the cuff
The opening is wide enough so that it doesn't interfere even if you wear gloves, and it looks like there's a rubber in there just in case It is not possible to narrow down the drawing cord, so the airflow from the mouth of the cord is also very strong It's coming in This is a necessary improvement here
The Right Side is pretty solid, but the Left Side is so quick The entire Material disintegrated, so the quality control was poor for a little over a month of use My opinion The design is good, and even if the Handlebar Guard is attached, it's a bad cosmetic There aren't many Covers that can do it, so it's a waste of time
I wish the Manufacturer would do a little better
View detail
The image..
I bought it based on the image alone
I was very disappointed to receive the product, Elastic band alone does not help It was a learning experience
I'd like to see a clearer picture
View detail
It's broken twice
The second breakage was my own careless mistake in forgetting to ask for some Parts, though
Still, it's hard to be damaged twice
The cause would be structure
The seat is cracked at the welded area where the screws are tightened together I did
I didn't know about the fixation there, but I asked for parts of other broken parts to be reattached Break between the Parts frame screwing point and the Carrier screwing point While driving without luggage
I don't want to buy a new one from scratch, so I'm thinking of adding a bracket to support it from below It is
View detail
Since I purchased it, I can not keep it in place.
PCX (JF56) The mounting. Commuting time, about 30 minutes each way, wearing Winter Gloves at about 10 km.
Just wearing it as it is, although there is hardness of Material out of new, it sags a little with its own weight of Cover.
As a result, Cover contacts Cowl whenever you turn off Handlebar.
Since the entrance and exit of the hand also moves, it is difficult to take out hands a bit. The coldness which the numbness of the fingertips is slightly improved.
?Improvement??
Position the Cover and drill a hole, stop the Bar End Penetrating the Screw and fix it.
As it got fixed, hand out and take it much easier and it did not hang down.
However, I got to grab at right angles to Grip, I do not like how to hold Handlebar and I want to grab Grip diagonally.
?Improvement??
Apply a suitable Color of 1 cm at the end of Bar End and give a little room between Cover and Bar End.
That's why OEMScrew will not deliver, so purchase several long and rust resistant Stainless screws.
Apply Screw lock so that Screw does not loosen.
This almost improved the negative part.
If Knuckle cover or Hand guard is attached, it seems that it is not necessary to do this.
View detail