Reviews
For Meter Bulb in 6V vehicles
When I went out shopping at night with my Yamaha CHAPPY that I had restored, I could not see the Meter at all and thought it was out of bulbs, so I immediately purchased one.
YamahaOEM Parts are still available, but at a slightly higher price.
I looked up 6V3W and found this product, and since it was inexpensive and in stock, I snapped it up.
10mm BoltQuantity fixing Meter:Remove the 2pcs and the meter cable to access the wiring.
I replaced it and put it back together, and when I started the Engine, the Meter Bulb came on successfully.
Since it is 6V, it is naturally dark, and to be frank, you can only vaguely see the position of the needle when driving at night.
I don't plan to go far, so I'm satisfied that I can see for now.
View detail
Normal is fine.
Tail lamps that are always on are consumable.
Stop-lamps are still alive but replaced immediately when noticed to avoid maintenance failure due to trivial things.
We had thought about using LEDs, but we concluded that Standard was the best choice due to its cost performance and reliability.
In the case of DJEBEL, the OEM installed Carrier interferes with the approach of the Tail lamp cover to the Screw. This is where SEA BASS comes in:remove the rear screws from the carrier, loosen the front screws, and stand the carrier up like a Gal wing, and the replacement can be completed in a few minutes.
The durability of the bulbs is a matter of luck, but since it is a product of FOR JAPAN MODEL MANUFACTURER, it is safe to use for the time being.
View detail
Tail lamp replacement for JOG for repair.
Tail lamp bulb of a 2-stroke JOG obtained through a private sale was broken and was replaced.
Lower price than Valve for OEM Parts, Quantity:1 Set of 2pcs.
I will only use 1 pc. and will keep the other one as a spare.
I thought about using LED Tail lamp bulbs, but since it is a 50cc moped, these are sufficient.
*Wattage should be matched to the OEM.
View detail
A very ordinary Halogen bulb.
Whenever I buy a used Motorcycle, I always replace all the valves with new ones, but since they were out of stock at my local store, I couldn't be bothered to come back to the store, so I bought them by mail order.
I thought the price might be a little higher than the actual store. I thought the price might be a little higher than in the actual store, but considering the time and effort involved, it was acceptable.
There is nothing wrong with the fit and there is nothing special to say about the color.
This is fine unless you don't want the Amber color to stand out over the Lens.
I thought it might be a good idea to purchase an additional one as a spare when I purchase some more Parts.
View detail
It is safer to always have it at home with Spare!
The cheap Pine Stripe bulbs, but just one of these can cause a maintenance failure!
They run out without notice, so it's always safer to have one in reserve.
Depending on the model of car, the replacement work is a single +Driver.
View detail
Rare 6V bulb
I used it to repair a broken Neutral lamp on a VANVAN90 that was given to me by a friend's father.
Since it is an old motorcycle, there are no parts available, so the rare 6v bulb is a big help.
View detail
The abundant number of Watt will help.
I added Hazard and bought this one to lower the Watt number in terms of power consumption reduction.
It was really helpful to have Double Bulb as well as Single Bulb.
The abundance of Variation here is very good, as Motorcycle definitely does not look good with flashing LEDs.
View detail
Cost-effective
Used for POSH and Fath blinkers. POSH has Valve, but I bought this one because Mats Stripe products are much cheaper even though they are the same standard. I have used them on other cars and have confirmed that there are no quality problems, so I can use them with confidence. View detail
For Meter Bulb
I purchased this for my 4LMONKEY Meter Bulb.
If you like the old-fashioned way, this is the way to go, as it is not as flashy and bright as LEDs.
View detail
No problem and safe. Just be very careful about the angle and shape of the mouth Gold.
For the Tail lamp, we avoided LEDs so that the power generated would be used properly in combination with the power consumed.
I hear that it is not good to have too much surplus electricity because once electricity is generated, it can only be converted into heat, etc. at the Regulator.
The Headlight is always on and off and I thought it would not be affected by the LED, but the Tail is always on, so I left the White hot bulbs on.
Made by Pine Stripe, no question about it...White heat bulbs are becoming a component that I'm thankful they still manufacture.
We kept one as a spare just in case.
View detail
Stable M&H.
I have no complaints about the quality and price. View detail
Thank you for the quick delivery.
I haven't installed it yet, but I'm happy that it's delivered safely. I'd like to leave anywhere if I could imagine a w800 that would fit well. If the delivery is a little late because the webike is out of stock, the delivery will not be too late! View detail
Reliability Large for a quick fix
I bought it to repair the Tail lamp of the commuter car which had been cut before I knew it. I thought about LED for a moment, but when I think about the reliability of the cost and delivery time, the large thing is that it arrives sooner than anything else and can be fixed quickly.
It's a bit pathetic that if you buy two balls, one is out of stock, but the product is reliable.
View detail
Valuable 6V light bulbs
I am glad that you continue to produce the precious 6V bulbs.
Used for Restore of SportsCUB.
Durability and other factors are unknown as we are about to test it.
The slightly higher price is unavoidable given the production numbers.
By the way, it is not related to the product itself, but one point is noted.
Check the application carefully when buying old Car bulbs.
It's very easy to make mistakes.
View detail
I'd like to have one in reserve.
Used in LITTLE CUB for Blinker.
This time we had to replace it after it ran out of bulbs.
I'll have one in case of an emergency.
It's a great price to buy.
View detail
It's cheap
I bought this for Replacement because the Meter Bulb in my 1979 CD125 ran out. Installation and lighting was no problem. 6v is still a net purchase. View detail
Used in CB50S Restore
I used it when I converted my CB50S to 12V.
No problems and normal brightness.
The Regulator failed and the voltage was so high that it went out immediately, but under normal circumstances it would have worked fine.
View detail
Used in CB50S Restore
I used it when I converted my CB50S to 12V.
No problems and normal brightness.
The Regulator failed and the voltage was so high that it went out immediately, but under normal circumstances it would have worked fine.
View detail
Stop lamp
I bought it because the stop lamp ran out
It's just a plain, ordinary Valve
It can be used for stop/stop-lamp because it is a Double Bulb
Lately, though, I've been noticing sequential and SquidRing, and these bulbs themselves, like these bulbs It's not often you get a chance to see Valve
This one has a warmth to it, and when it cuts off occasionally, you can polish off the Lens cover and Reflector It's a great motivator and a great opportunity for maintenance
I don't think I'll be going LED for a while
View detail
I'm very happy with the price and it lights up properly
I was looking for a tail lamp bulb of SR400, and Small size was not available I bought this Manufacturer Hit and it was a good price View detail