Reviews
Bright and practical
Compared to NORMAL, it is very bright and easy to see.
We purchased the dark red color, and although the darker color of the lenses might make it difficult to see from behind, this was not the case and the visibility is sufficient.
I am very happy with the color and the tightening effect on the body of the car.
And the Instruction Manual that came with it was quite clear and helpful, which I liked.
It is easy to install and Couplet-on.
This is a product from Recommendation
View detail
KITACO:High flasher measures for Unbreakable lens
I am posting a Review after about 2 years of implementation.
I introduced this as a countermeasure against high flasher when I change the blinker of KLX125 to unbreakable lens.
It is easy to install and works perfectly.
Note that the harness is a bit longer than the OEM Relay, so the waterproof cover on the body side will not fit properly.
However, if each waterproof cover is wrapped with Self Fuser Tape, it is large and durable.
It has been driven about 5,000 km in 2 years, has been caught in large rainstorms while touring, has been igotting in a vomit muddy Enduro race on a rainy day, etc., etc. Water resistance test of a reasonable strength. (?) I have been through the following and to this day have had no problems.
High flasher is illegal and must be addressed.
This product is an easy one-shot solution, and we recommend it!
View detail
It looks different!
Ready-made products are Material:Since it is a plastic item, I purchased an air valve cap in the same color as the Collar Aluminum foil.
The color is also the same color, so it looks great.
View detail
Universal and easy to use
Material:Stainless Steel 8mmCap bolts are available at Home center in various lengths (about 150 yen per pc).
Even if it is not a car-specific product, this one from Universal was sufficient for me.
Also, there is no extra Logo, etc., which is nice and clean.
View detail
The classic European Blinker
This is a replacement for an OEM Blinker. I am satisfied with the stylish look. View detail
Fits: KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI NINJA250R, KAWASAKI NINJA400R, KAWASAKI NINJA650, KAWASAKI NINJA650R, KAWASAKI Z750, KAWASAKI Z750S, KAWASAKI Z800, KAWASAKI ZEPHYR1100, KAWASAKI ZRX1100, KAWASAKI ZRX1200DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZX-7R, KAWASAKI ZX-9R, KAWASAKI ZX14R, KAWASAKI ZZR1100, KAWASAKI ZZR1200, KAWASAKI ZZR1400
Quite normal! That's the good part!
It was purchased to be installed on an ELIMINATOR 400.
IronWeight inside and Material outside:I like that the AluminumCover is a separate body. (,,> <,,)
I bought Silver because I was planning to AnodizedOrder only the Aluminum Cover.
I requested Anodized from Koken and installed the Pink-colored one.
(Wife's request)
The weight is a little heavy, but the protrusion is moderate, so it looks good.
View detail
Bolt is becoming White muddy.
It looks better now. I have another Large Motorcycle, and I am thinking about installing it. View detail
Fits: KAWASAKI ZRX1200S, KAWASAKI ZRX1100, HONDA CB400SF, HONDA CB1300 SF, YAMAHA XJR1200, YAMAHA XJR1300, YAMAHA XJR400, KAWASAKI ZRX1200R, KAWASAKI ZrX1200ZrX1200 DAEG, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF
I think it's good for a little dress-up!
I am satisfied with the quality of the product.
I think it is good for dress-up around handlebar.
View detail
tw200
[How is it used?
Touring
Was the one you received as per Image?
YES
Was the installation difficult?
Easy
How was your experience with it?
Very good
[Included Parts:were they on?
It was attached.
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
I wanted Black!
This is great! It's a bit of an accent. View detail
Fits: YAMAHA SR500, YAMAHA SR400, その他 , その他 , その他 , SUZUKI DRZ400, SUZUKI DRZ400
If you put on the outside of the company with a good exit, you can use Setting.
I used it for an OEMcarburetor overhaul. 。
Carburetor has parts called "Jet" such as Main Jet, Needle, Pilot Jet (Slow Jet), etc., right?
What is the Pilot Jet used in this project?
What is Pilot Jet?
Pilot Jet Slow Jet. Or, IdolJet. also called 。
Jet to lighten the fuel in the Pilot system. 。 Weighs the amount of fuel in low-speed operation from Idling 。 The larger the number, the larger the diameter and the thicker the mixture.
*Fuel is supplied from the Pilot system→Idling at low speeds.
And, Pilot Jet Or Slow Jet is exactly the same role, but it is called by a different name.
Why are they called by different names?
★ Pilot Jet
→ Name used for Mikuni Carburetor 。
★ [Slow Jet]
→Name used for KEIHINCarburetor.
The parts have the same function but are manufactured by different manufacturers.
And why Pilot Jet (Slow Jet)
need to be adjusted?
And Pilot Jet (Slow Jet) has a thing called a number.
■Thinning the number one small cherry→ thinning.
■Large kiku→ thicken the number.
This is an adjustment that
By the way, when do you actually perform setting?
Setting example
~Pilot Jet (Slow Jet)
When you want to make it thicker (to increase the number)
→Idling - unstable rotation at low speeds.
→Engine is hard to take.
→ After Fire from Exhaust System during embr.
I was in After Fire and poor starting when embracing.
Thinning (lowering the number)
→Idling sound dull.
→Black smoke coming from Exhaust System.
I think the most common case is to replace the exhaust system with an external exhaust system with good ventilation.
I also have an external Exhaust System, so I'm moving up to the OEM Pilot Jet #25→#27.5.
How to exchange ~OEMMikuniCVcarburetor
(1) Turn off Fuel Cock.
↓
(2) Remove Gasoline in the carburetor.
Loosen the drain bolt and it will come out.
↓
(3) Use Phillips Screwdriver to remove the lower no-screw of the carburetor. The screw is soft, so do not lick it. Turn counterclockwise.
↓
Open the inside, and you will see a large sized Bolt (main jet).
Pilot Jet is located under the
↓
?Use a slotted screwdriver to remove the existing Pilot Jet.
↓
(6) Turn the new Pilot Jet in the place where you removed it by hand gently first, and finally tighten it with a slotted screwdriver. Do not overtighten.
↓
Large sturdy if it is restored with ? ?→?.
After that, start the engine and adjust the speed of idling by Pilot screw, etc.
The number of Pilot Jet that is originally attached to SR400 is #25.
〜After replacement
○ After Fire at the time of embellishment has disappeared.
○The connection of acceleration from low speed to medium speed has become smoother.
If the carburetor vehicles are changed to an external exhaust system, I think it is better to adjust not only the OEM carburetor but also the external carburetor.
View detail
Fits: KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI NINJA250R, KAWASAKI NINJA400R, KAWASAKI NINJA650, KAWASAKI NINJA650R, KAWASAKI Z750, KAWASAKI Z750S, KAWASAKI Z800, KAWASAKI ZEPHYR1100, KAWASAKI ZRX1100, KAWASAKI ZRX1200DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZX-7R, KAWASAKI ZX-9R, KAWASAKI ZX14R, KAWASAKI ZZR1100, KAWASAKI ZZR1200, KAWASAKI ZZR1400
Vibration improvement at high speed
I purchased the Black color and it blends in well with the Grip. Installation was easy. I have not applied Screw lock yet, but I will do so after purchasing it at a later date. I was worried about the other company's HeBeaverWeight, but I am glad I chose this one. I have been driving at high speeds for about 30 minutes and my palms are no longer numb from the vibration at 6000 RPM. I wish I had bought it earlier. View detail
ETC Antenna BracketTYPE 3
Can be installed by co-tightening with Mirror Bracket.
Installation should be completed in 15 minutes.
The product is not very thick, so you can slightly adjust the direction of the ETCAntennas etc. by hand.
View detail
Material:Material on the Caliper side of Aluminum:Banjo bolt in Aluminum.
Since the caliper side is aluminum, we replaced the OEM steel banjo bolt with an aluminum banjo bolt to prevent thread galling due to electrical corrosion when replacing the brake hose.
Since it is GOODRIDGE compatible, OEM's NORMAL could be used, but replaced with this product for the above reasons.
Since it is a product of a proper manufacturer, there are no problems with thread accuracy, quality of anodized processing, etc., and it can be used with confidence.
View detail
![[For Specific Models] Blinker Set Bullet Type](https://img.webike-cdn.net/catalogue/images/51075/023099-33shironuki_TS.jpg)
Fits: YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW225E
Blinker replacement changes appearance
I am satisfied with the material, good texture and smooth installation. View detail
tw200
[How is it used?
Touring
Was the one you received as per Image?
Yes
Was the installation difficult?
Easy with special tools
How was your experience with it?
Large strange
[Included Parts:were they on?
RClip
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI NINJA250R, KAWASAKI NINJA400R, KAWASAKI NINJA650, KAWASAKI NINJA650R, KAWASAKI Z750, KAWASAKI Z750S, KAWASAKI Z800, KAWASAKI ZEPHYR1100, KAWASAKI ZRX1100, KAWASAKI ZRX1200DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZX-7R, KAWASAKI ZX-9R, KAWASAKI ZX14R, KAWASAKI ZZR1100, KAWASAKI ZZR1200, KAWASAKI ZZR1400
There is an effect that can be seen in the "Hadrill
Vibrations at highway speeds are noticeably reduced, at 80km I don't feel it at all, at 90km it's just a little bit bothersome. Motorcycle is the New Model Eliminator. View detail
It gives a nice Retro feel.
It was inexpensive, easy to install, and gave a nice Retro feel.
I wonder if old Motorcycles had them.
There was just a little left over after one round of Fuel Tank.
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, HONDA CB400SB
I'm glad I bought it!
I wasn't sure whether to buy it, but, I'm glad I did! ♪ (??????) ♪ View detail
rebel 1100 dct
It's perfect for the Rebel 1100 handlebar. It was installed well and tuning was smooth. The delivery and process were perfect. However, it's not for the Honda Rebel 1100 only.
It's a pity that the part needs to be processed.
It's perfect for the Rebel 1100 handlebar. It was installed well and tuning was smooth. The delivery and process were perfect. However, it's not for the Honda Rebel 1100 only.
It's a pity that the part needs to be processed ------------------------------------------ ---------------- It's perfect for the Rebel 1100 handlebar. It was installed well and tuning was smooth. The delivery and process were perfect. However, it's not for the Honda Rebel 1100 only. It's a pity that the part needs to be processed. It's perfect for the Rebel 1100 handlebar. It was installed well and tuning was smooth. The delivery and process were perfect. However, it's not for the Honda Rebel 1100 only. It's a pity that the part needs to be processed. Powered by Google Translator
View detail