Reviews
Outstanding Workmanship Accuracy
I was going to settle for a cheap wide stand from an unfamiliar Manufacturer.
We chose this one because we were notified of its release by Over, a safe and reliable company.
The ground contact surface is firmly level with the ground, and there is only a gap that may or may not contain a sheet of cardboard.
(The photo above shows the gap, but it can be narrowed down a little more after adjustment.)
It was expensive, but I liked the satisfactory workmanship.
I chose the Powder coat one to avoid flying gravel.
The color is close to the paint of the OEMSide Stand, which is nice without looking bad.
However, two points should be kept in mind when installing the system.
1. side stand must be installed with the side stand raised
This product has a slight rattling to absorb errors on the car body side.
As mentioned in the Instruction Manual, fine adjustment of the mounting position is required before tightening the Bolt.
In this case, the Side Stand needs to be adjusted with the Side Stand raised.
Assuming that one person installs the handlebar, he/she will work while squatting and holding the handlebar with one hand.
If you tilt out of balance, you will have two choices:you will be caught between the Motorcycle and the Exhaust System, or you will be knocked over to the Exhaust System side.
We recommend using a Maintenance Stand or working with two or more people, but
When working alone, put it in 1st gear and use Brake Lock as shown below to stabilize it.
DAYTONA:Front Brake Lock
https://www.webike.net/sd/21825075/
2. low specified Torque
I use M5 and M6 Bolt to fix it, but the tightening Torque is specified to be less than 10nm.
This value cannot be set for some types of torque wrench. (Especially if it is for suspension, it may be too severe.)
The Bolt is tensioned so that it is relatively difficult to loosen, but
It is recommended to adhere to the specified Torque + use Threadlocker in combination.
Since the base material is aluminum, experience has shown that it licks easily when tightened by intuition.
Since no other parts need to be removed during the installation process
It is a relatively easy component to install.
It is expensive and Bolt can be loose and dropped.
Be careful not to ruin it.
View detail
Does not fit Hunter Cub J65 vehicle...
I really like the quality and finish of the product...
It doesn't fit my hunter curve.
I searched and purchased it, but this was the first time I realized that there were separate markings of 55 and 65 in the model name.
Perhaps it was for domestic use or for export, but it did not fit the Korean stand.
That's too bad. -------------------------------------------------- -------- I really like the quality and finish of the product ... It doesn't fit my hunter curve I searched and purchased, but I first learned whether there were 55 and 65 notations in the model name. It was not suitable for the Korean stand, whether the domestic export was wrong. That's too bad. Powered by Google Translator
View detail
I like it so much
First of all, the delivery is very fast
Product condition, packaging condition, finish, etc.
I like it so much
And the manual was also well packaged.
I wish you all the best in the future...
...
...
...
...
...
...
...
...
...
...
...
...
...------------------------------------------------------------- ----------- First of all, delivery is quietly fast Products, packaging status, finish, etc. I like it so much And the manual has also been well packed Thank you for your future ... Of Of Of Of Of Of Of Of Of Of Of Of Of Of Of Of Powered by Google Translator
View detail
side stand
About quality and texture The front fork is xr100, so there was no problem using the standard tape100 stand About the feeling of use There was no big difference from the standard Products to buy together Overracing backstep must be together Difficulty of installation Contrary to the standard, the spring had to be installed in reverse Cost performance and comparison with other products It has a design that is close to the standard of other products About shipping and packaging I received the delivery in a week Any concerns, cautions, or advice when purchasing You should also purchase the APE100 standard front pork stand with ape50 stand View detail
For people who won't let the Full Bank
APE 100 as Rear Sets, with APE 100 OEM STAND and Spring Bought it because it can be installed No problem to install, but the OEMSTAND makes the motorcycle stand up too much and I'm worried about it The OEMSTAND touches the road surface before the Full bank There is no reason to use Rear Sets in this case View detail
Since the back step of over was purchased, it purchased here. It did not investigate well, but since it purchased, it failed, but it is carried out very well firmly, and if the price of structure is to a slight degree cheap, it is recommended very muc
Since the back step of over was purchased, it purchased here.
It did not investigate well, but since it purchased, it failed, but it is carried out very well firmly, and if the price of structure is to a slight degree cheap, it is recommended very much.
The failure story is written to the diary.
View detail