Reviews
Good cooling effect Up
OEM1. 1kgf / ? COOLTECH-R1. 3kgf / It is slight, but you can expect a cooling effect.
You can also use the product with confidence as you build the product well.
View detail
As this is called Original?
Black Looking for a way to make it fancy without painting a car that was one color, we decided to buy it here.
Examining and selecting Unicorn.
Thanks to Hide and kitchen two transformations, I became able to call out occasionally.
Use the Net to inspect it, paste hard with soapy water and Dry ya.
Even if it deviates somewhat well Warge OK!
After pasting for more than half a year, the edge end was peeled a little bit, but again, using Spray garbage every time things are not completely removed.
However, because the Instruction Manual drawing at the pasting position was not easy to understand, it is unknown whether it was truly attached to the same place as the intention of the producer.
If possible we wanted the drawing to be prepared to be similar to the appearance of Motorcycle.
View detail
ZrX1200R (2001) Reverse car
I exchanged the ZrX1200R Radiator cap before it leaked out. Type S is same as NORMAL. Since it is a product, I chose Type R which can withstand higher pressure than NORMAL Even if the cooling efficiency is delayed and the pressure inside the Radiator is rising it is more safe than NORMAL.
BoltQuantity which fixes Tank by removing Fuel Hose and negative pressure Hose for work : Remove 2 pc and pull out the fuel gauge Coupler and Drain hose while lifting the tank slightly, remove the tank, exchange the Radiator cap and it is the end.
It is not expensive, so it is better to exchange them together when changing Coolant Type R It is recommended..
View detail
ZX - 14 Coolant exchange
Coolant replaced in accordance with replacement. OEM pressure 1. 1 to 1. 3 and modest, I tried to increase the pressure up to increase the cooling effect. Leak from Hose etc etc etc etc etc. It is a nice feeling because it is good, because it is also good in terms of design, I think that it is better than exchanging OEM as it is. View detail
Replace from OEM
`Coolant exchange of 01ZrX1200R, simultaneous exchange
If I do not notice it has not been changed for about 7 or 8 years - -
As Packing's Downs was seen before exchange, I wonder if I could exchange it.
Engine is NORMAL and cooling is also NORMAL, so if the same pressure as OEM is enough.
If the same performance as OEM, this one is a bit cheaper.
In the case of ZrX, Cap is below the Tank so it will not be visible.
View detail
RrBlinker expansion
After changing from OEM to ACTIVE's License Plate Holder with LED Blinker, there are indications that acquaintances are difficult to understand and purchase as an addition to RrBlinker.
I do not care much about power saving (Or say, Battery's lifetime if Battery is hit by Blinker) So, usually buy things of Valve.
Both sides are affixed to the fixed position of the OEM, and W / H passed through the OEM mounting hole.
It took me a while to get through Wiring, but the neighborhood was up to Motorcycle.
Satisfied that it was said that it became easier to understand from acquaintances.
However, if it is an OEMB linker relay, it seems to be slightly high flasher.
Once 120 / There is no problem because it is flashing within minutes, but Blinker relay will be replaced with ICRelay.
I think there is sufficient performance as RrBlinker.
View detail
To cooling up !!
Outside of the summer, a hot word from V4Engine is a tremendous word.
In addition, the water temperature gauge is Milumy Rise in traffic jam. I tried to buy it for countermeasures. Parts to boost the boiling point and increase the cooling rate by pressure increase. Just exchange for OEMRadiator cap. OEM has StopperScrew
Screw will not be attached when exchanged for this. I do not know clearly the effect of the key.
View detail
It is good..
Although Type S was attached up to now, since performance is exactly the same as OEM, I replaced it with Type R, but I think that the time it takes for fans to be shortened from Type S, so I think that there is an effect. Just because the pressure is higher than Type S, there is a danger of water leak if you do not tighten the band of the Radiator hose again.
View detail
Easily attached
I installed it in VF 750F.
Easily attached.
I was worried about whether to make R and S before purchase.
But I chose R.
The reason is ... I think people understand V4.
Data OEM 0. 9 ± 0. 15kg / Centimeter 2 ... 1. 3 Large Sturdy?
But if you can improve even a little ... what.
Everyone thinks the same, if water pressure rises it is weak that water leakage will occur ... ... please leave me, I will do something.
Besides, it is hot. - It's hot, in the summer the fans turn around waiting for a signal and it will not stop.
However, replacing this Cap will improve it slightly.
It is a little, but I'm happy..
At the beginning of this installation, Sticker on Cap is also Beauty but it is already fading.
Cap as much as I can.
I think Motorcycle feels the same.
View detail
Because accuracy is low, unexpectedly - - -.
It usually takes less than 5 minutes to install, but because Spacer is somewhat less accurate, Spacer is hard to hold, it took about 15 minutes to install.
Lever grip width increased and it became easier to operate, so excluding the above, it is a good product.
View detail
Measures against Overheat
The season gradually approached summer and it became the season when water temperature became matter of concern. Indeed, Coolant (water) It wiped, the Radiator lacked water, the cooling effect became worse, the temperature became hot and the temperature became difficult. At that time I was worried that the Engine would not break, and the water temperature of Meter has also reached 120 ° C. Immediately after that, some kind of countermeasure was required, and we reached this product.
Since boiling point rises, it is less likely to wipe the water, so it is difficult for Air to bite into the Radiator, and the cooling effect has stabilized.
It is recommended for vehicles that wipe the summer radiator.
View detail
The degree of effect - -
OEM's Cap seems to overheat soon so I bought this product.
Because pressure is higher than OEM, it is easy to warm and it is easy to cool, it is such feeling. It is truly a sensory thing (Lol)
I am looking forward to seeing it in summer.
View detail
Since change of the boiling point is not independently considered, it uses for a free Replace.Since a authentic positive one was in the state which are not exchanged once, 1.1k of the pressure is chosen.Aren't they five stars when it is about 1000 yen
Since change of the boiling point is not independently considered, it uses for a free Replace.Since a
authentic positive one was in the state which are not exchanged once, 1.1k of the pressure is chosen.Aren't they five stars when it is about 1000 yen?
View detail
Former Cool technical center Since the CARBURETOR was exchanged for a Racing type although Type S was used, the pure lay water temperature rise was large, and since it was high-temperature, it exchanged for Type R this summer.although water temperature
Former Cool technical center Since the CARBURETOR was exchanged for a Racing type although Type S was used, the pure lay water temperature rise was large, and since it was high-temperature, it exchanged for Type R this summer.although water temperature does not go up to operating temperature -- a feeling ordinary year -- water temperature -- it is also important to manage as that was high and components needing periodic replacement! Although it is Type S, it is a Neck about a price. View detail
Since it Was worrisome that the Lever of RCS hits the Switch box of XJR1300, it purchased.Without surely contacting SW VOX, to the last, it grasped and put after exchange. If the direction to worry is considered since a price is also
Since it
Was worrisome that the Lever of RCS hits the Switch box of XJR1300, it purchased.Without surely contacting SW VOX, to the
last, it grasped and put after
exchange.
If the direction to worry is considered since a price is also cheap, even if it has hit, cannot finish
Disengaging a Clutch, but how is it?The
point of difference is a point that black authentic positive in a brembo differs from the black of a PLOT Lever a little.The color of
PLOT Lever was the black of touch like an oily pen.A color authentic positive in the
brembo is deeper black.The slot is not engraving the back side of the PLOT Lever with after
.The slot is carved a
brembo authentic positive one.
View detail
It purchased, in order to attach a Brembo caliper to VTR-F. Although the Support of the Active was also good, since it seemed that there was only a PLOT, the object for one side was decided to be this. It is beautifully satisfied with the simple Des
It purchased, in order to attach a Brembo caliper to VTR-F.
Although the Support of the
Active was also good, since it seemed that there was only a PLOT, the object for one side was decided to be this.
It is beautifully satisfied with the simple Design of structure.
View detail
It is a Radiator cap of 1.3-kg pressure. Although it is an object for Motorcycles, it can use also for a car and can also use the Cap for cars. Although the goods of 1.2-kg pressure called Type S are also put on the market from the co
It is a Radiator cap of 1.3-kg pressure.
Although it is an object for
Motorcycles, it can use also for a car and can also use the Cap for cars.
Although the goods of 1.2-kg pressure called
Type S are also put on the market from the company, I think that it is not needed if there is Type R.
If it equips, it will boil at 126.8 ℃.
It is one article which further improves the engine performance of
cooling water.
An Overheat can be prevented by concurrent use with a heat block Plus of the
WAKOS.
View detail
It attached to the Front-blinker part of NINJA250R. The size can be right just and it can plug up the hole to which the Blinker of the original manufacturer's product is attached. It is as having expected appearance and the engine performa
It attached to the Front-blinker part of NINJA250R.
The
size can be right just and it can plug up the hole to which the Blinker of the original manufacturer's product is attached.
It is as having expected
appearance and the engine performance, and is satisfied.
View detail
Since it damaged when the light was switched on in a Circuit etc., the protruding pure Type purchased this attachment type product this time. When not much small, not only not achieving an original duty but poor maintenance may be taken, but I think that
Since it damaged when the light was switched on in a Circuit etc., the protruding pure Type purchased this attachment type product this time. When not much small, not only not achieving an original duty but poor maintenance may be taken, but I think that this product is goods which can save moderate size and visibility. View detail
Since the Rubber portion of an established Cap deteriorates and it was easy to go up water temperature a little, it exchanged for this Cap with exchange of a Coolant. Although it was not the original manufacturer's product, it was able to use satisfa
Since the Rubber portion of an established Cap deteriorates and it was easy to go up water temperature a little, it exchanged for this Cap with exchange of a Coolant.
Although it was not the
original manufacturer's product, it was able to use satisfactorily.
the thing before exchange was also old -- it is -- there is admiration by which 圧 was stabilized as for after exchange and the water temperature rise was also suppressed.
I think that sense of security is obtained even though there is no dramatic effect.
View detail