Reviews
Mount expansion foundation with no gap required
[How is it used?
Used on the Clutch Side of CBR250RR (MC51) from April 11, 2020 to October 2, 2023.
Mount the iPhone miniSeries using the following parts
1.RAM MOUNTS BallMount M10xP1.25:https://www.webike.net/sd/24021956/
2.RAM MOUNTS Short arm:https://www.webike.net/sd/21313052/
3.RAM MOUNTS XGrip (M) Smartphone Holder (maybe):https://www.webike.net/sd/22558592/
4.Large amount of Screw Lock agent
Was the one you received as per Image?
The product is exactly as shown in the image.
Was the installation difficult?
I forgot to measure the distance between Bolt.
BoltQuantity:I guess it's easy enough to remove and replace the 2pcs and install. Since I feel there is a gap at the bottom, it may need to be filled with Washer or something.
How was your experience with it?
The Smartphone Mount is a good choice because it requires far fewer unnecessary parts than a dedicated bar.
Since it is installed by replacing the original parts, there is no need to consider the gap between handlebars, etc., unlike retrofit Mirror Holderet etc. The original bolt can also be used.
Smartphone mounting is possible with far fewer wasted parts than with dedicated mount bars, etc.
After mounting the ball on the car body, I shook it with the ball, and the car body shook, so it seems to be robust.
I don't remember how many times I actually ran with my phone on it.
Riding the phone on the Clutch (Left) side rather than on the Brake (Right) side met the request because I prefer the LeftMount for the possibility that the phone could escape to a non-roadway in case of an emergency.
[Included Parts:were they on?
Included Parts:None, only this product wrapped in Vinyl
[Was there anything that disappointed you?
I think I used a similar part from YAMAHA for the R6 Brake because of the similarity.
YAMAHA 5YU-26393-00:https://www.webike.net/sd/25729937/
That one did not occur when the gap was R6.
[Notes]
This product Mirror Holder It is used like the CF POSH Universal mirror holder (https://www.webike.net/sd/1125900/), but it does not say anywhere that it is for smartphone mount.
View detail
Required for Mirror installation on Racer
When running a foreign Enduro racer on public roads, the NORMAL does not have a Holder to install Mirror. Replacing it with this will solve the problem. View detail
Mirror Holder
I bought this to put Mirror on a MASTER I received.
Too bad they didn't have the same color.
View detail
Screw hole position required!
Because I changed to Nisshin's Radipon, the position of Mirror Holder became asymmetric between Clutch Side and Brake Side.
However, it is not possible to install it as it is because the hole position does not slightly match with the Kawasaki OEM clutch side of our model. (It is necessary to extend the hole position by a few millimeters)
I had no choice but to order a Kawasaki OEM Mirror Holder to solve the problem. I think the quality of the product itself is perfectly fine.
You better check the Screw hole Pitch when you buy it!
View detail
Be careful with the dimensions!
Radiphone introduced, but Quantity:Pair (for Left and Right) I bought it because the Mirror position has changed in
The Clutch Side can also be made with Mirror Holder to make the quantity:Pair (for Left and Right) However, I couldn't install it because the dimension of screw hole is a few millimeters different from Kawasaki OEM Clamp.
If the Screw hole position is widened with File etc., it is possible to install it, but I was worried about the strength, so I bought a Clamp with Mirror Holder of Kawasaki OEM and solved the problem.
There was nothing wrong with the product itself, I just didn't do my homework.
View detail
After all it is not JAPAN
? 【What made you decide the purchase?】 Since cheap analog products have broken, I selected a Manufacturer item.
? 【How was it actually used?】 I am firm and secure.
? 【Was it difficult to install? (Hard parts case)】 it's simple.
? 【Please tell me the point of installation and hang (in the case of Hard parts)】 Since there is a possibility of cracking if it narrows too much, it would be better to use Torque wrench.
? Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) 】Any
? [Is there anything I was disappointed about?] None. It was as expected..
? [Request to Manufacturer - Please tell me if there are any improvement points】 No particular.
? 【Have you compared items?】 None.
? [Others] Many inexpensive products mimicked just the form, but again I realized that the price and the quality are in proportion.
View detail
It is good for various Bracket
I bought a RadarBracket for installation. Last time, No Manufacturer item Quantity : 1 Set of 2pcs. Although I purchased, the Screw division caused a crack. Especially, Motorcycle thinks that Brand that is reliable with quality emphasis is good because vibration and impact of road surface are transmitted via Frame. Dropped out while driving - It is heavy Large when it is involved. View detail
Clutch side, required processing
With the ZA-9R E type becoming NAKED, Quantity : 2pc. Purchase Set.
Although there is no discomfort with almost the same color shade as the OEM color after the above model change over the years, on the Clutch side Screw Pitch is different so we installed it by File.
However, Mirror installation angle, or Quantity : Pair (for Left and Right) Care must be taken because the Lever angle will not be delicately matched.
As it is still running, it is an important part so we recommend that Left Side also be fitted with exclusive items matching Screw Pitch.
I am satisfied with Large change regarding products.
View detail
Processing required for installation
Left Mirror Holder breaks at high speed. Last time, RightMirror Holder is broken so it's the second time. Is it due to the vibration of KATANA. Select from OEM's Nisshin. When I install it, the hole does not match delicately. OEMRepair Parts I'm dissatisfied with Large. The previous thing was a long hole and fine adjustment was possible. Is this also Reduction in cost? Be careful when purchasing. View detail
It is not possible either.....
With ZX-14R ABS bush hanging
I used it for processing ClutchReserver tank
Outside the mirror section
It is the same shape as the OEM, but the color tone is different
It is a little disappointing.
View detail
Mirror has gone up.
I bought it for installing Kawasaki OEM Radial master.
I could install it without any problems, but because the installation position of Mirror changed and I attached the Opposite Thread Screw Adapter for Yamaha OEMMirror, the Mirror of Right has come to protrude upward.
I think that attention is necessary when attaching Yamaha OEMMirror.
View detail
Screw hole position changed with round bar file !!
I bought it to install Mirror on Left.
Position of Screw hole slightly different from Clutch lever side (About 2 mm) So I changed the Screw hole position with round bar file and changed it.
View detail
Mirror is Quantity : Pair (for Left and Right) Symmetrically!
Mirror installation position is Quantity : Pair (for Left and Right) I thought that it would be symmetrical and purchased.
When looking at it, there is less reflection of shoulder, you can check backwards without discomfort! I am satisfied.
Slightly higher Left Side but it is acceptable range.
View detail
Repair Parts
It is purchase when purchasing MASTER of semi radius.
As a result, Cliamp with Mirror hole in semi radiator MASTER is also
I did not use it because it was included.
I think that there is no problem on the product.
View detail
Because it was MASTER you got second hand ...
【What made you decide the purchase?】
Because I wanted to match the color with the need of Mirror Holder.
【How was it actually used?】
Because it is a part that I do not have the choice, I am satisfied with OEM? Repair Parts.
【Was it difficult to install? (Hard parts case)】
It is not difficult because it is only tightening the Bolt of the M8.
【Please tell me the point of installation and hang (in the case of Hard parts)】
Since it is also the part that determines the fixed position of the operation Lever, it is necessary to position it towards the user.
At that time, positioning with Bolt on top, fastening with specified Torque, followed by Bolt below is concluded with Torque.
[Is there anything I was disappointed about?]
It's a part I do not have the choice ... I felt a little expensive.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Because it is out as Repair Parts, I'm happy that selling Cost will go down a little more.
Although it is not said that it is half price, it is saved if thousand yen is fixed price base.
【Have you compared items?】
There is none.
Or, since I was using Silver before ProductNo, I wanted to match the colors anyway.
[Others]
Of course, this part was attached to the Master cylinder you got second hand, but there was no Mirror Holder, so Bracket of Reserve tank could not be installed.
As we were seeking fixing with Mirror Holder, we decided to exchange this by using this Silver.
However, it will be tight if the colors match.
View detail
[WeBike Monitor] It Bound tight too much and has been divided into two. Special attention is required to a Torque. Since it was its carelessness this time, it is unavoidable. It was not bad at all in product, and carried out. It is a Recommen
[WeBike Monitor] It
Bound tight too much and has been divided into two.
Special attention is required to a Torque.
Since it was its carelessness this time, it is unavoidable.
It was not bad at all in
product, and carried out.
It is a Recommendation at the Accent of the circumference of the
Handle.
View detail
It purchased in order to Handle-mirror-ize Ninja1000! Since 1152 was touch as the slightly high kana ? now although the direction besides was written, but there is also no substitute in others and he bought it with bulk purchase 1129 as at a low pric
It purchased in order to Handle-mirror-ize Ninja1000! Since 1152 was touch as the slightly high kana ? now although the direction besides
was written, but there is also no substitute in others and he bought it with bulk purchase 1129 as at a low price as possible, it is the good kana!?
View detail
[Webike Monitor] It is not for Mirror attachment this time [ ], Jupiter It purchased in order to transfer the Control switch for Navigations to the position nearer to the thumb using Tech-mount ZZZ-0257 and GALE SPEED Tank-stay Type4 for the improv
[Webike Monitor] It is not for Mirror attachment this time [
],
Jupiter It purchased in order to transfer the Control switch for Navigations to the position nearer to the thumb using Tech-mount ZZZ-0257 and GALE SPEED Tank-stay Type4 for the improvement in operativity.
Since it was not able to move to the position which considered though it was regrettable, it is not used.
View detail
[Webike Monitor] Since the Cowl was removed, it purchased for the Mirror move. Since it was the Separate handle, there are no Spaces, such as a Mirror-clamp Holder, at a posterior matter, it used effectively for the existing Parts, the Mirror cou
[Webike Monitor] Since the
Cowl was removed, it purchased for the Mirror move.
Since it was the
Separate handle, there are no Spaces, such as a Mirror-clamp Holder, at a posterior matter, it used effectively for the existing Parts, the Mirror could be transferred, and it was saved.
View detail
Since the Bar handle was used, it purchased. Since the Brake of the Nisshin which shines just from the first can be used, COSPAR is good.
Since the Bar handle was used, it purchased. Since the Brake of the Nisshin which shines just from the first can be used, COSPAR is good. View detail