Reviews
Satisfied
I am satisfied with Large because it suits my motorcycle EXACTLY. View detail
Fits: KAWASAKI Z900RSCAFE, KAWASAKI Z900RS, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS
the best dress-up item
It's the best dress-up with a long tail. It's a real old z-series look. You can say I did a long tail because of this. No problems with visibility, brightness, etc. View detail
You should buy it when you find it.
It would be nice if they had them in stock when I wanted them, but they are often out of stock. When I find one, I buy it immediately. View detail
It will look different when the Light area is cleaned up!
It's beautiful, it's good! The look, the Impact, the difference! View detail
Fits: HONDA CB400 Fore (air-cooled), HONDA CB400 Fore (air-cooled)
Meter Replacement
The installation was completed and the atmosphere of the vehicle changed at once, and I am satisfied. View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR)
Reliable Nikko Horn
The Horn is almost the same as the OEM Product except for the absence of the plating section.
The volume is quite Large, which must have been an improvement since then.
View detail
Satisfied
Satisfied if not particular about OEM Product! View detail
PMC LED taillight
About quality and texture Great product. Quality as good as the OEM itself About the feeling of use Looks great with the clear case and the O ring light. Products to buy together No other parts needed as I installed on my OEM rear fender. Difficulty of installation Needs about 20 mins to reach the screws just unplugged n plug. Easy to install. Cost performance and comparison with other products Good cost doesn't break the bank. About shipping and packaging Well packed in a box. Any concerns, cautions, or advice when purchasing The braking light may look a bit small. But I think it's sufficient on the road. View detail
Fits: KAWASAKI Z750FX, KAWASAKI Z1000 MkII
Tail lamp lens
It was very nice and very close to the real thing for a reprinted product. View detail
Fits: KAWASAKI Z1000 (air-cooled), KAWASAKI Z750 (air-cooled), KAWASAKI Z900 (KZ900)
For installation of CR Carburetor
I bought this product because it has a better cost performance than the OEM Product. I chose this product because it has better cost performance than the OEM Product, and it looks good because it is black while the OEM Product is a little greenish. View detail
Fits: KAWASAKI Z900RSCAFE, KAWASAKI Z900RS, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS
"cool
Satisfied with the old car look.
Installed on PMCL Long tail SlightRear Fender with no problems.
Especially if you use SlightRear Fender, you have to transfer and install the NORMAL License Plate Light, but this Tail lamp is integrated with the License Plate Light, so you can remove the NORMALLicense Plate Light. However, since this Tail lamp is integrated with the License Plate Light, the NORMALLicense Plate Light can be removed and refreshed to give a good impression.
The Instruction Manual was available, but it was easier to understand the installation procedure by watching the Manufacturer's YouTube video.
It is easy if you follow the steps.
View detail
Fits: KAWASAKI Z900 (KZ900), KAWASAKI Z750 (air-cooled), KAWASAKI Z1000 (air-cooled)
There were no concerns about quality.
I think the quality is almost the same etc. as OEM. View detail
Fits: KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4)
Purchased for Kawasaki 650RS (W3)
The two die-casting parts other than the main switch will not be used for the W3, so they are useless, but it is important to have new parts for a 50 year old vehicle. Since the main switch is being replaced, the key will of course be changed and the old key will no longer be usable. View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4)
Used for Z750four
I purchased this product because the OEM Product that came with it originally broke.
Originally for Z2 (RS) The color of the Wiring Cord is different from that of the Z750four, but the Bullet Terminal is male and female, so there is no problem if the OEM Product is replaced with the male and female Harnesses on the body side as is.
The OEM Product Spring was too long to reuse as is, so we cut the hook part of the Hook a little to reduce the overall length and reuse it.
I am satisfied with the new, clean and Large!
View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750 (air-cooled), KAWASAKI Z900 (KZ900), KAWASAKI Z1000, KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z750 (air-cooled), KAWASAKI Z900 (KZ900), KAWASAKI Z1000
The needle has stopped swinging.
The DamperOil in the OEMTachometer had come loose and the needle was oscillating in the range of 1,000 rpm. As a result, the runout stopped and the needle started to move normally. I am not sure if the Cable was really bad or not, but as a result, I was glad to have replaced it. View detail
Fits: KAWASAKI Z750 (air-cooled), KAWASAKI Z900 (KZ900), KAWASAKI Z750 (air-cooled), KAWASAKI Z750 (air-cooled)
Motorcycle Accessories
Thank you for your prompt response.
We live in an age when things that used to be taken for granted are hard to come by.
Please keep up the good work with Reasonable products.
View detail
pretty good
I thought it was fine to have a NORMAL Tail lamp, but I can't see it from me …. But when I was running behind my Z900RS friends, I couldn't help seeing this Abalone Tail! So I replaced it by removing the Tail cowl and the Bracket + ScrewQuantity.:Just remove the 2pcs, remove the power coupler, replace the body, and put it back together! Parts to show everyone how cool your butt is! View detail
Fits: KAWASAKI Z1000 (air-cooled), KAWASAKI Z750 (air-cooled), KAWASAKI Z900 (KZ900)
Necessary and sufficient.
It is a Rubber part and is replaced regularly.
The Z series has a large vibration, so the role of bushings is large.
View detail
Fits: KAWASAKI Z1000 (air-cooled), KAWASAKI Z1000 (air-cooled), KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000
I was able to install it easily.
Purchased due to defective Handlebar Lock and Seat lock.
Installation took about 15 minutes.
View detail
Fits: HONDA CB1100F, HONDA CB750F, HONDA CB900F, HONDA CB1100F, HONDA CB750F, HONDA CB900F
Coil sub-harness
I bought this harness to go along with another harness that is for the coils. This harness is well made and looks and works as well as OEM. Buying electrical items is always difficult butbin this case there were no problems with the ordering, shipping abd insralling on the bike. All mistake free. View detail