Reviews
When replacing the bar end mirror, please be sure to
Among the so-called reverse Screw type, I think this product has a good balance of texture and cost.
I have been using Spacer on the OEM Bolt since I replaced it with the bar end mirror, but I ordered it while I was ordering some things.
I am satisfied with the total because it looks neat and the color gives it Accent.
However, since the material is soft like aluminum, it is necessary to select the size of the driver carefully and dustcloth is essential.
View detail
Due to the change in Mirror location
The Mirror hall was left open to allow water to accumulate, so it was plugged up.
Material is weak, so care should be taken when tightening it.
View detail
Detachable Cover Cap
I bought this to plug the mounting screw holes for the Back Mirror on my KLX125.
I often go to forest roads with KLX, not only open forest roads, but also many attack type forest roads, and sometimes I hit trees with Normal Back Mirror. Therefore, the Trial Mirror was installed under the handlebar. The mounting hole for the OEMB Back Mirror was left open. Well, it is OK to ignore it, but it is not so nice, so I covered the hole.
Functionally, a cheap and lightweight Plastic hole plug is sufficient. However, the Type, which is stuffed into a screw hole, is difficult to put on and take off. (It is easy to put it on by just pushing it in, but a little troublesome to take it off.) For on-road touring, the OEM Mirror is easier to use, so we will return to the OEM type. In such cases, the screw type is more convenient.
The disadvantage is that it is an aluminum cut-out, so it is naturally costly and expensive. You will pay about 1pc.500 yen just to plug the hole. (Plastic hole plugs are lightweight and much cheaper.)
I would recommend it to those who are concerned about the screw holes that removed OEMMirror and who are concerned about looking good or who repeatedly install and remove the OEMMirror.
Inexpensive, lightweight Material if you just want to plug the holes:Plastic is good.
View detail
Mirror Cap
I bought it for some reason, but the texture was there and the price was Reasonable. View detail
Soft.
If bar end mirror is used
It is better to install the Handlebar around the
Normal Thread Screw, Opposite Thread Screw
Note that there are
The material is soft, so if you tighten it too tightly
There is a high probability that Mt. Screw will crumple when it is removed.
Torque is quite light and sufficient.
View detail
High! But cool!
It's just as the Title says, the Anodized colors are really beautiful and upscale!
But it's expensive lol Slotted screwdriver was used to install it. It's so cool, it's a Recommendation!
View detail
I bought it again, but it was still too expensive...
I bought a new Mirror hall stash when I reinstalled the bar end mirror, but it was still too expensive.
I like the texture, though.
View detail
I can't find a substitute.
Originally it would be something to fill in when you remove the Mirror, but I had a part of my kid's bike that I wanted to block off from the M10, so I bought it with the extra Point.
Because it cannot be said that it is indeed hand tightening, I thought to use Slotted screwdriver, but as far as the Screw head is concerned, Slotted screwdriver was expected to bite, so I took out 500 Yen coin from Wallet and fastened it with a comb.
It's almost a toy Material, but on the other hand, it's not sold in Screw stores, so I'm not sure if it's worth the price.
View detail
Required when running a circuit
When removing the Mirror in Circuit, I use it in place of the Bolt of OEM. In addition, because there is also the plan of Bar end mirror conversion, at that time I thought that a little fashionable one with Color, and chose this one. View detail
It looks good, but the mounting method is disappointing
Because the Exhaust System was replaced and there was one extra bolt hole, I bought it to close it up I did
I use the L-shaped wrench to install it as described in the product information The Wrench can be used to remove the anodized parts around the tightening holes
It's hard to tell if you look at it from the front, but if you look into it, you'll see that it's been scraped off
I hope the Manufacturer will improve it
View detail
GOOD if it is a little cheaper
I used a suitable Screw so far, but it gets rusted and gets pulled out
I used this hole CoverCap.
It was a price I hesitated a little, so I could not buy it. I hope it will be a little cheaper..
Good-looking is also good, rusted and it will not come out, so it's a good shopping
I think that it was.
View detail
To Blind at the time of Mirror relocation
Expansion of Mirror Holder of the company in order to reduce the trouble of detaching Mirror when running Circuit.
I bought this Blind screw to fix Tank Bracket which became Free at that time.
GALE SPEED Master cylinder (Mirror Clamp) 'S Screw hole is M10 Opposite Thread Screw, so you can not make it Blind in a general Cap bolt, and you came to this Blind as a looking script.
- Material : I am glad that there are several color developments in Aluminum.
Choosing Silver is also a matter of making it too colorful.
It is directing a calm color..
- However, it seems that there is not much strength, and when it is concluded with -Driver, I licked a little bit.
Where the fastening strength is concerned.
- Regrettable that prices are expensive and fragile.
View detail
It's nice but it's a little expensive
I bought it to Bolt for fixing Bracket of Brake fluidTank. M10xP1. It is saved because there is not much special Bolt of 25.
It is well made in color and well in shape, but Bolt 1 pc is ☆ 3 because this price feels a bit expensive at Bolt 1 pc.
View detail
It is a bit expensive
【What made you decide the purchase?】 It was just a good Large Kisano Screw to close Mirror's Screw hole.
【How was it actually used?】 Anodized It looks good with Aluminum processed.
【Was it difficult to install? (Hard parts case)】 Just a one-yen coin.
【Please tell me the point of installation and hang (in the case of Hard parts)】 I attached a Screw lock agent so as not to loosen by vibration.
[Is there anything I was disappointed about?] nothing special.
【Hope for Manufacturer - Please tell me if you have any improvement points] Screw 1pc. It is slightly higher than 500 yen.
【Have you compared items?】 I looked for 10 mm Screw at Home center, but since I only had a huge Bolt, I did it here.
[Others] There are various colors, you can choose as you like.
View detail
There is a place to which a Mirror is attached for whether ninja250r on which I have ridden has diverted the Handle from another vehicle type. Although the lid of the cheap Rubber has covered the hole there and those who do not care would not do, si
There is a place to which a Mirror is attached for whether ninja250r on which I have ridden has diverted the Handle from another vehicle type.
Although the lid of the cheap Rubber has covered the hole there and those who do not care would not do, since I had been worried, I purchased this product.
It is not because the thing with low
evaluation is not good, but is because the price is only high.
May not you buy it, if change is left since the circumference of a Handle becomes gay only by attaching?
View detail
It is the Aluminum Bolt by which the Anodized was carried out. how [ in 1 piece / Stainless bolts / a price ] in addition eight Stainless bolts can be bought and meet although it is what so much (smile) -- I also regard ? as coloring of an Anodiz
It is the Aluminum Bolt by which the Anodized was carried out.
how [ in
1 piece / Stainless bolts / a price ] in addition eight Stainless bolts can be bought and meet although it is what so much (smile) -- I also regard ?
as coloring of an Anodized becoming an Accent which may be good.
Although form like
honesty and a common Screw was imagined, it is rather than thickness also considered.
the
Anodized -- can the favorite one be recommended?
View detail