Reviews
Bolt part to Custom
[How is it used?
License Plate Bolt to Custom
Was the one you received as per Image?
Yes, it was exactly what I expected.
How was your experience with it?
Bolt section is now custom made.
[Points to note] It takes a little time to install.
How did it compare to other products?
No comparison, so no.
Other items that would be helpful
None
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
When installing on CT110 HUNTER CUB, it seems to be easier to loosen the Rear Reflector, though.
View detail
For Customization around License Plate
I have been using it for a long time for customization and to prevent cracks from entering the License Plate hole since it holds a wide range of License Plate holes.
(The models in the photo are 2022 RIEJU MR250 Racing and Tango250 because they were the only choices available in the system.)
View detail
Compliance with new regulations provides peace of mind
Due to changes in the law, the installation method used to be [Color] Since I could not clear it, I purchased a POSH License Plate Holder and a Number Fixing Bolt. This will help me to comply with the stricter labeling rules. [Color] The number fits nicely without any fluttering, and the dress-up effect is outstanding despite being a simple part. View detail
New regulation compliant product
Strict License Plate Labeling Rules Made Stricter by Revised Laws [Color] The clear surface gives a sense of security. It is a simple part, but it also has an outstanding dress-up effect. I recommend this product. View detail
Mounted on Large-type car Number
I installed it on my CB1300SB. The length of the License Plate Bolt is limited because of the Camera Holder.
Also, I think it depends on the NanBar size, but the corners interfere a bit.
View detail
It can be used in many ways.
The anodized gold color gives it a luxurious feel and makes it a wallet-friendly product for one-point customization. View detail
Red
I was using a Type with nails under the POSH, but it didn't fit well and the License Plate was floating.
I replaced it with this one.
View detail
Buy first when you buy Motorcycle!
I buy this product every time I change my Motorcycle.
I like the shape better than other companies.
Anodized is also beautiful and has been used for a long time.
View detail
Dress-up!
I installed it on the Dress-up of License Plate Bolt.
However, if the laws and regulations regarding Number change in the future, Color:It could be a GrayZone, so be careful!
View detail
I'm mostly satisfied
Fitting with the License Plate is good with almost no extra white parts.
However, the beveling on the edge of the Plate is a little rough.
Also, it can't be helped, but there are some distortions on the 6 curved surfaces around the Plate because of the PRESS processing.
The contact surface with the License Plate is Flat.
View detail
It's for decoration.
When I bought the motorcycle, I left the number with the motorcycle shop, but when I installed it and delivered the car, I tightened the bolt too much and the license plate was deformed, so I bought it to hide it.
It's just One pointAccent.
View detail
Dress-up of Handlebar area
I used it for the Bolt that holds the Bracket of the Controller of the Drraco instead of the License Plate.
It's a great way to dress up an otherwise bland bolt and improve the texture around the handlebar.
I didn't need the Bolt that came with it, I feel it would be better if the Cap bolt holder was sold Rose.
(Holder Single Body is Quantity:There are 1 Set of 4pcs.:2pc. I only need Set)
View detail
The rear area becomes gorgeous.
It's a simple customization that makes it look gorgeous with just a change in the license plate mounting bolts. View detail
It's definitely fashionable.
It's a great way to dress-up casually at One Point.
But this price is so high!
Well, it's not a product that's out of shape or anything, so if it's cheap on sale or something, I'd buy it.
View detail
It's stronger than I thought
I bought it to prevent Number cracking
It's rather thicker than the Image seen in the photo and has Rib, so it's quite stiff
I thought to install it with sponge on the back of Number, but there was no gap and it was impossible
It's a pretty tight fit
I hope this doesn't crack Number …
View detail
Bolt is a bit short
What made you decide to buy? It's another product, but I took the opportunity to install the Plate hook to get a little ime-Chain The fact that it was lined up in my beloved KTM color, Orange, was also a deciding factor
How was your experience with it? The color is a bit different from KTMOrange, but I'm mostly satisfied It's not overly assertive, but it's just a good pair of rare accessory parts
Was the installation difficult? Because the attached Bolt is 15mm, it is suitable if you just fix the License Plate However, when it comes to fasten something like Plate hook together, I procure the Bolt of 20mm and fix the License Plate with the Bolt of 20mm You have to be able to install it The difficulty of the installation itself is very easy
【Please tell me the installation point and hang】 To prevent the License Plate from tilting, you can use the proper Quantity:Pair (for Left and Right) Balance and tighten the Bolt while considering the balance of the
[Was there anything that disappointed you? As mentioned above, this is the length of the Bolt I'd like to see 20mm enclosed for expansion Well, I know before I bought it, so I'm " disappointed " or rather, I'm not expecting it itself I don't have one, but …
Do you have any wishes or improvements you would like to make for the Manufacturer? Bolt。
[Do you have any products to compare it to? There are many similar products
[Others] It's a good product with plenty of color variations, despite what you might say
View detail
By all means, put it on right after you get Number
The Right Side of the License Plate is stained with exhaust gas and it's about 10 months old I bought it now
There is also a type with a claw on the bottom side, but if you choose this type somehow & hELLIP;
Number was a bit curved and the gap between it and the Plate was flapping!
I bent and reassembled the Number, but it's still best to put it on right after you get it
View detail
No problem
For the past, we have a License plate attached to every single car!
It's easy to install, it will also be Dress-up
There is no breakage of the License Plate by vibration during running
I use it for ESTRELLAFinal
View detail
Many Color variations are recommended
It is a replacement from DAYTONAPREMIUM ZONE NumberHolder set.
Because the car was Green Light at Kawasaki, I used Green Light from DAYTONA, but I was looking for Titanium color thought that it was a bit flashy because the color was bright.
It looks a little Brown series? Color, but Titanium color is not too flashy and it feels nice ^ ^
View detail
Items to install first
Since the License Plate is peeling off unlike a car, Motorcycle purchased a License plate for protection. Because we have plenty of colors, choose Plating according to the car body
To install it, superimpose License Plate on License plate and just tighten Bolt together OK. Since it is a special item for Mini bike, the size of License Plate is Exactly, there is no Wobble even when running.
There are two things to watch out for in the License Plate of Mini bike, there are two types of squares and Yamagata, so please make sure when purchasing. Size is different for square and mountain shape, so you can not install it if you make a mistake
In addition to protecting the License Plate, as there is no dirt prevention, better appearance and no bad thing, we recommend installing it at the same time as purchasing Motorcycle
View detail