Reviews
Tension bombing at night for sure!
OEMTail lamp of ZX14R is [Color] The front of the bike was more white than clear, and the difference between the front's cool look and the rear's cheesy clear tail was amazing. [ODAX ODAX LED Tail Lamp] We have purchased the
Installation
Tail lamp installation itself is easy even for a beginner!
All you have to do is remove the Screw and replace the Coupler, so it's not too difficult.
……But there is a Screw in a very narrow place, so you have to work hard.
[Quality, texture, visibility
There is not a single defective LED on the Smoked lens, and it shines brightly.
If you see it at night rather than during the day, your Tension is sure to explode!
It's one of those things that happens when you change the lighting system, you change the tail lamp and it's like the whole motorcycle is new!
I was expecting the visibility to be darker than OEM because of the Smoked lens, but that was not the case.
It's rather brighter and more dazzling than OEM.
Conclusion
I think it's better to buy this one from the beginning if you're going to have a painful experience with a cheap no-name manufacturer's product. (Because the hassle of replacing and purchasing is dull)
By the way, I bought a very cheap no-name Manufacturer's Tail lamp once and it hurt me……lol
View detail
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R3
Visibility to the other side is poor.
I didn't like that protruding blinker, so I replaced it.
It looks Refreshing, but it's pretty Smallish.
I might have an accident one day and I'm going to put it back together.
Are you sure you're up for this? Go ahead.
View detail
Fits: YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3
R25 (2019) It needs to be machined for installation to
I have no problems with the performance and texture. It's very good.
ODAX's ICRelay "OX-K60-R. It emits light from inside to outside without any problems when used with
The problem is installation.
The Honda Small Dice Bullet Terminal on the Blinker side (Male) It is not the same as the
BlinkerCable's Bullet Terminal for the 2019 MODEL R25 is a general Bullet Terminal (Female) So,
It is not possible to connect as is. The Bullet Terminal must be replaced separately.
(Guaranteed to fit, though...)
Also, although the Front is a sufficient Cable length
If you want to pull from the Rear OEMFender, you need to extend it by yourself because it's not long enough.
In the case of a Fender Eliminator, for example, it would be Large.
The Blinker Base we bought together WMB-207066. We also had to deal with
That will be noted in the Review there.
View detail
R25 (2019) You will need to be creative when installing it in the
There is no Instruction Manual, but it is stamped with A and B. A is the one with a little large texture.
Although I imagined that the Blinker Base would be used in a pinch.
R25 (2019) I could only use A on the outside for the front cowl of the
I was going to put a B inside, but it does not fit the size of the hole.
It's a universal product, so that's what it is...
Sequential Blinker from the same ODAX "OX-RM001LW-Q-C I'm using it at the same time as
Washer for Flat Parts and Large-textured 8mm stopping OEM Blinker
You can manage to fix it by using it.
It was not possible to install it on the Rear with this product alone.
Base 97420 for DAYTONA's Yamaha/Kawasaki fits in the Rear.
Honestly, I should have used the DAYTONA guy for the Front as well.
View detail
Fits: KAWASAKI , KAWASAKI ZX14 series, KAWASAKI ZZr system, KAWASAKI ZXR series, KAWASAKI Ninja Series, YAMAHA
No problem if used together with OX-RM001LW-Q-C
R25 (2019) in.
The conversion cable is also included and can be installed by simply replacing the OEM Product.
Same ODAX LED Sequential Blinker "OX-RM001LW-Q-C In conjunction with the
It emits light from inside to outside with no problem.
I ran it with a mixture of OEM Blinker and LED during installation and it was fine.
View detail
It's also fashionable.
The Color Film is attached to the attachment, and I was wearing the Yellow Color Film. The conspicuousness was preeminent and always attracted attention with the color of Headlight which is different from others. The installation was installed in ZX10R of 05MODEL (C type) which was riding before, and the Valve shape was H7. But I had a hard time because I couldn't install it without modifying the cover on the back of the headlight. View detail
Good Items for Makeover (^3^) /
Kawasaki = Green Light?
The position lamp is replaced with Green Light
If you don't lose all of the Large variant cowl for the VERSYS position lamp replacement, you will have to I can't access(^^;
Pray for the durability of the Lamp (^o^;)
The rest of the time, don't get warned by the officer (゜゜;) (--;)
View detail
As per Image
Because the Base of the OEM Tail lens is white, the Lens [Color] I bought it because I didn't think it would be as black as I thought it would be even with the smoke processing
When I installed it, it looked just as bad as I thought it would! (Lol)
Good with no LED lights
The gap and the gap between the tail cowl and the step are a little annoying, but depending on the installation of the tail cowl It seems to be resolvable
View detail
Fits: SUZUKI BANDIT1250F, SUZUKI GSX-S750, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI V-Strom1000, SUZUKI SV650, SUZUKI SV650 X
Can it be considered a pimp?
I bought this for my GSX-s1000
There is a problem with the threaded hole in the mounting area as described by others
If you don't have a clearance, the screw will be chewed up too early and cannot be tightened
It may be possible to go there by force, but I have a feeling that the foundation of the screw holes may crack
I'll have to re-drill the bottom hole or, in my case
Slightly close it→Unscrew and blow off the facet→Close it again→ Remove the screws again and blow the facets off
repeated more than a dozen times That's what we did with Quantity:4 Set(~~;
Installation is difficult, but I am satisfied with the color and texture
By the way, the actual product is much more than the photo [Color] Smoke
View detail
Fits: SUZUKI BANDIT1250F, SUZUKI GSX-S750, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI V-Strom1000, SUZUKI SV650, SUZUKI SV650 X
The thing itself isn't bad
I thought it would be easy to use a Phillips Screwdriver 1 pc since it was only for lens replacement, but If you tighten the Screw about halfway, it may become hard, and if you tighten it too hard, it may break When I checked, it was the size hole of the Smaller Screw
I had no choice but to widen the hole by 1mm It took a lot of work
View detail
Fits: SUZUKI GSR750, SUZUKI BANDIT1250S, SUZUKI DL1000 V-STROM650
Unattached and unavailable
The claw shape of the Lens is different from the standard shape
It is likely that the claws will need to be modified in order to be installed
It's a Valve set, which helps, but it gets pretty hot, so you may need to be careful when using it with a hazard lamp will be
View detail
mistake
When installed at the same time as the Day Light Kit, the icRelay, which is included with the Day Light Kit Blinker didn't work, and although it worked with another manufacturer's icRelay Blinker is unstable when I connect Wiring of Back Fog I should have used the daylight kit of the other company View detail
Fits: KAWASAKI ZX-14, KAWASAKI ZX-14R, KAWASAKI ZZR1400
This was usually good
Well, it's a pimped-out version, and the Manufacturer can be trusted (this A different Manufacturer's product was defective at first, but I fixed it myself (e.g. "I'll be back")
To some extent
I give this product a good score
I hope you keep up the good work
However, I would like to see a quicker response to a defective product
Defective = 2 or 3 weeks is honestly atrocious
The manufacturer may argue that the end of the line is the norm, but the end of the line is that no installation defects are the norm I think so, sir
I don't need an excuse
We just need to re-check the operation completely again
It's not a cheap price to pay, so I'd like to make sure that any product works
The low score is based on the Gold amount, which is about as low as you can go to get on a costing scale, so that's why we gave it to you
This time it's Service Points
View detail
Fits: YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3
Parenthesis good!
I couldn't resist the protrusion of Blinker and bought it Parenthesis is better without the protrusion! Installation also Quantity:Pair (for Left and Right) It only takes 30 minutes to do it all together View detail
Date Light added
I chose this product for the Daylight and LED Blinker
There is one more similar product, but it is more expensive because of its multifunctionality …
In this case, it's very inexpensive and very well made and very good in total with Rear!
I think you should be comfortable with the Cowl removal and Wiring process for installation!
If you're not sure, you could hire a motorcycle shop to do it for you
I can switch the Switch on and off in the middle of the car because the law has changed and it's suspicious I'm playing with it
View detail
Fits: SUZUKI GSX1300R Hayabusa, SUZUKI GSX1300R Hayabusa
Blinker's handy LED
'99 Equipment GSX1300R HAYABUSA Blinker installed to make LED.
【Quality / texture】
I think that there is no need to worry about texture because it is an invisible place.
There are no defects with functional problems, Size is similar to OEM and it is normal.
【Performance / Function】
Partly only with LED, all LEDs work fine.
I have not received a car inspection yet, but the flickering interval seems to be problematic.
If there is a drawback, the moment when you switch on starts with Timing of "blinking" of flashing, there is a momentary time lag from when you press Switch to when Blinker glows.
I do not mind so much as there is no hindrance to driving.
Not only this item but the fate of IC Blinker Relay, but even if the Valve expires it will not be High flasher and so we need to check regularly.
【ease of use】
This is undisputed.
Although Universal IC Blinker Relay is inexpensive and commercially available in various ways, in case of installing a common Universal Blinker Relay to 7 pin model, 6 V MONKEY / It is necessary to disconnect GORILLA Main Harness.
There is also an option to let the Blinker side resist resistance without changing the Blinker relay, but in that case, consideration is necessary for assembly as resistance has heat.
This product is unnecessary for such preliminary examination and consideration, it is OK simply by inserting it as an OEM Product.
【Cost performance】
If you consider Universal Blinker Relay you can buy it for hundreds of yen, the honest price is expensive.
It is unlikely that it will be higher than the Universal Product as long as the available models are limited...
What you think of Chinese Copy items is Amaz ○ Because it is about half price in n, let's balance reliability and wallet.
【Review】
The price is expensive, but it is good with machining unnecessary pon.
If there is no resistance to Harness's processing and there is reasonable knowledge, there is a means to make it cheaper, but I think whether it will become a sufficient choice if you want to go with cheap till you get a gold.
View detail
Fits: SUZUKI GSX1300R Hayabusa, SUZUKI GSX1300R Hayabusa
Cospa high!
In blinker LEDization, you do not have to mess with Wiring and do not need any special knowledge.
Simply complete with a popping.
Especially it can be used without errors in use!
View detail
It's neither good nor bad
I exchanged with the Rear blinker ball of NINJA 400 2017.
Valve The LED with a high height interfered with OEMLens, so we chose this item with a low height.
It does not interfere with Lens and its price is also inexpensive compared to other companies, but the light intensity is enough though OEMLens is Clear.
Kawasaki may be part of it, but Valve's Lock pin becomes angle Type.
Please be aware that you can not install if you purchase equilibrium Pin by mistake.
View detail
First, the exchange is completed, White is bright
We have completed exchange installation from OEMPosition lamp to this item. White will light up brightly even during the day. Since Headlight had been converted to LEDs earlier, Balance improved with this. It was slightly uneasy that the replacement work had gotten caught in the shallow stage of the Socket when inserting this LED, when OEMPosition was removed from the Socket, that the workability was poor if Position had almost removed the Full cowl, was. Sometimes I was not used to Valve of T10 Type, I was lost in the power adjustment. Although the main driving was only during the daytime, I felt that even a little bit leads to visibility. View detail
Slightly high
It is easy to install because it only replaces Valve very brightly, but it is better to increase the price slightly, preferably ICRelay at the same time if possible, however, because the PC 40 reverse car has Motor for exhaust Valve and there is almost no space It is difficult to let the 3-wire Type Resell etc. Conversion Adapter for 4 wires etc. View detail