Reviews
Used as Bracket for Switch on Grip heater
The Bracket that was originally attached was too long and was bent at the Prank, breaking it off at the base.
This time, I don't think it will be tampered with because the base LARGE size and height of the base are just right and not uncomfortable.
View detail
Compact Cargo Hook
It does not protrude more than the Clubba and fits better. The Net Hook should be more compact to fit in the case of the Clubba. I used the same Posh face color SpoolM8x30mm and Stainless boltM8x105mm. View detail
Loading Hook
A Loading Hook has been added for easy use of the Net to supplement the capacity of the Small TypeTank Bag. On the back side, a Loop is threaded through the Club bar.
I used the same Posh face colored Spool M8x30mm and Stainless bolt M8x120mm as the Loading Hook without any modification. I think a M8 x 25mm colored spool or a 1cm short Loading Hook would have been fine. However, in the case of the Short Hook, the inner diameter is too large to interfere with the Club bar, and a thin Hook made of gold might be better suited for this purpose.
View detail
I am concerned about Bolt's Size.
Here are my impressions after installing on a Triumph SpeedTWIN1200.
Since there was no place where a Net could be attached, it was installed in the form of replacing the Bolt on the Rear suspension.
The work was easy and securely installed, and the Net is now ready for use.
Also, the texture is adequate for the price.
I bought Black, and if I wanted, I would be happy if the center Bolt was also Black.
Bolt size was a concern during installation.
The length was fine, but the diameter was slightly smaller than M8, and I was a bit concerned about the possibility of the mountains licking if I tightened the screws too hard.
(It may be correct to say that the Frame side may be just slightly larger than the M8, so it is not an outstanding match when installed on SpeedTWIN.)
I'm generally satisfied.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Installation is easy
There is nothing difficult about the installation.
Before the work, the tank is cured with a thick toweletc. to prevent wounds.
(It's just a small step to avoid the extra time, effort, and expense.)
1.Temporarily assemble the Mount Bar and Mount Bracket.
2.BoltQuantity near the tank of the Handlebar Holder:Remove 2pcs.
3.Assembled the collar, temporarily assembled Mount Bar + Mount Bracket, Flat Washer, and M8x45Cap bolt to the car body in this order.
4.Temporarily tighten Bolt on each part
5.Bolt tightening in each part
This completes the process, but there is one point to note.
Tightening torque for M8x45 cap bolt. The specified tightening torque in the Instruction Manual for the product is 30 N・m, and the same value is given in the Service Manual. However, do not tighten the bolt all at once, but tighten it while observing the situation.
The tank-side joint surface of the upper handlebar holder has a gap with the tank-side joint surface of the lower holder. Since the upper holder is cast aluminum, it may break when tightened in overtorque.
The appropriate tightening torque varies depending on the bolt material, strength, material to be fastened, required fastening force (axial force), etc. Of course, there are standard tightening torques. Of course, there is a standard torque for fastening.
Since this is an important part of the steering, we recommend the use of proper fastening tools and not relying on intuition as much as possible.
The same situation may not apply to other vehicles of the same model and year.
To be sure, we checked the torque of the Handlebar Holder Fixing Bolt on the actual vehicle before disassembling.
All four were 20 N・m without lubrication. The target for Torque tightening was 20 Nm.
In the photo, both the cap bolt and button cap bolt are black.
This is because we changed the color when we changed to the same material as the OEM Handlebar Holder Fixed Bolt.
The OEM Bolt is SCM435 (10.9T) trivalent ChromateWhite.
The Bolt in the photo is SCM435 (10.9T) trivalent ChromateBlack.
View detail
Sakka who surely saw as other impression -- custom . although it is slightly high -- a design -- good -- I consider. It is a recommend at those who want to change appearance!!!
Sakka who surely saw as other impression -- custom .
although it is slightly high -- a design -- good -- I consider.
It is a recommend at those who want to change appearance!!!
View detail
Not used, but definitely stands out.
[How is it used?
In my case, I am converting to Single Seat, so I do not use Net Anchor. It is completely decorative.
Was the one you received as per Image?
Lightweight and textured as expected.
Was the installation difficult?
Simply replace with OEM. Anyone with a tool can replace it.
How was your experience with it?
I haven't used it, but I don't think it's a problem.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
Other items that would be helpful
Point and hang of installation
It is better to check the installation torque. In my case, I tightened it too much and the single seat cowl did not fit well (because the rear cowl was twisted?). I think people who have GSX1300R HAYABUSASingle seat cowl can understand this.
[With or without Instruction Manual
Posh, so a simple Instruction Manual is available. Anyone can install it.
View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja 250, KAWASAKI Ninja 400 (2014-), KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3
When attaching a Bracket to a Motorcycle with a Separate handle
[How is it used?
Used to mount the Smartphone Mount on the Separate Handlebars of Ninja 400.
Was the installation difficult?
On the Ninja 400, there is an unused screw hole in the clutch lever that can be fitted in a matter of seconds if you have a Hexagonal Wrench.
How was your experience with it?
This is the only bracket that requires a screw hole conversion adapter.
I think it is good to be able to choose your favorite color because there is a color development.
[Was there anything that disappointed you?
The Handlebar area is a bit cluttered, as is the rest of the Bracket and the Multi Bar, and it's quite noticeable when you're trying to mount your phone from the Bracket.
View detail
Used for Temp meter installation
I installed it on the LeftHandlebar side of GSX1300R HAYABUSA.
I think it's great because it locks you firmly into a position you can easily see!
The Temp meter is on the top, and the Button for the Drarecorder is on the front, I think it will be neatly organized.
As far as I'm concerned, …
If the display instruments are installed on the top surface, they may be angled and difficult to see depending on the type of vehicle and the body shape of the passengers.
Also, in the case of the GSX1300R Hayabusa, the window of the clutch reservoir tank is hidden and difficult to see.
View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja 250, KAWASAKI Ninja 400 (2014-), KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3
The texture is rather good.
I bought this to fix my Smartphone Holder to my Motorcycle.
Functionality
The Bracket is basically used in conjunction with the Mirror to hold the Smartphone Holder in place.
It is very rigid and can fix the phone holder very firmly. If the bracket is too soft, the screen will be blurred, so it's a very important point. However, the angle of the bracket is twisted so that the round bar is at a good angle, but depending on the angle of the handlebar on the car body, the round bar is not level.
■ Design
Round bars are Material:The color can be selected by Aluminum, so it is easy to match with the body color.
The Bracket part is made of steel, but it is finished with thick black paint, so it blends in with Mirror mount & Switch box without any sense of discomfort.
General Comment
The angle of the bracket can be adjusted by the user, but this is not an option. I'm not sure how much rust resistance it has because the bracket is made of iron.
If you have a cowl car, etc., if there is a place where you can fix something near the meter, you can install the smartphone in a place where there is little eye movement, which is ideal.
View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja 400 (2014-), KAWASAKI Ninja 250, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3
It's not quite what I imagined it would be.
BANDIT250 (gj74a) The LeftMirror installation part is made for the smartphone holder.
Overall, it's good, but the angle of the bracket part is shallower than I expected and it's a pain to install.
It's only a personal installation issue, so I'm not too concerned about it.
The car is currently sitting at home as it was scrapped in an accident.
View detail
Fits: YAMAHA YZF-R25, KAWASAKI Ninja 400 (2014-), KAWASAKI Ninja 250, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3, KAWASAKI Z900RS, YAMAHA MT-09, YAMAHA YZF-R3
The bolts that come with it are easily rusted
I am satisfied with the installation and shape
However, I recommend you to buy SUSBlack because the included Bolt washer is easily rusted Recommendation
View detail
Slider replacement
I installed it because I thought it was lonely with the Stand Hook hole, a common 10 for the 6R note that this is an 8mm Stand Hook hole, not amm hole
Our Parts were scraped off when it fell over, but there was not a scratch on the Swing Arm I feel glad I installed it
View detail
I am useful.
SEROW's Adventure Carrier's Frame is too fat,
Net or code hook is not applied.
OEM Product is so expensive that it's OK with that.
View detail
CB400SF (MC42) It fits perfectly.
There is a storage space of the same size as the product outer dimension in the MC 42.
Does Honda contact DAYTONA? It fits perfectly.
The box itself is firmly made with a simple drip-proof feeling.
The point of discontent is that the Indicator of the COCOSECOM terminal that pays
Very hard to see. Once you install the Indicator to the outside,
It is a bit unkind since it is only notification of the condition of the Red color LED blinking.
It is expensive, but this is inconceivable feeling considering production number and product making.
View detail
Completely clean
Perfect for JRM-11 made by Japan Radio.
Tighten to Clutch lever holder.
Just because it is too conspicuous, I'm considering moving it around Meter.
View detail
It is a good deal..
I think that the usability is good because it is lightweight and it can adjust the angle.
However, angle adjustment many times (Bending elongation) Then, the surface Anodized (?) It seems Crack is in.
The hole of M6 mm is empty because it is used for fastening with the Clutch lever holder, but if it is 8 mm it can be installed anywhere..
I am satisfied because it is inexpensive compared with similar products of other companies.
View detail
Buy without loss
I bought it in preparation for Hokkaido Touring.
It is used as Loading Hook in the License Plate to raise the loading capacity.
With this, it is now possible to tie baggage to the extent that Tail lamp is not hidden on Rear Fender.
I also feel like playing a part in Dress-up style.
However, I think whether it is a little expensive personally.
It is not something to make tens of thousands of yen ^ ^;
View detail
It is convenient to have it
I bought DOrange, but because there was some red color and the color tone did not match, I used it painted in Orange color.
Easy to install, easy to use.
View detail
To ensure unity
I was hooked in Bolt hole of Tandem Footpeg when hanging Net on my luggage
I purchased it because I burned my finger at the base of Silencer when I removed it
By attaching it, you can surely shorten the time required for packing
I think that it will become Dress-up as rich lineup of colors is also available
View detail