Reviews
for RaceNumber Plate
[How is it used?
I purchased this as a SIDE and UnderNumber PlateSticker for Road race.
How was your experience with it?
I usually use a Number Plate Sticker from KITACO, but Webike discontinued it, so I looked for something close and bought it. 9 was the Number Plate, but Sticker 6 was in stock, so I used 6 upside down.
How did it compare to other products?
I think the numbers are longer and narrower than the Sticker I used to use, perhaps for Off purposes? I think the numbers are longer and narrower.
Also, the thickness of Sticker seems a bit thick.
[Points to note]
When I put it on the part with R, air gets in and it is hard to put it on well, so I use heat gun and struggle more than usual Sticker.
Especially, when I want to sticker to Seat Cowl, my Motorcycle needs to cut the sticker,
I had a hard time putting it on well. (Even after it was pasted, the workmanship was not good.)
View detail
The usual Number PlateSticker was discontinued.
[How is it used?
I purchased this as a Front License PlateSticker for Road race.
How was your experience with it?
I usually use a Number Plate Sticker from KITACO or similar, but Webike had discontinued it, so I looked for something close and bought it.
How did it compare to other products?
I think the numbers are longer and narrower than the Sticker I used to use, perhaps for Off purposes? I think the numbers are longer and narrower.
Also, the thickness of Sticker seems a bit thick.
[Points to note]
When I put it on the part with R, air gets in and it is hard to put it on well, so I use heat gun and struggle more than usual Sticker.
View detail
Better to check before installation.
[How is it used?
Good because it is as per Image.
Was the one you received as per Image?
A few years had passed.
Seal surface is floating.
It was deteriorating.
I should have checked before installation.
There were two pieces in the package and one of them was beautiful.
After making a cut in the paper in the Seal section of the Reverse side.
Seal floating (with air bubbles)
I found it difficult to return the product because I noticed the
I applied it, but air bubbles are still noticeable.
Was the installation difficult?
Difficult to position.
Slightly, Quantity:Pair (for Left and Right) I wonder if the position of the Gap
How was your experience with it?
Good feeling
[Included Parts:were they on?
None
[Was there anything that disappointed you?
If it's new, it should be free of air bubbles.
I think, so Decal is only the first one.
I can't see it, so after I bought it, it's overlapping.
I understand the second check.
If possible, after a few years have passed.
I just wish you could have checked.
View detail
Shape is fine.
Used on a 2023 CRF250L.
The three-part design makes it easy to install by avoiding the difference between the three sections.
Normally I wouldn't be concerned about this, but looking at the recent HRCWorks bodies (AMASeries' WorksCRF), the placement of DID and Renthal's Logo is Quantity.:Pair (for Left and Right) The DID comes on the Axle side of the Rear wheel, but this product is reversed. Earlier Works bodies have the same arrangement as this Sticker.
If you don't mind such details, it is a good idea to protect the Swing Arm.
View detail
For off-road scratch prevention and dress-up appearance!
The material is thick and seems to be durable. I like the design, but it is not reapplicable, so be careful! View detail
Buy for Race
I'm going to participate in HappyEnduro, an off-road Enduro race!
So, we needed Number Plate and purchased this product.
It contains 3 pieces per set, Front mask and Quantity:Pair (for Left and Right) The number seal could be pasted with the number seal of the
I have a CuttingMachine at home, but to be honest, it's a hassle, so I'm very grateful to be able to buy it this way.
View detail