Reviews
Front Fender Side Decal ZETA Racing
The size is too large to put on KX85Front Fender. View detail
3pcs in 1set, before quantity:Pair (for Left and Right) Cost-effective and can be affixed to
[How is it used?
Dress-up of my car?
Was the one you received as per Image?
I think it is as per Image.
How was your experience with it?
Some places to paste the Number Plate may be curved, so it is better to paste the Number Plate on a flat surface if possible,
[Points to note]
The area where the Number Plate is to be applied should be degreased and wiped clean.
How was your experience with it? As mentioned in the previous section, it is better to use a heat gun to warm up the paste before slowly applying it to places where the paste surface is not flat or curved.
How did it compare to other products?
The price is low and there are 3 pieces in 1 SET, so Upper Cowl and Quantity on the front:Pair (for Left and Right) It is good because it can be attached to the Cowl of
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
It is recommended to degrease and wipe the area to be used for affixing the Number Plate beautifully in advance.
If the surface is not flat or curved, it is better to warm it up with a heat gun before applying the paste slowly.
View detail
Upgrade suspension
Good for dress-up around the rear area.:Rather than gray, it is more in tune with the color of the Swing Arm and is closer to silver. It is thick and durable. View detail
for RaceNumber Plate
[How is it used?
I purchased this as a SIDE and UnderNumber PlateSticker for Road race.
How was your experience with it?
I usually use a Number Plate Sticker from KITACO, but Webike discontinued it, so I looked for something close and bought it. 9 was the Number Plate, but Sticker 6 was in stock, so I used 6 upside down.
How did it compare to other products?
I think the numbers are longer and narrower than the Sticker I used to use, perhaps for Off purposes? I think the numbers are longer and narrower.
Also, the thickness of Sticker seems a bit thick.
[Points to note]
When I put it on the part with R, air gets in and it is hard to put it on well, so I use heat gun and struggle more than usual Sticker.
Especially, when I want to sticker to Seat Cowl, my Motorcycle needs to cut the sticker,
I had a hard time putting it on well. (Even after it was pasted, the workmanship was not good.)
View detail
The usual Number PlateSticker was discontinued.
[How is it used?
I purchased this as a Front License PlateSticker for Road race.
How was your experience with it?
I usually use a Number Plate Sticker from KITACO or similar, but Webike had discontinued it, so I looked for something close and bought it.
How did it compare to other products?
I think the numbers are longer and narrower than the Sticker I used to use, perhaps for Off purposes? I think the numbers are longer and narrower.
Also, the thickness of Sticker seems a bit thick.
[Points to note]
When I put it on the part with R, air gets in and it is hard to put it on well, so I use heat gun and struggle more than usual Sticker.
View detail
Better to check before installation.
[How is it used?
Good because it is as per Image.
Was the one you received as per Image?
A few years had passed.
Seal surface is floating.
It was deteriorating.
I should have checked before installation.
There were two pieces in the package and one of them was beautiful.
After making a cut in the paper in the Seal section of the Reverse side.
Seal floating (with air bubbles)
I found it difficult to return the product because I noticed the
I applied it, but air bubbles are still noticeable.
Was the installation difficult?
Difficult to position.
Slightly, Quantity:Pair (for Left and Right) I wonder if the position of the Gap
How was your experience with it?
Good feeling
[Included Parts:were they on?
None
[Was there anything that disappointed you?
If it's new, it should be free of air bubbles.
I think, so Decal is only the first one.
I can't see it, so after I bought it, it's overlapping.
I understand the second check.
If possible, after a few years have passed.
I just wish you could have checked.
View detail
Shape is fine.
Used on a 2023 CRF250L.
The three-part design makes it easy to install by avoiding the difference between the three sections.
Normally I wouldn't be concerned about this, but looking at the recent HRCWorks bodies (AMASeries' WorksCRF), the placement of DID and Renthal's Logo is Quantity.:Pair (for Left and Right) The DID comes on the Axle side of the Rear wheel, but this product is reversed. Earlier Works bodies have the same arrangement as this Sticker.
If you don't mind such details, it is a good idea to protect the Swing Arm.
View detail
Just a little something...
The DirtFreak stickers are special:they are shaped to fit along the front fender and can be applied on slightly uneven surfaces without any problem, have good adhesion, and are of a perfect thickness. The quality is excellent for the price. Parenthesis is definitely better than the unintelligible Sticker. View detail
For off-road scratch prevention and dress-up appearance!
The material is thick and seems to be durable. I like the design, but it is not reapplicable, so be careful! View detail
Parenthesis is better
It is thick and seems to be durable.
Parenthesis is now better.
View detail
For Dress-up
I had installed the Clear type before, but the direct sunlight made it yellowish, so this time I used Material:I chose the Carbon Style one.
It is thick Decal and seems to be durable.
Since the adhesive is strong, it must be firmly positioned and applied when installing.
It is good because it does not come off even if it gets rained on.
View detail
Thick Decal.
I put the Large size on the side cover and the Small size on the front fender of KLX125.
I have used it for 3 years and it has not peeled or faded.
It is thick and seems to be durable.
View detail
Buy for Race
I'm going to participate in HappyEnduro, an off-road Enduro race!
So, we needed Number Plate and purchased this product.
It contains 3 pieces per set, Front mask and Quantity:Pair (for Left and Right) The number seal could be pasted with the number seal of the
I have a CuttingMachine at home, but to be honest, it's a hassle, so I'm very grateful to be able to buy it this way.
View detail
Good quality!
Good quality! The quality is good. The appearance of the shock absorber, which lacks 2%, feels full, and it feels like wearing a top-quality shock absorber!!! View detail
Nice webshop
I like OEM parts. Everything was delievered as aspected. Shiping as aspected. I will return when they have been assembled View detail
I put it on Swing Arm.
Because the Sticker which had been pasted before faded, Swing ArmQuantity of KLE250 as well.:Pair (for Left and Right) The size is also Match. View detail
Carbon color is difficult…
I used to use the clear type on my previous motorcycle, but I decided to use the carbon type for my new motorcycle to give it a more custom look.
In addition to the super strong adhesion like a mouse removal, the overlapping part of Clear was transparent and inconspicuous, while the gap of Carbon is not deceivable!
From the side, you probably won't notice it, but Parenthesis is good, Recommendation!
View detail
for Race.
[How is it used?
I bought this for the Enduro race.
I usually have someone with a CuttingMachine cut it for me, but I realized at the last minute that the number was different than usual and panicked and chose this product. I'm glad it was in stock! Thank you WehBig.
Was the one you received as per Image?
As per Image
Was the installation difficult?
Just stick it on.
Because it was 2 digits this time, it was easy. Sometimes, if it is a popular course in the FUNClass of JNCC (such as the old Mt. Yaga), because there is a case of 4-digit Number Plate, it is better to match the place once if it is possible to paste.
How was your experience with it?
I am satisfied with the easy-to-read Number Plate.
Some people often make a dirty Number Plate with Vinyl Tape or Gum Tape, but since it's hard for the Race tallying Staff to check, I want them to be cursed with not being able to get around because of Stack or MachineTrouble happening. It's really annoying. Don't compete in Level.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
It's always nice to have a good inventory.
View detail
It's solid
It's pretty thick and solid, so I think it's well protected.
I bought it because I wanted to make the front fork of CROSS CUB black, but I am satisfied.
View detail
I can use it normally
You can put it on your motorcycle or Helmet when you have an Enduro or RALLY50 I'm using it 。 You need to be careful not to cut the inner part of the corner when you remove it from the backing board because it is easily cut There is I think it could be a little cheaper, but I guess the packaging materials etc. are expensive View detail