Reviews
The product is Well, and a good impression is made!
The product is designed to be used with the thickness of the Screen and [Color] I think that both the Smoke and the accuracy of the BKT installation are good.
[Color] We chose the darkest Smoke and the most expensive Screen, and we like them in terms of design.
The darker screen provides well forward visibility even when it is cloudy in the daytime, and I feel that the height of the screen is also necessary if you want windproof effect.
Screen strength also seems to be fine at CircuitLevel Speed.
The only reason I couldn't give it more than one star is that there were no instructions on how to install it and I couldn't figure out the proper way to install it.
I used 4 bolt nuts on the Headlight BKT and modified the included BKT a little to install it, but I feel that this method is better in terms of strength.
Overall, I believe we have completely fulfilled the need for increased windproofing while maintaining helicopter TESIStyle.
View detail
honestly speaking, I'm not happy.
There was no other design that I liked, so I purchased it by process of elimination, but it was difficult to install.
I went to the trouble of translating the instruction manual (there was a supplement in the instruction manual that asked for input here, but I couldn't install it in any way, so I installed it in a different way.
I am disappointed that they are selling at this price point with the quality of the processing premise.
I do not recommend purchasing this product if you are looking for easy installation.
The holes in the bracket were too small to begin with, and the rubber was so tight that it was deformed when the well nut was passed through. I decided that it would be impossible, so I installed it without putting the Screen through.
Rubber is quite crushed, so it seems to deteriorate quickly ^^.
View detail
Not as long as a Long.
I ran with it on properly without thinking about the angle, but it still worked.
I think it would be even more effective in a more upright position.
Light smoke seems a bit thin.
But with Dark smoke, it seems too thick.
View detail
[Color] Smoke is good!
The well nut attached to the OEMScreen does not fit in the small hole in the screen, and the hole must be widened to a large size with a file.
Loved the look of it.
[Color] Smoke is matched with Black Body.
Windproofing looks almost as good as NORMAL.
View detail
just right
I thought the Long would be long, but as other posters have said, it is just right. remove the Screw on the Body and replace it with the Bolt that comes with it. You have to put the Spacer between the existing Meter cover and the Bolt, but it is better not to work near the gutter or something, because the Spacer will fall off. Also, the bolt can be tightened as much as you want due to the cushioning of the spacer, so I stopped the bolt with the bolt head sticking out about 1.5mm. I haven't driven at high speed yet, but there is no problem in town driving. View detail
Smoke screen up
Screen [Color] It looks tighter after Smoke. It is just my personal feeling. View detail
Fits: HONDA CB1300 SUPER BOL D'OR, HONDA CB400 SUPER BOL D'OR
Hmm
I had not planned to replace my screens with anything other than an OEMScreen because I thought it would ruin the look of the screen, but since the OEMScreen is not windproof at all and I use a CB as a tourer, I got tired of it and bought this screen. First of all, my requirements for the screen were that it should not look too large and that it should have a shape that would provide windproof performance. I had no idea what it would look like because I didn't see any pictures of it from the front in other reviews. To be honest, I was worried because BOLDOR looks very tacky like a raven hat with an external Screen. I have a picture of it on my phone, but I think it looks cool in person, although the BOLDOR screen looks a little tacky due to its poor photo quality. There was a review that said the color was too light, but I think the OEM screen's color was originally too dark, so I'm not sure why. [Color] I thought Smoke was too dark and tacky, so this color is just right for me. The windproof effect is that the wind that used to hit me up to my chest now hits me above my shoulders, so I can probably ride comfortably even at 100 km or more on the highway. When I installed it, I thought it was not so good, because the screen itself is thin and there is a gap between the cowl and the screen in case of CB400SB. To tell the truth, it is not so nice, but I could not see it unless I look at it very close and it has a good windproof effect, so I decided to put up with it. Also, the seal called "ODAX" on the left side of the screen is tacky and I wish they didn't put it there. (We plan to remove it later.) The middle of the space is raised when viewed from the inside. The middle of the space is raised when viewed from the inside, so it looks like Dustcloth could be placed in that space. View detail
The mounting holes are small.
[How is it used?
Touring。
Was the one you received as per Image?
It looks good
Was the installation difficult?
The mounting holes needed to be machined.
How was your experience with it?
So-so
View detail
Screen Effect
Naturally, it is not as effective as a Full Cowl, but wind pressure in the chest-shoulder area is considerably reduced. View detail
Mounting is unstable and insecure at high speeds
I installed it with the included Parts as soon as it arrived. The installation was completed in Small one hour without anxiety. I drove on the highway to try it out, but it started to shake and hit the phone attached to the Handlebar at over 80km/h. I had to slow down, and when I went into the SA to check, I found that the Material attached to the Screen had been removed.:The rubber grommet was cutting into the stay at an angle and was about to come off. The bolt is held in place by a stainless steel sleeve inside the grommet, so it is not loose, but the stay is a narrow tube, so no matter how much I tightened it, I thought it would not work.
So I took a hint from the OEM Speed screen and made a Stay with 3DPrinter and installed it (the gray part in the image). I think it will need to be adjusted a few times after driving, but it is installed more securely than the original product. I will give my impressions again after driving.
View detail
Depending on the speed range, the rating...
The OEM Meter visor was somewhat more effective than it looked, but this product is very windproof and can increase cruising speed by +20 kmh, which is excellent.
But there is a problem. That is the interference and deformation of Screen's Meter due to wind pressure.
The stopping point of the Bracket isQuantity:Pair (for Left and Right) 1 item each (Co-tightened with Headlight's Stopper Bolt) The bracket is low relative to the screen, so the wind pressure will completely hit the Meter depending on the speed of the wind. Since the supplied rubber is not enough, we attached a 2mm rubber plate. Then, we can see that the Right Side, which does not have the Meter, is deformed by the wind pressure while driving.
I feel that the upper part of the screen needs to be reinforced with a universal bracket or something, but the screen width is narrow, so I would like to carefully determine if a universal bracket can be used.
View detail
It is easy to install.
The installation had good hole accuracy.
It was easy
The effect is not clear.
Maybe it's all the wind that's involved.
It may be.
View detail
Fits: HONDA CB1300 SUPER BOL D'OR, HONDA CB400 SUPER BOL D'OR
Windscreen
Very good i like and ships super fast. Make me addicted to it... wanna buy more stuffs here. View detail
Replacement from OEM Product
I replaced the OEM Product because its windproofing effect is nowhere near as good as it should be. View detail
Small Processing Required
Well nut holes are OEMΦ10, but this product had Φ9, so I machined them.
The rest is generally satisfactory.
View detail
Fits: HUSQVARNA SVARTPILEN401, HUSQVARNA SVARTPILEN125
Wind protection is moderate
I installed this product with the expectation of Wind protection against wind when driving at high speeds.
The effectiveness of the program was not as good as I had hoped.
Is the wind hitting the chest area somewhat reduced? It is about the same.
If protection effect is important, Long Type may be better.
To be honest, I thought that Svartpillen's design was the coolest in its original form, and I was a little worried about the looks of the product because the only pictures on the product page and the Manufacturer's Site were of the product in the up view, so it was hard to imagine it with the product attached. I was a little worried about the looks of the product, but when I actually put it on, it was much cooler than I imagined.
I will give more photos for the reference of others.
As for the quality of the product, it is not bad at all, but it would be nice if more work could be done on the edge of the Screen (there are some marks left on the edge of the Screen, like a cut).
When I try to insert the well nut (the one with the nut inside the rubber) into the bracket hole, it does not go in at all.
It is smoothest to insert the one with the flange by squeezing it.
The Bracket is assembled before the Screen is assembled, but the Bracket should be temporarily fixed to the extent that it moves lightly, and the Bolt of the Screen should be tightened evenly etc., and then the Bracket should be tightened at the end for successful attachment.
View detail
comfortable
Introduced as more and more high-speed long-distance bullet Twos are becoming available.
The Bolt is a little low if it is attached as it is, so a Spacer is used in the Bolt section to change the height of the Bolt from front to back and to make the angle more upright.
When the Speed is released, the wind pressure will cause it to fall asleep, so it is reinforced with Bracket.
Overwhelmingly comfortable.
View detail
Replacement from OEMLSize.
The shaking of the Helmet caused by the wind on my body when accelerating up to a speed range that I can't tell anyone about, is gone.
The Helmet is only a little shaky near the Motorcycle's speed limit.
As I basically do not lean forward, aerodynamic drag is considerably reduced and I feel more comfortable.
View detail
Chatter sound is terrible and unusable.
I do not trust ODAX products in general, but there were very few custom parts for the New ModelTMAX, so I had no choice but to choose this one. As I expected, the chatter sound during driving was so bad that I contacted the manufacturer once and was treated as a complainer. I contacted the manufacturer once and they treated me like a complainer and made me feel uncomfortable. No Chatter noise at all while driving. I should have bought the WRS one from the beginning. View detail
I wanted the Seal to be attached separately.
I understand the desire to put a 3D Seal of Manufacturer, but I did not like it and it was a little troublesome to peel it off.
I made it Short, so it is a good windbreaker.
It can be installed on a 21-year z900 without modification.
The strength of the screen itself is not inadequate.
Note that the OEM bolt used to hold the meter cover and the bolt used to install this product are different in hexagonal size, requiring a smaller tool than the OEM bolt.
Pushing the Large popular car model, we dared to choose the z900.
We can fully recommend to such eccentric people.
View detail