Reviews
Fits: YAMAHA MT-09
Pad protrudes from disc.
As you can see from the Up photos, the accuracy is very low. The disc is OEM, Caliper is when using brembo's new Crab. MT-09SP (2022). View detail
Fits: KAWASAKI ZX-4RR, KAWASAKI Ninja ZX-25R, KAWASAKI Ninja ZX-25R SE, KAWASAKI ZX-4R SE
Not possible to share with 250.
However, the Swing Arm and Rear tire interfere with each other because the Tire is one size thicker than the 250 and the Chain is 2 links shorter than the 250. I tried to solve this problem by setting two small Driven Sprockets, but still only 2mm of Clearance was secured.
In addition, the vehicle height has been raised by about 1 cm at the license plate position, and the vehicle body tilt has become much larger when the side stand is set up.
It was disappointing because this is an expensive product and this should have been mentioned in the product description beforehand.
View detail
One more twist and it's excellent!
When I purchased and installed the handlebar grip, I replaced the handlebar grip with a rubber grip from For Motorcycle.
Now for the Review, the person who Tandem'd it said that the hand holding the Handlebar Grip hits the back, so in the summer, the driver's back heats up …w, but it doesn't seem gross if you wear a thick jacket and gloves. w
For those who carry children, it is likely to be safer to have it.
As a driver (MotorcycleUser), I struggle with the sensation of a hard object hitting my lower back while driving. It hurts a little. I would like to put a cushionetc. in between, but I can't because the sitting position is too far forward.
Quantity of Cushion:Pair (for Left and Right) If the Handlebar Grip is located on the backrest, it can be used as both a backrest and a tandem grip, and will be very useful.
I hope Manufacturer will improve it.
That said, the texture of the Stainless Steel part is good.
Also, when using the Center Stand or walking around pushing the Motorcycle, it is a different way of using it, but it can be quite useful.
View detail
short
For Over's Rear Sets Change Pedal, I believe it was originally this length, but personally, I found Short difficult to use myself. View detail
worst case scenario
SliderBracket gets stuck in the Engine because of a standing mock-up
Crack has been added to the cylinder and cylinder head
Wrecker transported due to oil leakage
Repair estimate is $250,000 OverRACING!
View detail
It is only Parenthesis.
Even if you hit it with Prague on hand, you can not go in any way. It was useless to soak in hot water and warm it up. I thickened it in the Device, I got a little strange but it floated a little. Left's change side has become oblique. It happened that I planned to go to Shop to exchange the Tire, so I got it to come in at the same time. After all, PRO has tools and arms quite different.
In addition, it was Yellow as the character of Logo whether it was a long-term inventory item.
View detail
The price is high, the way of installation is bad
Anyway, Slider, installing Bolt does not fit. Forcibly put on, Slider side is scratched. To install on Body, you can not use Wrench straight, so you can not tighten properly. I bought it and failed.. View detail
Fits: KAWASAKI NINJA1000 (Z1000SX), KAWASAKI NINJA1000 (Z1000SX)
I thought that it would be easy to adjust if it waves, such as angle adjustment. Since the Brake hose is changed, a Banjo Bolt will interfere at the time of a Down. texture is very good.
I thought that it would be easy to adjust if it waves, such as angle adjustment.
Since the
Brake hose is changed, a Banjo Bolt will interfere at the time of a Down.
texture is very good.
View detail