Reviews
Fits: KAWASAKI Ninja H2 SX, KAWASAKI Ninja H2 SX SE
Required processing
The mounting holes do not match.
I installed it by pulling and bending each part.
I'll revert to OEM after a while.
View detail
Fits: HONDA CBR600F, HONDA CBR600RR, HONDA CB400SB, HONDA CB400X, HONDA CB400SF, HONDA CB400F, HONDA CBR400R, HONDA CBR900RR, HONDA CBR1000RR, HONDA CB1000SF, HONDA CB1300SF, HONDA CB1300SB, HONDA CB750, HONDA VFR800F, HONDA VFR800X, HONDA VFR1200F, HONDA VFR1200X, HONDA HORNET900, HONDA HORNET600, HONDA CBR1100XX
Is this Carbon Style?
I ordered Carbon Style, but what I received is more like a Check pattern of White and Black than Carbon Style.
I am disappointed.
View detail
Fits: KAWASAKI ZX-14, KAWASAKI ZX-14R, KAWASAKI ZZR1400
It's bright and snappy.
[How is it used?
One week after installation.
Was the one you received as per Image?
Just like the picture of the product.
Was the installation difficult?
I think it's easy if you have experience removing and installing Cowl.
How was your experience with it?
Originally I didn't plan to use LEDs, but I got the Blinker lens. [Color] The introduction of the Smoke makes it darker than expected when lit.
The result is a bright, crisp flashing light with improved visibility.
[Included Parts:were they on?
sufficient
[Was there anything that disappointed you?
Two points for me.
When I replaced the Relay, I turned the Relay body 90-degrees and tied it with a Tie Wrap because I thought it would be too much for the wiring if I installed it the same way as the OEM because the Relay body is larger and the wiring is longer.
The fact that it now responds with a slight delay after pressing the Blinker switch.
I'm just a little concerned about both of them.
View detail
Fits: YAMAHA MT-25, YAMAHA MT-03, YAMAHA MT03, YAMAHA MT03
A little expensive but generally satisfactory
Was the one you received as per Image?
Especially, there is no dissatisfaction point. I feel that Cospa is never the product which is good, but because the flatness of the feeling of Y's GearOEMScreen and the extremely SmallScreen which is the effect none of the North American Yamaha were dissatisfied and it chose, it is satisfaction.
Was the installation difficult?
All you have to do is remove the headlight cover with a hexagon and tighten it together with the supplied bolt and collar. There is no wobble etc. especially.
How was your experience with it?
I think the driving wind has been reduced. It is about. Originally, I didn't expect so much windproof effect on the appearance, so no problem.
[Included Parts:were they on?
ScreenBody, Collar×2, Bolt×2, Rubber×2 for vibration isolation, Instruction Manual.
[Was there anything that disappointed you?
The surface was small scratches or a little rubbed, but since it is an imported product, it is like this.
[Point and hang of installation].
When you remove the OEM Cover, the Bracket of the CoverReverse side will also come off together, but be careful because the Rubber which is bitten on the joint part is easy to fall off.
Also, be careful of the tightening torque as the Bolt is tightened with the collar in between. The Bolt can be tightened without limit, so if you tighten it too much, one of the collar, Screen or Bolt may break. Tighten in moderation.
[Others]
The size of the bolt is shown in the instruction manual. (I believe M5×30)
agent (Odax) I bought Dark smoke on the direct sales of the company, and at first they replied that the delivery time was 1 month, but it was suddenly shipped in about 3 days! (Delighted) . Maybe Manufacturer has them in stock?
View detail
ODAXELMeter
It would be better if there was an ELMeter with various patterns.
The installation itself is not so difficult, but you have to be very careful with the Meter needle, otherwise the needle will break.
View detail
If you don't run at night with Tunnel, you don't need it at all.
Well, it's expensive. It's relatively easy to install for some people if they have the tools.
I'm sure you can, but you'll have to be creative.
I don't have a lot of impressions, so I'll add that I didn't notice the dirt and dust unexpectedly.
Small Garbage may be in the Meter after installation.
It's too much trouble to remove it every time, so it's still there.
The stronger one = me. This can be a prime cause of Large failure.
I can't help but get frustrated.
The installation is generally said to be easy, but you can use Leutor to break the shell and specific parts.
I have to cut it down, etc.
If you are really unsure, it is safer to ask Shop.
I will describe the Case I fear.
Drop the Screw = The Screw itself is inexpensive, but finding it is Large strange.
Same diameter, Pitch, same length Actually, there are not too many cases (in HS etc.)
The location of the Inverter looks easy enough to describe, but the Clearance
Not quite Tight
Double-sided tape for Switch installation will peel off if it is not strong enough.
＝You can't know how strong it is until you buy more than once and see for yourself.
I have five different types of double-sided tape, each with different strengths, and I use them all in my experience.
The reason is that you can't understand any strength until you use it.
If you want to install it by yourself, you can do it by yourself.
I'm sure you can think of something, but I hope you don't take my word for it!
Finally, some Case failures such as licking when using inexpensive tools
I wouldn't be opposed to using this as an opportunity to get some solid tools and do it yourself.
Using a Large Torque does not mean an expensive tool!
Because you are using a small Torque, you need to use a reliable tool!
I digress. The tool is expensive because it's crappy.
It means that a tool in a 100 yen shop is enough for a skilled person.
The following is an approximate list of labor costs for installing this product
If it takes time for removal such as Full Cowl, the labor charge is more than 1h (8000yen + consumption tax)
If it is a Naked type, it would be about that Gold amount if this is the case.
It depends on the mechanic who installs it, and the shop's policy.
In my experience, if you're going to outsource, it's essential to tighten up, and absolutely any good shop will do.
Be sure to check it out after you ride it later!
Other people are just other people. You have to protect your own life.
I assure you that you are incredibly untrustworthy.
It's any motorcycle shop in the world!
View detail
Hand protection and wind protection
It is a hand guard that protects your hands from wind and falls, and it has a wide vertical direction and seems to be effective on rainy days. It is made of plastic plate only and does not have a frame of gold, but it will withstand a little impact.
In the packing, the plastic parts were covered with protective film to prevent scratches.
View detail
![POWER BRONZE Naked Windshield [Long]](https://global.webike-cdn.net/photo/impression/a7/a79248f99c0e2a9957f47aaca9d0dc87L.jpg)
Easier on the highway than NORMAL.
I bought it to make the windshield large because I want to run comfortably.
It became easy at high speed, but I also feel that the wind to the body is not prevented as much as I thought because the width of Screen is narrow. The wind hits the shoulder from the arm normally.
In order to use the Smartphone Holder, I wanted to make the angle stand up a little, so I adjusted it with the Spacer under the Screw.
View detail
Fits: SUZUKI V-Strom250, SUZUKI Bandit1200N, SUZUKI Bandit1200S, SUZUKI Bandit1250F, SUZUKI Bandit1250N, SUZUKI Bandit1250S, SUZUKI GSR250, SUZUKI GSR750, SUZUKI GSX-R1000, SUZUKI SV1000, SUZUKI SV1000S, SUZUKI V-Strom1000, SUZUKI V-Strom650, SUZUKI SV650, SUZUKI GSX250R, SUZUKI GSX-R750, SUZUKI GSX-R600, SUZUKI GSX-S1000, SUZUKI GSX-S1000F, SUZUKI GSR600
The shape is different…….
The thing itself is very well textured and I have no complaints.
However, the shape is different,,, it is supposed to fit a 2020 SV650.
If the shape hasn't changed in FY21, it's non-conforming.
The 5 holes on the outside are fine, but the inside is obviously shaped differently.
I disconnected it and it worked well, but I have to admit I was a bit puzzled at first.
I guess if you know what you're doing, you can buy it.
Now, if only it was durable enough.
View detail
Cut and use
Cut it in half to fill the gap of the original Pad.
The initial adhesion is weak, and if it is not softened by heating well, the edge tends to be lifted and the unevenness of the adhesive surface seems to come out easily.
The above is the reason why I tried to apply water and failed.
It's good that they included the AlcoholPad for Edge beveling, transparency and degreasing.
It is difficult to grasp the Image when the base paper is paper and it is applied temporarily, so I want you to use transparent film.
View detail
Fits: DUCATI STREETFIGHTER V4 S, DUCATI STREETFIGHTER V4
I bought it because I get a lot of wind.
"DUCATIPerformance
I haven't done any highway driving, but the Screen is still quite effective.
However, when Screen is attached, the design is still a little unacceptable. (Kills the original Design) I've become a
Implementation itself was easy, but if you have a Smartphone Holder on your Handlebar, it might interfere with the Screen.
View detail
ODAX EL Meter Panel
My model: Kawasaki z900rs cafe, material: spray panel, with brightness switch double glue, complete accessories, effect: more beautiful than the original factory, more retro style, brightness is also stronger than the original backlight ! Purchase and installation experience: Installation is a bit time-consuming, and the work is slow. The delivery time is very fast, and the goods will arrive at about 7 soon. I am very satisfied! ---------------------------------------------- My model: kawasaki z900rs cafe. Material: painted panel, comes with brightness switch, double sticky adhesive, very complete accessories. Effect: much better looking than the original, more vintage style, and brighter light than the original backlight! Purchase and installation experience: installation is a bit time consuming, fine work and slow work. Shipping time was fast, it arrived very quickly in about 7 days, I'm very satisfied! Powered by Google Translator View detail
Fits: HONDA CBR650F, HONDA CRF250 R, HONDA VFR800X, HONDA CBR400R, HONDA CRF1000F Africa Twin, HONDA CBR650R, HONDA CBR1000RR, HONDA CB650R, HONDA CB650F, HONDA CB400SF, HONDA CB1300SB, HONDA CB125R, HONDA CB1100RS, HONDA CB1000R, HONDA 400X, HONDA CB1300SF, HONDA VFR800F, HONDA GROM-II, HONDA CRF250L, HONDA CB400SB
ODAX fuel tank cover sticker
My car is a CBR650R20 model of Damao Honda, and I bought the ODAX fuel tank cap protector product on Webiike. The material of this product is carbon fiber. The shopping experience this time is very good. Pasting this can protect the fuel tank cap from being scratched by the key or when refueling. I will also recommend Wibaike platform to other friends, hoping that Wibaike products will be more and more, and the price will be more and more favorable. ---------------------------------------------- My motorcycle is a CBR650R20 model of Damao Honda. I bought the ODAX fuel tank cap protector product on Webiike. The material of this product is carbon fiber. The shopping experience this time is very good. Pasting this can protect the fuel tank cap from being scratched by the key or when refueling. I will also recommend the Wibaike platform to other friends, hoping that webike products will be more and more and the prices will be more and more favorable. Powered by Google Translator View detail
Fits: HONDA CBR650R, HONDA CBR400R, HONDA CBR1000RR, HONDA CB650R, HONDA CB650F, HONDA CB400SF, HONDA CB400SB, HONDA CB400F, HONDA CB250R, HONDA CB1300SF, HONDA CB1300SB, HONDA CB125R, HONDA CB1100RS, HONDA CB1000R, HONDA 400X, HONDA CRF1000F Africa Twin, HONDA VFR800X, HONDA VFR800F, HONDA CRF250 R, HONDA GROM-II
PetitCustom
It was a little brighter than Tank's Red, which was unexpected, but it was a good Custom. View detail
I installed it on my Z900RS CAFE.
It is not particularly useful for anything, but I think that the loneliness of the undercarriage was dissolved a little. However, at the time of Oil and Oil Filter exchange, the time and effort of removing and installing increases. It is expected to take about 5 minutes each. View detail
Fits: SUZUKI BANDIT1250F, SUZUKI GSX-S750, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI V-Strom1000, SUZUKI SV650, SUZUKI SV650 X
The blackened version is very beautiful!
My motorcycle originally came with a yellow turn signal cover, which feels too rustic. After I bought this blackened turn signal cover on Webike and installed it, it feels much better, and it fits perfectly! Excellent workmanship! Remind everyone, use screws to unscrew the screw holes of the new cover before installation, it will be much easier to install! ---------------------------------------------- My motorcycle originally came with a yellow turn signal cover. I feel that the original turn signal cover is not good-looking. So I bought this blackened turn signal cover on Webike. This turn signal cover feels much better than originally turn signal cover, and it fits perfectly! The workmanship is great! I would like to remind everyone that before installation, use screws to unscrew the screw holes of the new cover. This will make the installation a lot easier! Powered by Google Translator View detail
Fits: HONDA CBR650F, HONDA CRF250 R, HONDA VFR800X, HONDA CBR400R, HONDA CRF1000F Africa Twin, HONDA CBR650R, HONDA CBR1000RR, HONDA CB650R, HONDA CB650F, HONDA CB400SF, HONDA CB1300SB, HONDA CB125R, HONDA CB1100RS, HONDA CB1000R, HONDA 400X, HONDA CB1300SF, HONDA VFR800F, HONDA GROM-II, HONDA CRF250L, HONDA CB400SB
Anti-slip elbows
When you are running or at a small pause, you can put your elbow on it, but it will not slip. View detail
Fits: HONDA CBR650F, HONDA CRF250 R, HONDA VFR800X, HONDA CBR400R, HONDA CRF1000F Africa Twin, HONDA CBR650R, HONDA CBR1000RR, HONDA CB650R, HONDA CB650F, HONDA CB400SF, HONDA CB1300SB, HONDA CB125R, HONDA CB1100RS, HONDA CB1000R, HONDA 400X, HONDA CB1300SF, HONDA VFR800F, HONDA GROM-II, HONDA CRF250L, HONDA CB400SB
Also fits CBR1000RR-R
Although SC82 was not in the compatible car, it fits without a problem. View detail
ODAX POWER BRONZE Under Cowl
Made of high-strength plastic, impact-resistant and breakage-resistant, the molding process does not require painting, and there is no need to worry about fading. And the price is very cheap, if you like to drive intensely, it is worth buying~Webike China's service attitude is very good。 View detail
NoBrownIt's expensive, but it's going to last a long time, good looking.
We are using this on a 2018 Toracer 900, it's a Custom with Image from Bikespeak. I chose this one because it is expensive but seems to last a long time since we basically run forest roads and FlatDirt on any Motorcycle. It's expensive, but it's cool. View detail