Reviews
I am satisfied!
[K-KON Pro I purchased and installed it together with KITACO License Plate Base.
I thought this product might not be cosmetic (a little expensive for a small parts product), but I bought it simply as a dress-up.
Installation is ELIMINATORSE (2023). It is extremely easy to unscrew and attach, and no special skills are required as long as you have tools.
In my case, however, I was a bit disappointed.
One Point that needs attention ….
Due to the thickness of the License Plate Base and perhaps the thickness of the bracket for installation of the DriveRecorder, the supplied 15mm bolt was too short and could not be reached. (Note that this product does not come with a nut, but an existing one can be used.)
I hurriedly purchased two Hexagon Socket tight BoltM6×25mm, the same type but 10mm longer, at Home center for @80 yen×2pcs.
Although it did not result in a large incident, such action is necessary, so as a preliminary knowledge, please be careful.
I am satisfied with the product.
View detail
POSH Aluminum Pillion Belt Cover
About quality and texture Well made aluminum from POSH. The cover gives a beautiful outlook compared to the stock sliver look. About the feeling of use It's a cover that fit perfectly without any lapse in space. Difficulty of installation Less than 15 mins to remove the original screw and place the cover on with the given screws. I hand tighten the the screws as hard as possible. Cost performance and comparison with other products There's no comparison with others as there isn't any similar product around. The price is not expensive but it gives an additional look in your plain looking seat. About shipping and packaging Shipping is not expensive as the the items are small. Items are place in a vinyl plastic bag but no visible damage after shipping. Any concerns, cautions, or advice when purchasing The given screws length is long enough as there's worries about the safety of the belt if the pillon is to grab it. Make sure it's well tightened and theses should not be a problem. View detail
Small size is the reason for rust resistanceMaterial:Stainless Steel Screw!
[How is it used?
Replaced the brake hose guide with an external aluminum guide.:Replaced with Stainless Steel.
Was the one you received as per Image?
It is as accurate and clean as the Image.
Was the installation difficult?
Easy installation by simply replacing it.
How was your experience with it?
It can be used without worrying about Rust.
[Included Parts:were they on?
Screw only, nothing else is included.
[Was there anything that disappointed you?
Not particularly
▼Quantity since wdisc.:Pair (for Left and Right) Four bottles are required in the following table.
View detail
Cowl stop.
The 900SS has a spacer and bolt that fly out of place due to vibration, and the front cowl that holds the spacer in place needs to be mass-tightened regularly as the bolt will loosen if you are not careful. Posh rubber is similar to the OEM product and I think the quality is even better. View detail
It is surprisingly noticeable when you put it on, which is good.
Used 4 pieces for Handlebar Clamp on XSR900.
The price is a little high, though, as it is a place that is always in view while driving, so it is highly satisfactory.
We were lucky to have a Gold similar to Fork.
M8 is with O-ring.
I found out when I put it on that I can see the silver color of the Bolt. I am satisfied with it because I can't see it while driving.
View detail
Looking for ways to use it.
I was going to use it for a Handlebar Clamp on my XSR900, but it was not available in this size, so I ended up buying it in vain.
I ended up buying M6, M8, and M10, all of which are of good quality and may not be as expensive as they should be.
I've seen some of these products not match the color when you buy them, but the gold of this series is similar to the gold of the XSR900's Fork.
M8 and M10 are O-rings. We will keep them until we can find a use for them.
View detail
It looks surprisingly different and good.
XSRLogoQuantity under XSR900 Meter:Pair (for Left and Right) Used for
The price is a little high, though, as it is a place that is always in view while driving, so it is highly satisfactory.
We were lucky to have a Gold similar to Fork.
M8 and M10 are O-ring, but M6 seems to be resin color.
View detail
Bolt part to Custom
[How is it used?
License Plate Bolt to Custom
Was the one you received as per Image?
Yes, it was exactly what I expected.
How was your experience with it?
Bolt section is now custom made.
[Points to note] It takes a little time to install.
How did it compare to other products?
No comparison, so no.
Other items that would be helpful
None
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
When installing on CT110 HUNTER CUB, it seems to be easier to loosen the Rear Reflector, though.
View detail
For mounting of cargo hooks
I used it to attach the Loading Hook for easy use of the Net to supplement the capacity of the Small TypeTank Bag. On the back side, a Loop is threaded through the Club bar.
I used a loading hook M8 with the same posh face as the colored Spool and a Stainless bolt M8x120mm without any modification. I think a M8 x 25mm colored spool or a 1cm short Loading Hook would have been fine. However, in the case of the Short Hook, the inner diameter is too large to interfere with the Club bar, and a thin Hook made of gold might be better suited for this purpose.
View detail
Fits: KAWASAKI ZZR1100/ZX-11, KAWASAKI ZRX1200S, KAWASAKI ZRX1200R, KAWASAKI ZRX1100, KAWASAKI ZRX1100II
Standard classic
Was the one you received as per Image?
As per Image.
Was the installation difficult?
It's easy
How was your experience with it?
Looks cool.
View detail
Is it sensitive to ultraviolet rays?
I put it in a Screen Fixing Screw, but I found cracks on 3 out of 6 screws, perhaps due to UV exposure, so I bought it for replacement. I have no problem with the quality if I consider it as a consumable product.
This time I bought it at the same time with Seat Cowl and for Side Cover for 6Millimeter screw.
View detail
It's degrading
I put it in the Screw of Seat Cowl and Side Cover to prevent vibration, but I bought it for replacement because there was a cracked part after about 2 years due to deterioration.
Since it is polycarbonate, I think it is necessary to be careful about cracks caused by over-tightening.
View detail
For fine tuning
Used to compensate for Cowl Bracket Gap in combination with other thicknesses of Spacer View detail
Spacer
Purchased to fine-tune the standing width between the Screen and the Screen stay. View detail
uplift
It is used to create an angle between the Screen stay and the Screen. It is black, the same color as the Bracket, so it does not stand out and is unobtrusive. View detail
Purchased for Bolt dropout prevention
[How is it used?
Purchased for Bolt dropout prevention
Was the one you received as per Image?
Yes
Was the installation difficult?
Easy
How was your experience with it?
I'm worried if I don't see them regularly.
[Included Parts:were they on?
(after the -te form of a verb) not ..
[Was there anything that disappointed you?
I wish it was a little stiffer.
View detail
On my friend's 12R A1.
I bought this to fix a friend's Upper CowlScreen on his ZX12R A1.
[Color] I was satisfied with Clear because it was less noticeable.
Since this is a polycarbonate Screw/Nut, care must be taken not to damage it by over-tightening.
View detail
Screen stop
Bolts to stop Screen.
Not very good looking.
View detail
Expensive but worth it!
[How is it used?
OEM Washer Rustetc. Rustproof Material as Repair Parts as it deteriorates over time.:I changed it to Stainless Steel.
Was the one you received as per Image?
High Quality and Rust-Free!
Was the installation difficult?
It is easy to replace an old Washer.
How was your experience with it?
You can use it without worrying about Rust as well as Nut.
[Included Parts:were they on?
Nothing else is attached as shown in the image.
[Was there anything that disappointed you?
Expensive is a regrettable Point in Neck.
I am not sure if they are not sold in Single Item, but I have a mid-Quantity:It is subtle that you have purchased 1 Set of 3pcs.
View detail
For Customization around License Plate
I have been using it for a long time for customization and to prevent cracks from entering the License Plate hole since it holds a wide range of License Plate holes.
(The models in the photo are 2022 RIEJU MR250 Racing and Tango250 because they were the only choices available in the system.)
View detail