Reviews
Fits: SUZUKI address V125, SUZUKI Address V125S
RK TAKASAGO CHAIN GATES Reinforced ScooterBelt
I bought it because the price was reasonable. I don't know how long it will last since I haven't replaced it yet, but if I use it and the rubbers are good, I will buy it again. View detail
Fits: YAMAHA TMAX500, YAMAHA TMAX500, YAMAHA TMAX500, YAMAHA TMAX500, YAMAHA TMAX500
RK RK TAKASAGO CHAIN GATES [Gates
Replace with the same product currently in use.
It is the same product and has not yet been replaced.
Since it is as comfortable to use as the OEM Product to date, we purchased the same one.
View detail
Less expensive than OEM Product and satisfied
Unlike Yamaha's Pulley, Honda's Pulley with GEAR was difficult to remove.
I don't have an Impact wrench, so I fixed it with an ASTROPulleyHolder, but
I used a 22mm 1/2-inchesSocket wrench and tried to turn it with all my might.
Once I got out of GEAR in the middle of the game and hit the CellMotorPinion holder with momentum.
The Holder was partially broken. I've changed Holder to Quantity:Set it again.
I managed to get it off, but I had to remove the Clutch to get the Belt off.
I wanted to get the Impact wrench.
The tightening torque is 108N-m on the Pulley side, and 108N-m on the Clutch Side. : It is said to be 49N・m.
OEMBelt is also quite cracked and is replaced immediately.
I compared the widths and there wasn't much difference.
After accelerating to a certain speed and then stopping, the gurgling sound before the replacement
It is much quieter after replacement.
Same OEM Product (16g) I replaced the WeightRoller with a new one, and I thought the behavior would be the same, but
I think it's faster to reach the maximum speed because of the increased width inside the Belt.
I'm going to open the Case after about 1000km.
View detail
Fits: HONDA clair-scoopy, HONDA clair-scoopy, HONDA SmartDio, HONDA SmartDio, HONDA byte
Great for competition
It is much thinner and lighter than the OEM Belts
It's great for use in scooter races because the weight reduction in the rotating parts helps to improve acceleration I think
As for city riding, the Belt is thinner and can take the same load in the same small area The wear on the Pulley side (rather than the OEM's) is much greater than the durability of the Belt itself I am slightly concerned that this will be promoted
I haven't had any noticeable symptoms after about 2000km of use, so it may be hard to get rid of it
View detail
The price is the best
It is the cheapest of the Kevlar type of Aramid fiber
Performance is fine
I think the price is relatively high for this Site
It's a product that comes in a package and is safe to use
View detail
A little thin
【What made you decide the purchase?】
Because it is a product of RK with a reputation as ChainManufacturer and the price was cheap.
【How was it actually used?】
The texture is also close to the OEM, it can be used without problems, but I am worried about durability because it is a little thin.
【Was it difficult to install? (Hard parts case)】
Easy, you need special tool to remove Pulley and Driven.
【Please tell me the point of installation and hang (in the case of Hard parts)】
Set to Drive shaft before Pulley and Boss, hang Belt on Driven, open it, drop it a little and set it to Driven Shaft, then Belt will hang more easily on Drive shaft side.
[Is there anything I was disappointed about?]
A little narrow width.
【Hope for Manufacturer - Please let me know if you have any improvement points]
I want you to describe dimensions as well as compatible models.
【Have you compared items?】
OEM Product (4KN-17641-00)
OEM Product has a width of 16. 5 mm Meter and a bit thicker than this.
[Others]
In case of Minarei Engine, OEMBelt is 3AA - 17641 - 00 ProductNo (16. 5 × 750), but even this Normal pulley is so short that Driven may have bottom, so this 4KN-17641-00 ProductNo equivalent (16. Belt of 5 X 760) is recommended.
By the way, even among 4 KNGEAR, the Second Type Model since 2003 (Commonly known as GEAR C) Belt of 4KN-17641-10 and ProductNo in the last two digits are different, it seems to be a short Belt of almost the same size as 3AAProductNo, so it is a caution.
For HardTuner who are seeking longer Belt, Peugeot - Belt of Speed ??fight (17. I will tell you about 5 X 765.
View detail
Used for Made in Taiwan Scooter.
I used it for GTX 125 made by Taiwanese Manufacturer CPI.
Even NORMAL, it was V Belt made by three stars, but it was torn by 12000 km. So this time, I tried to strengthen RK GATES ScooterBelt.
There was a slight difference in size, but after assembly it is running smoothly. I am in good shape.
Regarding durability, I do not know yet, but I think I will purchase this Belt next time.
View detail
Anyway it's cheap!
Scooter Belt is sold from various Manufacturers, but this time I was attracted by the cheapness and made it to SKoterBelt of RK.
Until I purchased it, I did not know that RK sells For Scooter Belt.
However, the most problematic part of this part is durability.
It's durable in Impre of others - - - I saw the opinion that.
So it's just installed now and there is nothing wrong with it, but it is noteworthy in the future.
I'd like to check if I run about 500 KM for the time being.
View detail
To Refresh the drive system
We introduced reinforced Belt to perform Custom at the same time as Maintenance of Drive system. Although OEM is better in terms of durability, we chose cheap reinforcement Belt, considering the Custom content. View detail