Reviews
Mirror Hole Cap
I bought this to hide the Mirror hall as I changed my CB223S to a Bar end mirror.
Note that the quantity is 1 pc.
If you value cosmetics, you can use Homsen Screws or Vinite.
The texture is good
View detail
Fits: SUZUKI GSX-R1000, SUZUKI GSX-R1000R, SUZUKI GSX1300R
Isn't the price too high?
The anodized treatment is also very colorful, and the handlebar area is now more colorful, giving it a more luxurious feel. However, I wonder if the price is too high. View detail
At a glance, it looks unreliable, but I use it without problems!
[How is it used?
Since the suspension of CB50s was diverted, the washer of the banjo bolt was replaced together with it during the maintenance of the brake.
How was your experience with it?
The Aluminum Washer does get saggy over time, but the replacement provides peace of mind. Fluid does not leak, and it can be used without any problems.
How did it compare to other products?
At a glance, the quality may seem poor, but I feel safer using it because it is made by POSH rather than a cheap, inferior product.
[Points to note]
Use the product in accordance with the specified Torque. Do not use force.
Since it is a consumable item, it would be easier to replace it at a lower price, but it is a manufacturer's product, so I guess it can't be helped.
View detail
Cowl stop.
The 900SS has a spacer and bolt that fly out of place due to vibration, and the front cowl that holds the spacer in place needs to be mass-tightened regularly as the bolt will loosen if you are not careful. Posh rubber is similar to the OEM product and I think the quality is even better. View detail
It is surprisingly noticeable when you put it on, which is good.
Used 4 pieces for Handlebar Clamp on XSR900.
The price is a little high, though, as it is a place that is always in view while driving, so it is highly satisfactory.
We were lucky to have a Gold similar to Fork.
M8 is with O-ring.
I found out when I put it on that I can see the silver color of the Bolt. I am satisfied with it because I can't see it while driving.
View detail
Looking for ways to use it.
I was going to use it for a Handlebar Clamp on my XSR900, but it was not available in this size, so I ended up buying it in vain.
I ended up buying M6, M8, and M10, all of which are of good quality and may not be as expensive as they should be.
I've seen some of these products not match the color when you buy them, but the gold of this series is similar to the gold of the XSR900's Fork.
M8 and M10 are O-rings. We will keep them until we can find a use for them.
View detail
It looks surprisingly different and good.
XSRLogoQuantity under XSR900 Meter:Pair (for Left and Right) Used for
The price is a little high, though, as it is a place that is always in view while driving, so it is highly satisfactory.
We were lucky to have a Gold similar to Fork.
M8 and M10 are O-ring, but M6 seems to be resin color.
View detail
Bolt part to Custom
[How is it used?
License Plate Bolt to Custom
Was the one you received as per Image?
Yes, it was exactly what I expected.
How was your experience with it?
Bolt section is now custom made.
[Points to note] It takes a little time to install.
How did it compare to other products?
No comparison, so no.
Other items that would be helpful
None
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
When installing on CT110 HUNTER CUB, it seems to be easier to loosen the Rear Reflector, though.
View detail
Alternative to OEM Product!
When I took my NC750X out of Garage to wash it, I noticed that the Bolt on the Rear CarrierStay was missing.
It was not a place where you can easily remove it, and there were two places. I thought it might have been stolen, but I had to find a replacement. I was worried that it might be stolen, but I bought a replacement because it was not available.
View detail
For Dress-up
It is quite bright. Installation requires removal of the tail cowl, but it is not that difficult, so the difficulty level is not high.
The shape is the same as OEM, so Clearanceetc. had no problem.
View detail
Fits: KAWASAKI NINJA250R, KAWASAKI NINJA400
Ninja 400 with '23 MODEL
Installed on Ninja400/23 MODEL
The reason I replaced it was because with OEM, it was a hassle to be aware of every hand position when I held it back to turn it.
The scene used is Circuit.
I did it myself because of the high labor cost of working with Naps.
The Cowl and Tank were removed, Handlebar peripheral parts were removed, Accelerator Wire was replaced, etc., etc., etc., etc. The work was large and strange.
If you don't have the knowledge, you should never touch it yourself.
Please ask Motorcycle shop honestly.
The key impresion is that it is very good.
It is useful because it can be turned off firmly.
As a demerit, Axel is heavy.
Your hands will get tired if you are not used to it.
Drooping will also increase.
In SCENE that uses low speeds, such as traffic jams, be careful because if you accidentally turn it, it will be Large strange.
View detail
Loading Hook
A Loading Hook has been added for easy use of the Net to supplement the capacity of the Small TypeTank Bag. On the back side, a Loop is threaded through the Club bar.
I used the same Posh face colored Spool M8x30mm and Stainless bolt M8x120mm as the Loading Hook without any modification. I think a M8 x 25mm colored spool or a 1cm short Loading Hook would have been fine. However, in the case of the Short Hook, the inner diameter is too large to interfere with the Club bar, and a thin Hook made of gold might be better suited for this purpose.
View detail
For mounting of cargo hooks
I used it to attach the Loading Hook for easy use of the Net to supplement the capacity of the Small TypeTank Bag. On the back side, a Loop is threaded through the Club bar.
I used a loading hook M8 with the same posh face as the colored Spool and a Stainless bolt M8x120mm without any modification. I think a M8 x 25mm colored spool or a 1cm short Loading Hook would have been fine. However, in the case of the Short Hook, the inner diameter is too large to interfere with the Club bar, and a thin Hook made of gold might be better suited for this purpose.
View detail
Fits: HONDA NC700S, HONDA NC700X, HONDA integral, HONDA NC700S, HONDA NC700X, HONDA integral
value for money
After replacing the power supply plug, it can be installed on the NC750S Gen.1, and the quality of the entire vehicle is improved. Although the materials and workmanship are not as good as SP Wuchuan, the price is more reasonable and it is worth the money. It would be better if it has a blackened appearance and matches the original car turn signal. -------------------------------------------------- -------- After replacing the power supply plug, you can install it on the NC750S Gen.1, and the entire vehicle texture has improved. Although the workmanship is not as good as SP Wuchuan, the price is more reasonable than it, and it is worthwhile. If there is a better appearance, it is matched with the turning light of the original car. Powered by Google Translator View detail
Fits: KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI NINJA250R, KAWASAKI NINJA400R, KAWASAKI NINJA650, KAWASAKI NINJA650R, KAWASAKI Z750, KAWASAKI Z750S, KAWASAKI Z800, KAWASAKI ZEPHYR1100, KAWASAKI ZRX1100, KAWASAKI ZRX1200DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZX-7R, KAWASAKI ZX-9R, KAWASAKI ZX14R, KAWASAKI ZZR1100, KAWASAKI ZZR1200, KAWASAKI ZZR1400
Better than OEM
Vibration is reduced by being heavier than OEM.
Also, in the case of zx4r, with OEM, I was hearing a chattering sound from the Left Side, so that will be eliminated as well.
I wonder if the replacement product has a slight gap (see image).
View detail
Fits: KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI NINJA250R, KAWASAKI NINJA400R, KAWASAKI NINJA650, KAWASAKI NINJA650R, KAWASAKI Z750, KAWASAKI Z750S, KAWASAKI Z800, KAWASAKI ZEPHYR1100, KAWASAKI ZRX1100, KAWASAKI ZRX1200DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZX-7R, KAWASAKI ZX-9R, KAWASAKI ZX14R, KAWASAKI ZZR1100, KAWASAKI ZZR1200, KAWASAKI ZZR1400
Appearance ImpactLarge
It would have been best if the Mounting Bolt had a Screw lock agent. View detail
If Black!
It is used on brembo's Radial brake master 14RCS.
I bought a PLOT Tank BracketBPS002-BB at first, but the rubber hose was bent in the middle. I searched for a lot of information and came up with this product.
This product allows the S-15BTank to be fixed in an almost perfect position and angle, with a very natural bend in the rubber hose.
I have two complaints:I want a black color and the BoltM6×30mm is too short to install on the MASTERCylinder. It is not impossible to install the bolt, but it is necessary to replace it with M6×35mm bolt. (The photo is before replacement).
The color is simply my taste, but I have reduced one star because of the short Bolt.
View detail
For off-road motorcycle Mirror Hole Plug
Used for Mirror Hole Plug for off-road motorcycle.
I often remove Mirror when participating in Races, etc., and wanted to prevent mud, etc., from clogging it.
There are many inexpensive Color line nap products, so it would be useful to have a few.
View detail
Fits: KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI NINJA250R, KAWASAKI NINJA400R, KAWASAKI NINJA650, KAWASAKI NINJA650R, KAWASAKI Z750, KAWASAKI Z750S, KAWASAKI Z800, KAWASAKI ZEPHYR1100, KAWASAKI ZRX1100, KAWASAKI ZRX1200DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZX-7R, KAWASAKI ZX-9R, KAWASAKI ZX14R, KAWASAKI ZZR1100, KAWASAKI ZZR1200, KAWASAKI ZZR1400
Totally Match.
Match the Black/Silver body for a clean look.
The weight is a little heavier and although I haven't driven long distances, the vibration is reduced and it feels good!
View detail
Fits: YAMAHA MT-03, YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
It may be a little small.
It is a POSH product, so the texture is good, and the Anodized color is perfect.
However, it does not have much presence since it is a Large size and has been butchered.
I thought it was not suitable for those who want to stand out as Accent.
View detail