Reviews
It gives a nice Retro feel.
It was inexpensive, easy to install, and gave a nice Retro feel.
I wonder if old Motorcycles had them.
There was just a little left over after one round of Fuel Tank.
View detail
Bolt replacement in prominent areas allows you to use it without worrying about Rust!
[How is it used?
I purchased this to replace the Fender mounted Bolt on the Front fork.
Was the one you received as per Image?
It was shiny and high quality, just like the Image.
Was the installation difficult?
It can be easily installed by simply replacing the Bolt with a NORMAL Bolt.
How was your experience with it?
It can be used without worrying about Rust.
It is also shiny, though not as shiny as Plating, and good for the price.
[Included Parts:were they on?
No other than Bolt.
[Was there anything that disappointed you?
Not particularly
We do not recommend this because we are afraid of gnawing on the area where the heat is applied.
I appreciate the wide variety of lineups, such as ▼length and large size.
View detail
Made of Stainless steel, you can use it without worrying about Rust!
[How is it used?
By replacing the Front Fender, the Steel Bolt was replaced with a durable Stainless Bolt.
Was the one you received as per Image?
The quality was as high as the Image.
Was the installation difficult?
Bolt replacement for easy installation.
How was your experience with it?
It will be used for a long time without worrying about Rust.
The Button bolt looks more expensive than the Cap bolt.
[Included Parts:were they on?
Nothing else is included.
[Was there anything that disappointed you?
Not particularly
▼Quantity:It would be even better if there is a Package that comes together as a Set product.
View detail
Alternative to OEM Product!
When I took my NC750X out of Garage to wash it, I noticed that the Bolt on the Rear CarrierStay was missing.
It was not a place where you can easily remove it, and there were two places. I thought it might have been stolen, but I had to find a replacement. I was worried that it might be stolen, but I bought a replacement because it was not available.
View detail
Cost performance is the best
I bought K&N for the air cleaner, but I thought that the BreatherFilter did not need to be wet type, so I bought this one. View detail
Cap bolt is also a Quantity:Set product.
[How is it used?
I purchased this product because I wanted to replace the bolt for fixing the exterior of the head, which had become licked as I repeatedly took it off and on.
Color and Cap bolt are Quantity:It is convenient to say it is convenient because it is a Set.
Was the one you received as per Image?
Standard for this type of aluminum spacer. FUJI TUBO type. The product was just as beautiful as the image on Webike's website, and it was exactly as shown in the image, without the uneven staining that is common in low-priced aluminum collars from other companies.
Was the installation difficult?
There is nothing difficult about this product, as it is installed by biting it in place of a washer when using a cap bolt.
How was your experience with it?
Since it is made of aluminum material, each piece is light in weight and can also serve as a washer, making it a very convenient product that can be used in a wide range of applications.
One point can be used to attach a License Plate or to fix an accent to the exterior of the body, which is somewhat plain on the BoltSingle Body.
It is not lightweight, reinforced, etc. (strictly speaking, there is a slight increase in color), and it costs a lot of money, but I like this kind of product, and I am very grateful for it.
The appearance is that of the FUJI TSUBO Type Design from a generation ago, so in the age of 2025 Fashion!" I'm not a middle-aged person, but I'm not a trendy middle-aged person.
[Included Parts:were they on?
Normally, only the aluminum collar is sold for this type of product, but this product includes the cap bolt as well as the quantity.:It is a set, so the price is not cheap, but it is easy to use.
[Was there anything that disappointed you?
If you like the design as shown in Webike's image, you can buy it. Disappointing. It is lightweight enough.
Make good use of the wide selection of 11 colors to add flair to the Accent of your car body.
Other items that would be helpful
Point and hang of installation
As mentioned above, it is like a fashion color used in place of a bolt washer, so it is a simple job to use the Barnacle Collar when attaching a cap bolt of the appropriate length to the bolt stop on the attachable part.
[Availability and clarity of the Instruction Manual
No Instruction Manual is available
The ease of understanding is at the top level, so I don't think that wrong usage is likely to occur (unless you get twisted and use it in a different way on purpose).
[Notes]
None in particular, in Color variations. The color tones are different from what I saw in the picture." There may be some things that are not so common in motorcycle accessory stores anymore, but that may not be a problem.
[ITEMS TO BUY TOGETHER
Cap bolt and color are Quantity:However, if you wish to use it for fixing numbers, etc., please purchase the required number of M6 size washers and nuts for the reverse side separately.
[Opinions and requests to Manufacturer
Please make the price a little lower so that I can easily purchase large quantities.
View detail
It's bigger than I thought
There are also high-priced Knn filters, The posh is well made for the price. It's satisfying. I'm planning to buy it again next time. View detail
Good variety of Sizes.
I went to Home center first because it was hard to find this kind of product on webike, but I couldn't find one with the same shape as the OEM one, and the ones I could use were too cumbersome because they required some modification. I went to Home center first, but they had a hard time finding the same shape as the OEM one, and even if they did, it would require some modification, so I gave up. The product is the same shape as the OEM and the size is JUST right! The only thing is that the price is a little bit high. View detail
Recommended!
Recommended!
Custom feeling goes up!
View detail
Decompression is a must for a long ride.
I was able to start the engine without Decompression for a while without any problem, but it became hard due to my age, so I added Decompression again.
youthful indiscretion No Decompression cable! I threw it away and, and, I bought it.
What is Decompression anyway?
"Pull the compression, lose it." When the pressure in the cylinder increases during the compression process at kick start, pulling the compression lever opens the exhaust valve slightly to release the compression pressure. Therefore, the Kick Arm is lightly depressed and the engine is ready to start. "Position past the compression step." It will be possible to let out the Then release Lever and step through the Kick Arm from the uppermost to the last with vigor, and you can easily start the Engine.
After all, even if the engine can be started without decompression by brute force, it is still a good idea, since it places a large load not only on leg strength and labor, but also on the Kick Arm and related mechanisms.
good point
Durable as ○OEM.
○ Easier to obtain than OEM.
○Easy to start the Engine because Decompression is available. The foot doesn't get tired.
○Cable and length are both practical lengths, so it can be used as long as it is not a Separate handle or extreme Handlebar Up Type.
A bad point
It's a hassle to install.
By the way, the installation procedure is
(1) Attach Decompression lever to Holder.
(2) Attach Wire to Decompression lever.
(3) Attach Wire to the Engine side 。
Tighten the play adjustment section of ?Wire.
Note that the Screw near the Tappet of the Engine in (2) is easy to lick.
Even if you step down once on the kick starter, the crankshaft only turns one revolution plus α. However, the 4StrokeEngine explodes once per 2 revolutions of the crankshaft, so it is necessary to step down from a place with good timing where the engine is easily activated. 。 You can easily step on the KICK by removing the compression! That's the situation. [Color] Clear is Decompression.
Ketin." This avoids the RISK of hurting your feet due to the repulsive action called
View detail
Black stainless
The Fixing Screw is replaced with this stainless black one to make it less conspicuous, since a regular stainless steel one would stand out.
It was helpful to have a choice of Size and type.
View detail
Fits: YAMAHA TW225E, YAMAHA SR400, YAMAHA SR500, YAMAHA TW200, YAMAHA TW200
Best if you don't care about the brand.
I usually use K&N, but I use it as an alternative during maintenance.
Power Filters are available from various places, and I have used many, but I think POSH's is relatively good.
good point
The ○Cleaner capacity is also quite large, so the intake efficiency is good.
Filter clogging is less likely to occur compared to other companies' filters.
○K&N's maintenance kit can be used here. 。
It will run without changing the Carburetor setting from when the XXK&N. → that is, high performance.
○ Inexpensive and good performance.
A bad point
I don't think so.
Certainly K&N has high performance, but it also has BrandImage, if anything, and I think that is reflected in the price.
If you are not that particular and want to improve performance, this product is a recommendation.
View detail
Black
I purchased this product to unify the fixed parts in Black.
The rust-resistant stainless steel and black color are inconspicuous, and the color unifies the product and gives it a nice look.
View detail
Stainless black
I bought this stainless black to replace the stainless bolt fixing screw, because the silver bolt stands out and the balance of the color is not good.
It matches the rest of the Black and is less noticeable, so I am happy with it.
View detail
Fits: YAMAHA XJR400, YAMAHA XJR400R, YAMAHA XJR400, YAMAHA XJR1200, YAMAHA XJR1300, YAMAHA FZ400
It was old and didn't move well.
I bought it used, so I was inspecting a lot of things.
It was a little stuck, so I replaced it.
The return is faster and more comfortable.
View detail
Stainless Steel
Change to Stainless capFixing Screw to prevent rusting.
There are no varieties or sizes nearby, and this place has a wide variety of products.
View detail
Fits: HONDA NSR250R, HONDA RC45, HONDA RC30, HONDA NC35, HONDA NC30, HONDA RC45, HONDA RC30, HONDA NC35, HONDA NC30
big
Different size, but used on ZX10R.
Spec. 30mm, while 10R is 32mm, so it will come off easily as it is.
I put it on and hit it with Hammer and it deformed nice.
It may be bigger and uglier than expected, but when I ordered a Universal Product for 32mm, I received a monstrous pin about the size of a smartphone, so this is my only choice.
View detail
Almost OEM
In SR's case, the OEM's mall is halfway between
Only length is available. Sober Parts
However, it is necessary to properly use the Seat.
Since it is possible to cover up to
It is surprisingly Recommendation. Installation is
Rubber hammer as it can be slightly stiff.
without having to remove the Tank if the
It can be installed cleanly to some extent.
SR is 2m with a little extra.
Both Sides has a slightly exposed portion of the genus Gold.
before installation as it may cause rust.
You can cut off a little bit of both ends.
View detail
Fits: YAMAHA TW225E, YAMAHA SR400, YAMAHA SR500, YAMAHA TW200, YAMAHA TW200
Is this what it looks like?
The thing itself is good, like Design and Included Parts:.
However, the tightening Band is hard to use.
As the carburetor would fall out of the carburetor when tightened, we extended the carburetor using the OEMAir cleaner hose.
View detail
Fits: KAWASAKI Universal, KAWASAKI Universal
Quantity:1 Set for 1 Vehicle
Used on W650, sticks in Female side OEM with no problem. Even if it fails, it can still be used with Quantity:2pc. It is safe to say that there is a surplus of Set w View detail