Reviews
PinGelCook!
fcr33πI changed to PinGel to install the carburetor because of the Gasoline flow rate, even though the OEMCook does not interfere with it. The main purpose of this project is for appearance, but… I think it's a good idea.
As other reviewers have mentioned, the hole on the tank side has to be cut down a little to make it larger.
I have wrapped a couple of rolls of seal tape around it and I am happy with it, no gasoline leaks and better parenthesis. If it were a little cheaper, I would have no complaints.
View detail
Mk2 with tmr36 and PinGel6000
I installed a tmr36 on a mk2, and the OEM cook completely interfered with the installation, but with a 6mmOffset PinGel6000 mounted slightly to the rear, I was able to complete the installation without any problems. View detail
Dress-up
There are many effects, but OEMCook...
For dress-up because of yabo
Installed. It looks very
Well-organized and satisfactory, but perish Brown bitter Brown
WhiteRust is easy to find.
View detail
External carburetor accompaniment. Indispensable.
In my opinion, it is a necessity for vehicles with external big cabs, but not for normal cabs.
We are using it in Lectron, but Bore up & Big cab Quantities:I feel the need for the first time in Set.
It is not recommended to attach it to a vehicle that looks NORMAL, as it will only cause loss of Reserve and inconvenience.
Well, I don't have to tell you this to those who can maintain MACH…
View detail
Fits: KAWASAKI 750SS MACHIV H2 , KAWASAKI 750SS MACHIV H2 [Mach].
Required when PinGel is installed
Required when attaching PinGelCook
We used it for MACH.
Use less-used water tapes for installation
Buy at Home center.
View detail
PinGelSingle outHigh flowFuel CockriReserve with 3/8NPT
When I changed the Carburetor, I replaced the negative pressure type Fuel Cock with a direct type PinGel.
Because the screw part is aluminum, if it tightens too much, the screw mountain is destroyed and it becomes useless.
View detail
PinGelAdapter plate for 3/8NPTCook
I bought this when I changed my Carburetor to TMR-MJN and when I changed my Fuel Cock from negative pressure type to direct pressure type. View detail
Fits: KAWASAKI ZX10R (lowers motorcycle 2)
Lowdown on SS
I bought it because I want to get the whole Forme down the rear a little bit. You can easily replace it by making use of the PANTAHGraph on the car and setting the Rear to Free. The image is lowered by 25mm when the car is not in the car, and it will be lowered further when a person gets on it. I didn't feel any change as far as Touring is concerned because I don't run GunGun in the mountain passes. View detail
Fits: KAWASAKI ZX10R (lowers motorcycle 2)
plain
It's not a problem for me. It's not a problem for the accuracy of the product, but the price of the product is unacceptable. View detail
It's just the right thickness.
This is a must when PinGel Cook is installed. It is made of a moderately thick Gasket, so as long as the bottom of the Tank is not rough or distorted by Rust, there should be no leakage of Gasoline.
If it is still blotting after using this, then either there is a leak from the Screw section or the parallel is not showing on the bottom of the Tank.
View detail
I love the inconspicuous Black color
I've had a Chrome PinGel on my Motorcycle since I bought it used
Since it's an older car, the OEM Product may have been discontinued and put on as a replacement
About two months ago, I had to replace the tank due to some problems with the fuel sensoretc I went with PinGel in Black, which is less noticeable than Chrome
So far I have no complaints about the features, but as others have implied, On, Off, and I would like to see a sense of click to make the Reserve position easier to understand
Large without any knowledge of it Cook is this But I forgot to turn it off once in the past and made it overflow If there is a compatible product that can be diverted, ManufacturerOEM's negative pressure cooks are ideal
View detail
Being driven by the need
Since Normal cook interfered with TMR, exchange
In addition, I tried Offset before but maybe it was not necessary.
In order to attach PinGel's Cook to GPZ, you need something Plate so purchase with Set
Making it is tolerable ... ... It is absolutely necessary things so it's a little cheap and I appreciate it. Is not it okay to set it?.
View detail
Being driven by the need
Since Normal cook interferes with carburetor, exchange
Satisfied with shape and quality
If you dare to raise a bad point ... Because the position of the Reserve is in the middle, the alignment is rough and makes it difficult to use.
Would it be better if there was a thing like Notch at each position.
movies "Harley-Davidson & Marlboro man" It was this that I was quitting on the OP.
I was moved in a strange place.
View detail
I installed it in GSX 1100S
PINGELPinGel : Single Out High Flow Fuel Cock 1 / 4NPT with Reserve(http : / / www. webike. net / sd / 21354242 / I bought it to install.
First I bought a product without Offset but because Cook interferes with Carburetor heat guard, the item I bought again will be here.
Offset was created on the Tail side and there was no interference and Fuel Cock was able to be used properly from RES to ON.
View detail
Fits: KAWASAKI GPZ750R NINJA, KAWASAKI GPZ900R NINJA, KAWASAKI Z1000 (air-cooled | KZ), KAWASAKI Z1000 (air-cooled | KZ), KAWASAKI Z750 FX I, SUZUKI GSX1100S KATANA, SUZUKI GT380, SUZUKI GT380, SUZUKI gsx1100s katana [katana]., KAWASAKI Z750 FX I, KAWASAKI Z1000 (Air-cooled|KZ), KAWASAKI Z1000 (Air-cooled|KZ), KAWASAKI GPZ900R NINJA [Ninja]., KAWASAKI GPZ750R NINJA [Ninja].
I installed it in GSX 1100S
PINGELPinGel : Single Out High Flow Fuel Cock 1 / 4NPT with Reserve
http : / / www. webike. net / sd / 21354242 /
I purchased it at the same time and attached it to the GSX 1100S.
Carburetor on CR33 This Plate and PinGel combination can be installed without problem.
Compared to NORMAL, switching between ON and OFF Cooks has become easier but the impression is that the performance does not change at all.
In principle, the flow rate of Gasoline may become faster, but ,,,,
View detail
I installed it in GSX 1100S
Fuel Cock is getting fuzzy & I want to cool coolly Buy PinGel with 2 points. It is not enough to attach to GSX 1100S, and at the same time 【PINGELPinGel : Special Off Set Plate for 1 / 4NPT Fuel Cock】 http : / / www. webike. net / sd / 21354199 /
Also necessary. The reason for having made it Offset is because when it was wearing CRcarburetor, it became the best angle such as the position of Cook.
First of all, I think that we can attach even if we do not have that knowledge for 30 minutes, just by removing Tank, removing Gankoline, taking out existing Cook and attaching it according to Instruction Manual.
As impressions to be attached, since Gasoline is often sent to the carburetor well, it is said that it is necessary to have the air conditioner but there is no difference in performance and so on at all for himself.
It is perfectly visible Parts
View detail
It is recommended at FCR of a 4 cylinder. Branch becomes a smooth from Y character or T character. Since a filter is also exchangeable, also functionally, it is good also in looks!
It is recommended at FCR of a 4 cylinder.
Branch becomes a smooth from Y character or T character.
Since a filter is also exchangeable, also functionally, it is good also in looks!
View detail