Reviews
inconspicuous (Compliment.)
The quality is high!
I chose Black to give a sense of unity, but with this size, you may want to use a flashy color as an accent color.
The price is for one, so I think it is a little expensive, but I am satisfied with it.
View detail
inconspicuous (Compliment.)
Perfect Fitting View detail
Mirror Hole Cap
I bought this to hide the Mirror hall as I changed my CB223S to a Bar end mirror.
Note that the quantity is 1 pc.
If you value cosmetics, you can use Homsen Screws or Vinite.
The texture is good
View detail
For off-road motorcycle Mirror Hole Plug
Used for Mirror Hole Plug for off-road motorcycle.
I often remove Mirror when participating in Races, etc., and wanted to prevent mud, etc., from clogging it.
There are many inexpensive Color line nap products, so it would be useful to have a few.
View detail
When replacing the bar end mirror, please be sure to
Among the so-called reverse Screw type, I think this product has a good balance of texture and cost.
I have been using Spacer on the OEM Bolt since I replaced it with the bar end mirror, but I ordered it while I was ordering some things.
I am satisfied with the total because it looks neat and the color gives it Accent.
However, since the material is soft like aluminum, it is necessary to select the size of the driver carefully and dustcloth is essential.
View detail
water (esp. cool, fresh water, e.g. drinking water)
I bought this because I didn't want water or dust to get into the Mirror bolt when replacing OEM Mirror.
They blindfolded me nicely.
View detail
I changed it at One point.
I changed it at One point and became Accent and I like it. View detail
Due to the change in Mirror location
The Mirror hall was left open to allow water to accumulate, so it was plugged up.
Material is weak, so care should be taken when tightening it.
View detail
Detachable Cover Cap
I bought this to plug the mounting screw holes for the Back Mirror on my KLX125.
I often go to forest roads with KLX, not only open forest roads, but also many attack type forest roads, and sometimes I hit trees with Normal Back Mirror. Therefore, the Trial Mirror was installed under the handlebar. The mounting hole for the OEMB Back Mirror was left open. Well, it is OK to ignore it, but it is not so nice, so I covered the hole.
Functionally, a cheap and lightweight Plastic hole plug is sufficient. However, the Type, which is stuffed into a screw hole, is difficult to put on and take off. (It is easy to put it on by just pushing it in, but a little troublesome to take it off.) For on-road touring, the OEM Mirror is easier to use, so we will return to the OEM type. In such cases, the screw type is more convenient.
The disadvantage is that it is an aluminum cut-out, so it is naturally costly and expensive. You will pay about 1pc.500 yen just to plug the hole. (Plastic hole plugs are lightweight and much cheaper.)
I would recommend it to those who are concerned about the screw holes that removed OEMMirror and who are concerned about looking good or who repeatedly install and remove the OEMMirror.
Inexpensive, lightweight Material if you just want to plug the holes:Plastic is good.
View detail
Mirror Cap
I bought it for some reason, but the texture was there and the price was Reasonable. View detail
Soft.
If bar end mirror is used
It is better to install the Handlebar around the
Normal Thread Screw, Opposite Thread Screw
Note that there are
The material is soft, so if you tighten it too tightly
There is a high probability that Mt. Screw will crumple when it is removed.
Torque is quite light and sufficient.
View detail
nice little accessory
My YAMAHA XMAX300 has refitted the front rearview mirror. The original screw hole needs a cap. I searched for a long time and finally let me see it. There is no difficulty in the installation process. Just unscrew the original mirror screw. Direct installation, I prefer the black appearance, low-key and chic, it matches the car very well, and its material will not rust, which makes me very satisfied ------------ -------------------------------------------- My Yamaha XMAX300 modified the front -view mirror. The original screw hole needs to install a hat. I found it for a long time and finally let me see it. There is no difficulty during the installation process. Installed directly, I prefer the black appearance, low -key and uniquely matched the car, and its material will not rust, which makes me very satisfied Powered by Google Translator View detail
I think black looks better
I have been looking for it for a long time and finally let me see it. There is no difficulty in the installation process. Just unscrew the original mirror screws and install it directly. I prefer the black appearance. It is low-key and chic and matches the car very well. Moreover, its material It will not rust, which makes me very satisfied, and I may never find a better product than it. -------------------------------------------------- -------- After looking for it for a long time, I finally saw it. There was no difficulty during the installation process. As long as the original mirror screw was unscrewed, I could install it directly. black appearance. It won't rust, which makes me very satisfied. I may no longer find a product that is better than it. Powered by Google Translator View detail
High! But cool!
It's just as the Title says, the Anodized colors are really beautiful and upscale!
But it's expensive lol Slotted screwdriver was used to install it. It's so cool, it's a Recommendation!
View detail
usually
The texture is normal and a bit expensive for a Mirror filler. View detail
I bought it again, but it was still too expensive...
I bought a new Mirror hall stash when I reinstalled the bar end mirror, but it was still too expensive.
I like the texture, though.
View detail
No discrepancy, no cheapness, good!
OEMMirror→I bought this to fill the hole because I changed to a bar end mirror. It is totally textured and looks beautiful. I think the price is a little less than Friendly. View detail
In Mirror hall not used by Demon150GR
The GPX Demon150GR has a rubber cap blocking the mirror hall of the M10 Standard Thread Screw, perhaps a remnant from another vehicle, and I'd like to remove it because I'm concerned about the deterioration of the rubber, but in any case I'd like to remove it so that I can use it as a press-up as well. This Mirror Hole Cover Cap is installed. Compared to the common types, the NASA TypeSeries of POSH products have a more rugged design, which I prefer, so I chose this one. I think it is better to install the cap without putting a wound as much as possible. View detail
A little small, but works fine.
Amazon. Normal Thread Screw, Opposite Thread Screw Of Quantity:I bought a set, but both were Normal Thread Screws, so I returned them and repurchased from webike.
I'm not sure if it's cosmetically sound since it's not a Large price.
If you use a bar end mirror, it is necessary to have a pure normal thread screw hole.
The aluminum seemed to deform when torque was applied, so I lightly tightened it with a ten-yen coin.
This product is sufficient because it only plugs the screw holes.
If I had to pick one, I'd say it was Exactly right if the diameter was a bit larger.
View detail
high
I bought it because I made a bar end mirror.
The handlebar is black, so choose black.
I think it's a very expensive product for the price.
Easy to lick when installing and removing with a slotted screwdriver
Don't put too much pressure on it, it will lick you in one shot.
SmallParts, but it's Exactly after Mirror.
Next time I won't buy it.
View detail