Reviews
As a replacement for OEMBlinker relay
I bought a battered 900SS (900SL) and am Restore.
In this situation, RearBlinker decided to change to ultra-small type LED's for various reasons.
The front is a Cowl recessed type, but since this is part of the body design, it is used as is, and the light bulbs inside are not converted to LEDs, but are left as they are.
This would be a hassle with bulbs in the Front and LEDs in the Rear, but times have evolved and there is now ICRelay, which supports a variety of wattages and makes everything look good.
The problem is replacing that ICRelay with the original Relay.
For ordinary Japanese cars, it is a 2-pole universal layout, so all you have to do is plug in the Conversion Connector that comes with the Relay, but unfortunately, DUCATI is a 3-pole Relay.
In addition, the connector is fixed to the body of the car, and the Relay is inserted into it, which is the opposite arrangement from that of domestic cars.
(For domestic cars, the RelayBody is mounted on the car body, and the Connector extending from the Harness is inserted into it.)
So we decided to disconnect and discard the UniversalConnector (Female side) from Relay and make our own Conversion Connector that would be Male-Male.
After carefully checking the terminal shape of the OEMRelay, I realized that it is the same as the H4Headlight Connector.
So we purchased a Kit to create H4Connector.
Although the connector shape is correct, the H4 terminal and the OEMRelay terminal have different widths.
The OEMRelay terminal width is about 6.4mm, and this H4 terminal is about 7.7mm wide, about 1.3mm thicker, so Quantity:Pair (for Left and Right) and shave 0.6mm each to make it ready.
However, the terminals are generated by folding a flat plate 180° with PRESS, so if both ends of the terminal are shaved, the folded part is lost and becomes RoseRose.
To avoid RoseRose, before shaving both ends, solder is poured inside the terminal to fix the PRESSED board firmly in place, and then both ends are shaved...Relay terminal is completed!
We were able to connect the Relay receiving Connector on the car body side and the replaced ICRelay Connector while converting well.
This time, the terminal included in the H4Connector set was the only one that worked without failure, so it did not come into play, but I purchased it as a spare in case the work failed.
Ordinary zinc-plated terminals (not gold-plated), very ordinary in shape and strength.
It is often used in the Connector for Large current, so it is a good idea to have it as a spare so you do not have to struggle in case of an emergency.
View detail
I purchased and used it with Male out of necessity.
To be honest, I am at a loss to explain or comment on these parts, but they are working normally.
I am posting this because I think there are quite a few people who Review.
View detail
I needed it so I bought it with Female
If only it were cheaper …! I thought it would be cheaper, but I needed it fast, so I bought it.
Good quality!
View detail
Beware of Size Mistakes
[How is it used?
When replacing the blinker of XJR400R, I had to cut off the Bullet Terminal of the blinker to pass the wiring through the blinker bracket, so I needed a new Bullet Terminal.
How was your experience with it?
The Bullet Terminal could not actually be used because it was not the same size as the original Bullet Terminal.
How did it compare to other products?
The Size I wanted to buy was available at Home center for the same price, so this product is not a special bargain.
[Points to note]
The number of pieces was not listed here, but the Quantity:1 Set of 10pcs.
Items to buy together:Electric Works Pliers
View detail
090 type terminal for Coupler
I bought a Male to get power from the FrontServiceCoupler- on my PCX150KF30.
Type 090 terminal.
There is no problem at all to install and energize the Wiring.
Waterproof Cap and Terminal are Quantity:There are 10 sets in the package, so it can be used as a spare.
View detail
It's an itch I can scratch Target components
For the GSX-S125's Attachment power supply, it is used in conjunction with the Failure Diagnostic Connector to I bought this Connector to pull it in
(Take the Yoshimura's Temp meter power supply out of this Connector)
So-called 090 Water-proof type of terminals and general 0.5sq Response
Quantity:1 Set of 10pcs. so there's plenty of room for failure to a certain extent, and if there's any left over, you can save it for future use The amount that can be kept
The product name is Quantity:Set, but this is just a "Terminal + WaterproofRubber That means
Hence the "Male and Female Quantity:Please note that it does not mean "Set"
(Specify "Male" or "Female" at the time of purchase.)
And, of course, just because you bought this "With a pong is not possible
Crimp work using Electric Works Pliers is required, so this point Also note
View detail