Reviews
Great Value and Quality Breather Hose Clamp for the Grom
About quality and texture: I am happy with the quality of the hose clamp from NTB, made from a spring steel with a nice silver trivalent chromate treatment surface finish. About the feeling of use: The Honda breather hose clamp is small and weak, the NTB hose clamp secures the hose much better and looks great with it's silver surface finish. Products to buy together: Some more hose clamps in varying in size would also be desirable to purchase along side the BC15.5 hose clamp. Difficulty of installation: The process to install takes just a minute, I find my fingers are usually not strong enough to install these hose clamps so tend to use combination plyers and add some electrical tape to the jaws so to not damage the surface coating. Not difficult to do. Cost performance and comparison with other products: Good costing as you are getting a great quality product for a very low price as compared to the hose clamps available from SP Takegawa. About shipping and packaging: Sea frieght was my perferred method of shipping due to the lower cost but currently unavailable due to Japan Post. Webike kept me updated on the status of my order up to when it shipped. The parcel arrived within the expected date range and was well packaged with no chance of the part being damaged. Any concerns, cautions, or advice when purchasing: I find the NTB applicable range a little difficult to workout for the sizing I am wanting but if you look at the photos they attach with the vernier it makes this much easier. View detail
Maru available in 1pc. units.
I bought this one to replace the hose clip with a firmly stop plate Spring type. I had no hesitation in deciding on this one because the narrower the diameter, the more limited the choices.
The NTB clamp is easier to pick up because the ear part is a little longer than the spring type clamps that are also found in Manufacture OEMs. The NTB is easier to pick up because the ear part is a little longer than the OEM. The price is lower than other manufacturers, and I am glad that I can buy it in 1pc. units.
View detail
Maru available in 1pc. units.
I bought this one to replace the hose clip with a firmly stop plate Spring type. I had no hesitation in deciding on this one because the narrower the diameter, the more limited the choices.
The NTB clamp is easier to pick up because the ear part is a little longer than the spring type clamps that are also found in Manufacture OEMs. The NTB is easier to pick up because the ear part is a little longer than the OEM. The price is lower than other manufacturers, and I am glad that I can buy it in 1pc. units.
View detail
Maru available in 1pc. units.
[How is it used? As hose clip around carburetor
Was the one you received as per Image? Yes
Was the installation difficult? Nothing particularly difficult.
How was your experience with it? Moderately firm and safe to use.
[Included Parts:were they on? No
[Was there anything that disappointed you? As expected
I bought this clamp because I wanted to replace the hose clip with a spring-type clamp that stops only when the clamp is in place. The NTB is easier to pick up because the ear part is a little longer than the OEM. The price is lower than other manufacturers, and I am glad that I can buy it in 1pc. units.
View detail
Maru available in 1pc. units.
I bought this clamp because I wanted to replace the hose clip with a spring-type clamp that stops only when the clamp is in place. The NTB is easier to pick up because the ear part is a little longer than the OEM. The price is lower than other manufacturers, and I am glad that I can buy it in 1pc. units. View detail
Wrong size
The clamp that holds the hose on the rear brake reservoir tank was rusted out, so I bought this to replace it, but I actually needed a larger one.
I had no choice but to replace the fuel filter clamp attached to the fuel hose, which was also damaged. The product itself is the same as the hose clamp sold at the gardening supply corner in the home center for about 1pc. 80 yen, but since I got it cheaper than that, I decided to call it good. It's very easy to use, just pinch it with radio pliers and spread it out while attaching it to the hose.
I bought the hose clamp for the reserver tank at Home center and installed it to the right size.
View detail
Hose clamp。
It's easy to grab and use. View detail
The price is per piece. The size is accurate. View detail
Good to have in stock.
I bought the Meteretc. without any commitment to it.
I'm a little disappointed that it's not in stock.
It's even better if these Parts are in stock and available for immediate delivery.
View detail
It stopped perfectly!
This time I used NTB's Hose clamp here to stop the Clamp part of the joint of Fuel Hose of Motorcycle (((O (* ゜ ▽ ゜ *) o)))
Since the installation position is a gap between Tank and Air cleaner box, there is worry that the environment of the installation position will not rain directly but it will rust soon, even though rainwater does not hit it He briefly blew the heat resistant Silver and tried installing it from blowing Clear which is not heat resistant from the top) ^ o ^ (
Size of Hose is also perfect, it is securely fixed, so even if you try to pull it a bit, it is stopped without problems and there is a sense of security.
In addition, I tried using the same thing for negative pressure Hose, but that can be used without problems.
In this type of Clamp, there are things that cracks may enter the Hose side or tears off the Hose if tightening is used for a long time, but there is one side which is somewhat molded in this Clamp I could not see the part that is likely to cause such a large Trouble. (We have not seen it for now)
Do you have any disappointing points?... As I thought, it is somewhat concerned that there are times when the knob part gets bent depending on the angle at which the knob part softly pinches as a disappointing point...
If you consider this softness to be exquisite softness that does not hurt by tightening Hose too much, you may be making it with this softness...
Several months have passed since installation, but since it can be used without problems, I think whether it is quite good product of COSPA for price.
Looking at the situation in the future, if there is nothing that will cause problems, I'm thinking about installing it on another vehicle.
I think that there are also many people who are not using Hose clamp because it is troublesome to attach or remove every time. (I was like that before)
It is too late after Gasoline leaked because Fuel hose got out of the way while you were running or getting your eyes off. How would you consider purchasing and installing on this opportunity?
View detail