Reviews
It's faded.
Titanium Color:2pc. I bought a set, but the color is completely different from the same titanium color. Very slow response. View detail
Retighten your seatbelt before you go!
Because it was noticed at the traffic light, I replaced it. I put my favorite color on it and was satisfied with it, but when I was driving at night, I heard "KA-RAN! I was blown away! Cap? (Seal) Because the pitch rattling is bigger than the OEMCap, I will recommend you to tighten it before running the car View detail
Fits: YAMAHA MT-03, YAMAHA MT-25, YAMAHA N-MAX, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA NMAX155, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA NMAX155, YAMAHA YZF-R3
Garbage
Special shape that cannot be tightened with tools
The manufacturer's specification is to hand-tighten them, so I'm not expecting the use of tools But it's too painful to do with bare hands
To top it off, it flew away while driving
Engine oil was blowing and a lot of gold was lost with the first aid measures and so on
If you are considering purchasing, please consider it a Wiring requirement
Also, on the other hand, if it doesn't come loose and can't be removed, you can't use the tool
View detail
Fits: HONDA CBR600F, HONDA CBR600F, HONDA CBR600RR, HONDA CB1300SUPER BOLDOR, HONDA CB1300 SF, HONDA CB400SUPER BOLDOR, HONDA CB400SF, HONDA CBR1000RR, HONDA CBR954RRFire blade, HONDA VTR1000FVTR1000F FIRESTORM, HONDA VTR1000SP
Not bad
I put it on my CB400SF, the atmosphere is much different than the OEM and it was just like the image However, it is difficult for Valve to fit into the Bulb Socket and the Pin Size should be a little larger In addition, because the packing that removed OEM was degraded and could not be reused, Cover It would have been 5 stars if it had a packing In the end, I bought Repair Lens Packing Well, it is not bad View detail
Fits: KAWASAKI NINJA2 Helmet50RR, KAWASAKI NINJA250R, KAWASAKI Z250 (2013-)
Compatibility with OEMExhaust System ×
In the case of the OEM exhaust system, this part will interfere with the body without ABS Cannot be attached to Position 2 and 3
So I have no choice but to use it as Position 1, but the load may have changed If you can only use Position 1, it's hard to find a reason to install it
In general, I would recommend this product to anyone who has converted to a thin external exhaust system I felt it
View detail
The strength of resin Parts is not good
Screw receiving side fixing Lens (resin) It was weak, just being opened and closed a few times became stupid → To fix Lens with Vinyl Tape. Also, the part supporting the bulb (resin) Is poor, Fixing Screw is easy to relax → light bulb falls inside and Lens melts and deforms due to heat
... I liked it, but I only used about 2 months, I replaced it with KIJIMA.
View detail
Unlike Image
Together with the License frame it was not so good.
I just thought that I chose it by color, but I thought it would be more clear.
View detail
I removed it..
I also did impression last time, but I returned to OEM at a later date. Reason,
? Brake can not be used at startup and it is dangerous on a slope
? Right Taking care of separating hands (KICK repeats)
? OEM remains as easy to use
Based on Yamaha recommended starting method, although it is natural, OEM position is the easiest to use.
In extreme Up Handlebar or Separate handle, when priority is given to the angle of the Clutch lever, it may be difficult to use, Cable interferes and it is necessary to relocate Decompression,
I think that there is no need to relocate to save a single Cable.
Cable can be purchased on Wee Big. Exchange is also easy. Practice KICK without Decompression in preparation for when it runs out.
View detail
I'm sorry!
Engine warning lamp lights first around 100 km.
Limiter also worked.
It was cheap, so I did not expect so much, but it was more than I could imagine!
View detail
Price is too high
Is it more emphasis on fashion than functionality? Material is too soft.
Because it is a wider Minus groove, you can easily lick it when tightening with Driver.
I recommend you tighten it moderately with a 500 yen coin.
So it is better not to think of Bolt to install Brackets.
I thought that I wanted Material to be something like Stainless Steel and tighten at Hexagonal Wrench.
It is appreciated by Yamaha car User that there is reverse Screw type...
View detail
Fits: HONDA CBR600F, HONDA CB1300 Super Four, HONDA CB400 SUPER BOL D'OR, HONDA CB400 SUPER FOUR, HONDA CBR1000RR, HONDA CBR600F, HONDA CBR600RR, HONDA CBR954RRFire blade, HONDA VTR1000FVTR1000F FIRESTORM, HONDA VTR1000SP, HONDA CB1300 SUPER BOL D'OR, HONDA CB1300 SUPER BOL D'OR
Grinding with Grinder
Since it was written as CB 1300SB, I bought it, but in the Bordeaux of the 09 year model I grabbed Grinder and forcibly attached the place where the inside shape did not fit and became an obstruction.
It seems that water has not entered or taken off, so I will try to see how it is going - - -
View detail
Like another person
I purchased the shape well
Do you want to compromise just as good as heavier?
Do you want to replace it?
Approximately one week installing I think that it will probably be exchanged for another
View detail
weak
Motorcycle with a lot of vibration around Handlebar, but it broke in a few days.
Design is better than NISSINOEM but strength is too much.
It is better to improve the shape without removing the meat.
View detail
It is important to look
Shoes are damaged in only one place because the concentration point concentrates on a less effective point.
It is Parenthesis to the last ... But maybe you do not understand so much
I do not need two. Gold amount is a market if you consider shipping costs.
View detail
The word AISCancellation is a GunDam-like feeling ...
If you look at the word AISCancellation somehow Parenthesis is good ....
Well, the subject - After replacing the Exhaust System AfterFire sounds panpan, it is thought that this will be done by exchanging the Exhaust System. (I exchanged the past two Exhaust Systems, but after all it was out. )
Even if Jete Ing's adjustment is done, the frequency of AfterFire A will be a little better, so I tried Cancellation of AIS with a tough stance.
It definitely disappears, I thought that it would be about 300 yen in this Parts configuration as a product.
The installation comes with Instruction Manual, but it has surprisingly gone wrong. Work time is about 45 minutes, and it is hard to get out of Bolt kind ....
Also, I did not remove AIS quietly, it took a shape to cover the end of AIS, which is also a reason for the increase in working time.
If it is necessary to detach AIS secretly, it will be over in about half the time.
In other words, by biting the lid at the final part, the position of the Bolt part of each part shifted and it took time to cause it.
Conclusion, although it is the reason of 2 ☆, it will be the result of considering the price and instruction content and substitution.
☆ I made one more when Gasket was attached with this product.
View detail
I do not know.
Although it is before opening it has scratches like the view.
Worth 1,000 yen in 4 cases - - - How is that?
Bolgarage's Bolt cap is enough.
View detail
The quality is good - - -
Although it is sometimes called Posh made, it is not bad about the quality aspect, but because Screw 's adjustment range of the car body side has been made wider, the Screw will loosen only by fixing the Screw head alone.
I think that it is necessary to bite Rubber Bush as a countermeasure and make it harder to slip.
View detail
The color is different from the photo
Because it was cheap, buy it as Universal Colol which Iloilo can use. The color is different when it arrives. In the photograph it is pure white, but what I received is milk White color - - - The color is close to Beige.
I'd rather Black rather than White. As I saw it, it looks like a deteriorating color.
I will use it other than the visible part.
Just without BALI molding is nice.
View detail
Fits: KAWASAKI Z1000, KAWASAKI Z250, KAWASAKI Z800, KAWASAKI NINJA400R, KAWASAKI NINJA250R, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI ZX-6R, KAWASAKI ZrX1200ZrX1200 DAEG, KAWASAKI ZrX1200ZrX1200 DAEG, KAWASAKI Z800, KAWASAKI Z250, KAWASAKI Z1000
A little Imechen
I bought it for a little Imechen.
Just to remove the screw and install it
The gap opens and it does not attach firmly (Molding required)
Because it is a consolidated price, I will return it and replace it, so I will mold it and attach it.
View detail
Fits: KAWASAKI Zephyr 750, KAWASAKI Zephyr X, KAWASAKI Zephyr 400, KAWASAKI Zephyr 1100, KAWASAKI Zephyr 750, KAWASAKI Zephyr X, KAWASAKI Zephyr 400, KAWASAKI Zephyr 1100
Regrettably it seldom changes at about 10 mm.It is Ok if it thinks that mere a few is also.Attachment is very easy.I think with appearance that it is good.
Regrettably it seldom changes at about 10 mm.It is Ok if it thinks that mere a few is also.Attachment is very easy.I think with appearance that it is good. View detail