Reviews
The quality and shape are awesome, and it only takes a couple of minutes to install it in Lever with the right tools!
You will need:cotton swabs, appropriate grease, Tweezers, 2?pin punches, and Hammer
Align the holes in the Lever with the vertical direction
Take a small amount of Grease on the tip of a cotton swab and apply it to the press fitting area
After painting, insert the Adjuster Knob into the pot and align the holes
Grasp the roll pin with Tweezers and place it in the hole
It's easy to get in with a 2? pin punch and a hammer
Other imprecisions said it was difficult to press-in, so I had to get my tools together before I did it
You can buy a 2?pin punch at Straight for 200-300 yen
Cotton swabs, Grease, Tweezers, and a hammer were the things I had on hand
I used Silicon grease for the Grease
Notes
You need someone to hit the first one or two shots
It is possible for one person to do this if a little roll pin is put in
View detail
Installation is pretty annoying
I had read in the Review that the installation is Large strange, but it is difficult to install than the imagination It was the first time
The adjuster piece is fixed with a pin, but the pin is not as large as the size of the hole It is necessary to press-fit it because it is large
I tried to get it in with all my strength, but I couldn't
Cool the pin in the freezer, and heat the hole side with a Dryer to expand it I was able to make it if I did
It may not matter that I chilled and warmed up, but I hope it's a comforting reference
View detail
I think every time I buy it
I feel that the price is as high as 300 yen,
It is strange that it is sold separately with Lever than anything else.
You can convince if you bundle a piece of the same color with Lever and raise it for 300 yen
Lever can not be attached during periods when it is sold separately and can not be purchased due to out of stock etc..
But I will not install it if it is not, so I bought it this time too
View detail
Adjuster pieces are necessary for using a lever.I had no choice but bought this product separately.It doesn't seem that only I think that this purchase style is annoying.Is this to make no need to purchase anything other than a lever in re
Adjuster pieces are necessary for using a lever.
I had no choice but bought this product separately.
It doesn't seem that only I think that this purchase style is annoying.
Is this to make no need to purchase anything other than a lever in repair ?
As I already noted in a review of a lever,
this products are 6 position-adjustable. Besides, OEM is not. I think it is superb!
It can adjust even such a lever touch as the glove thickness causes
by moving one position.
I greatly appreciate the high quality than OEM.
I wish a repair part set would be on sale that includs a lever and adjuster pieces for each car model.
As seen in the picture, a worker without experience might damage the body with a tool
when installing an e-ring to be used in building in adjuster pieces
or installing an OEM knocker to be used in a master cylinder.
A lever built in all necessary parts
would eliminate such anxiety on purchase from those who are not skillful with their fingers.
I put four stars because I felt slight unkindness.
I myself enjoyed the installation.
View detail
When it is the right fall in which a MASTER breaks, since this Parts flies almost certainly, if it is a Circuit, it cannot be searched for (bitter smile). since the Push rod of a MASTER is also almost useless in case of breakage that this Parts flies, th
When it is the right fall in which a MASTER breaks, since this Parts flies almost certainly, if it is a Circuit, it cannot be searched for (bitter smile). since the Push rod of a MASTER is also almost useless in case of breakage that this Parts flies, this Parts should also be just attached to the Push-rod Kit purchased for a Repair, but it is not considerate -- (?) -- it is not attached to things. Therefore, if it corrects at any rate, I will regard sex appeal as it being a Parts good for the direction ... View detail
Fits: YAMAHA FZ1, YAMAHA FZ1 Feather, YAMAHA FZ1, YAMAHA FZ1 Feather
"Since the lever of normal is cheesy, I exchanged. Since I have many experiences of lever exchange, I was inattentive. Although the clutch side was easy, a power was required a little for the brake side. Since there is no root part of normal and it had st
"Since the lever of normal is cheesy, I exchanged. Since I have many experiences of lever exchange, I was inattentive. Although the clutch side was easy, a power was required a little for the brake side. Since there is no root part of normal and it had stopped at the bolt by the rivet, it had written in the description that it is deleted by a grinder, but I turned over forcibly by the slotted screwdriver etc. In terms of a texture or a style, it is dramatically pleasing. A span of adjustable range of stepless adjuster also becomes detailed and it is good." View detail
they are difficulties for pressing the pin for adjuster piece fixation fit in a lever main part, although it is parts which do not change if it exchanges for the billet lever of an antlion and will not equip by a set -- there is also no fear of separating
they are difficulties for pressing the pin for adjuster piece fixation fit in a lever main part, although it is parts which do not change if it exchanges for the billet lever of an antlion and will not equip by a set -- there is also no fear of separating from it, if even fixation also of ... is possible.
Since the span of adjustable range is wide more than pure, and it can unite with a favorite lever position, they are recommend parts.
View detail