Reviews
I'm being dry, but ...
First of all, installation is quite troublesome, especially if the Rear Carrier and Box are installed.... WiringCover- and Boots are not included for the high price. Although the wiring retractable part is designed to minimize water intrusion during mud splashing, there is a slight gap, so the part was treated with coking. After installation, it looks more expensive than other products (in fact, it is expensive...) and Parenthesis is good. View detail
Fits: HONDA CB1100, HONDA CB1300SF, HONDA CB400SF, HONDA CBR1000RR, KAWASAKI Z900RS
unconcernedly
It is not noticeable, but I was satisfied with the texture. View detail
Replaced by 70mm→90mm
I purchased the 70mm, but because it was too short, I replaced it again with a 90mm.
I installed it on her Motorcycle ….
Material/quality is great, but the non-slip GizaGiza is quite Large,
The end side (outside) of the footpeg hooks onto the bottom of the Boots.
If you are not careful, you may get caught when lowering your foot and not be able to pull it out...
As a countermeasure, I wrapped several layers of masking tape around 2-3 cm from the edge to eliminate GizaGiza,
Vinyl Tape is then wrapped around the GRUGRU to eliminate the bumps.
As a result, he said, the back of Boots did not catch and it was easier to get his feet out of the way.
Maybe you don't need GizaGiza for the footpeg end.
Maybe I should take a sander and scrape it off...
View detail
Measure the length carefully.
[How is it used?
When I changed the silencer of YAMAHA XJR400R from MotoGEARΦ100 to K2tecΦ86, the original spring was too long to fix the exhaust pipe and silencer.
So I thought that around 65mm to 75mm would not be a problem and purchased this product.
Was the one you received as per Image?
It was as shown in the Image, but it was surprisingly short... However, I thought that Spring should be stretchable, so I installed it, but it was not surprisingly stretchable.
I was in a tight-fitting state.
How was your experience with it?
I put it on, but it was so tight that it looked like it was about to snap, so I stopped using it...
I think the product is well made and good.
[Points to note]
Everyone should measure the length carefully before purchasing.
View detail
Beautiful
I think it's nice and clean with a luxurious feel. View detail
Fits: HONDA CROSSCUB50, HONDA CROSSCUB110, HONDA CT125, HONDA DAX125, HONDA GROM, HONDA CB250R, KAWASAKI Z650RS, HONDA CB125R, HONDA CB125R
It looks GOOD!
Like Headlight, we were looking for some kind of protective Cover. Objective achieved! It looks great. But I can't deny that it looks a little expensive. And the screw to fix the Logo part, I am not sure if 4 screws are necessary, and the installation method is also a bit tricky as one screw hole is located near the part that fixes the Guard to the body, and the screw is not cut into the Guard, but a separate part of the Nut, so after installing this part on the MotorcycleBody, the fixation of the Logo part was a bit tricky. Therefore, it was a little bit difficult to fix the Logo part to the MotorcycleBody after installing this part. Therefore, I give it a rating of 3. View detail
Fits: HONDA CB250R, HONDA MONKEY125, HONDA CBR250RR, HONDA CB300R
Simple
Simple and unobtrusive, it is suitable for large people.
I wish there were more colors available.
The texture is so-so.
View detail
Fits: HONDA Super Cub 110, HONDA Cross Cub 110, HONDA GB350 S, HONDA MONKEY125, HONDA Super Cub C125, HONDA NC700S, HONDA NC700S Dual Cluth, HONDA NC700X, HONDA GB350, HONDA NC700X TypeLD DCT, HONDA NC700X Dual Cluth, HONDA INTEGRA, HONDA NC700D, HONDA X-ADV, HONDA NM4-02, HONDA NM4-01, HONDA NC750X TypeLD DCT EP, HONDA NC750X TypeLD DCT EP, HONDA NC750X DCT EP, HONDA NC750X DCT EP
Replacement purchased with KITACOOil pump
It has been about 2 months since I installed it, and I replaced it with a KITACOOil pump, so I am not sure of the effect, but I replaced it hoping that it would reduce the resistance of the oil flow.
But with you all, it's expensive anyway.
Therefore, we have set the cospa to 1.
However, I feel that the quality construction is good.
The nameValue in collaboration with MORIWAKI is also a factor in the high price.
I can recommend it, but it would be for those who can tolerate the incidental effects and cosmetic costs.
View detail
Fits: HONDA Super Cub 110, HONDA Cross Cub 110, HONDA GB350 S, HONDA MONKEY125, HONDA Super Cub C125, HONDA NC700S, HONDA NC700S Dual Cluth, HONDA NC700X, HONDA GB350, HONDA NC700X TypeLD DCT, HONDA NC700X Dual Cluth, HONDA INTEGRA, HONDA NC700D, HONDA X-ADV, HONDA NM4-02, HONDA NM4-01, HONDA NC750X TypeLD DCT EP, HONDA NC750X TypeLD DCT EP, HONDA NC750X DCT EP, HONDA NC750X DCT EP
Nice try... I manage to get there, though.
I bought this to put on my ct125 JA65 which is the same model engine as the grom and monkey125. At first glance it looks like it will fit, but the rubber packing is thicker than OEM, so the lid will not close.
We are temporarily replacing it with OEMRubber packing and see how it goes.
View detail
The handlebar paint was easily peeled off, which was unfortunate.
I was very disappointed that the Black paint peeled right off.
I could not believe it was a MORIWAKI product.
The peeled areas were repaired with BlackMagic.
Handlebar height became lower and very enjoyable.
View detail
This is my updated review!
Very nice high quality materials, bad execution. Quality control must be bad at Moriwaki 1. Had this shipped from Japan to the US, cost a lot of money. 2. I received a defective system: the exhaust pipe was cut wrong so the nut on the right side of the engine cannot be tightened even with a short socket due to the curvature of the pipe being so close to the base where it connects to the engine. 3. Then the clearance between the mounting base and the muffler itself is so close that you can't get ratchet in between to tighten the 14mm bolt, you have to get creative and use other tooling.4. DO NOT USE THE RTV SEALANT THEY PROVIDE! It's really bad quality and I used a little in between the connection from the muffler to the exhaust pipe and it made a noxious smell, it doesn't really work for it's intended purpose either, it will not hold the rubber sheets in place, it just makes a mess. Other than that, when I opened the box, I noticed all the materials were packaged very nicely and the finish seemed like very high quality (it's too bad the quality control was bad). As for the sound at idle, it's pretty nice (actually sounds like a motorcycle, rather than a scooter)Once your are accelerating, the sound is reduced highly and is nice and somewhat quiet at higher speeds.If all the issues that I mentioned were cleared away, I would give this exhaust 4 stars, but until it's remedied, Moriwaki gets 3 star for quality control issues for now. View detail
good-looking
It is a MORIWAKI product with no mistakes. I wish there was a pair of Handlebar Post on the receiving side, but … (I have not been able to recognize it, though there might be one). View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE
no problem
I am not satisfied because the upper is MORIWAKI. If possible, I would like to use the same brand. View detail
MORIWAKI Sticker
I haven't put it up yet, but it's perfect for SmallさくOne point.
It is originally to be applied at the bottom half of the carburetor, but it looks good in other places as well.
View detail
Fits: HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS
The color is ….
The price was high and I bought it after much hesitation.
The drip that says Black-like and the color says Black, but …, it is close to the Bronze collar that is common in window sashes.
Well, it is close to the color of the Handlebar Brace I bought a while back, so I'll let it go. I think it was Titanium color, right?
Whoever buys this should never imagine AnodizedBlack.
View detail
It is easy to install. to Racer's look and feel.
Security parts for CBR250RR MC51 for Sports competition (Mirror) I purchased this product for the removal of the
The mirror had been removed and the scratches on it were…not parenthesis looking good, so the purpose was to cover them up.
The effect was perfect and Parenthesis improved.
We have not experienced any problems with price or quality.
Order of installation
Remove the existing Mirror with a .5mm Hex.
Attach this product with a 4mm Hex.
Returning is easy in the reverse order.
It's not tight enough for the Hexagon Bolt to lick.
We feel that Bolt's condition should be closely monitored, assuming that it will be put on and taken off many times.
View detail
Bolt size was wrong, but the quality was high.
I tried to use it on my Panigale, but gave up installing it because it was an M6 instead of an M8.
However, we switched to M6Spec. because of its higher quality compared to the price.
The product was designed with no problems in installation and the texture of Aluminum, and was recommended.
View detail
Windproof effect is low.
I don't feel it is as windproof as I thought it would be.
The only thing that has changed is the appearance.
View detail
Paint peeled off...
Paint has been peeled off.
Paint and surface preparation...zatu, amai?
Satisfied except for the above.
View detail
Position is just right.
CB250R OEM footpeg has Large rattle
(especially Change Pedal)
I replaced it with Rear Sets because it was very cheap.
It is 8BK-MC52 in case you are wondering.
Originally, Position was fine with the OEM.
We chose MORIWAKI products, which do not require so much movement.
Alternative Shaft was used for installation.
I was able to push PivotShaft out by hand without jack-up.
(Jack is shown in the photo, but not loaded.)
I am very happy with the position, but there is one difficulty.
Boots with a slightly elongated sole should have a footpeg and a heel guard.
The Sole is pinched when the Brake pedal is stepped on.
Coupled with footpeg's superb GizaGiza, you will be stuck for a moment.
I was about to stand up and stumble, so I put Heel Guard on.
I made it myself with Aluminum Plate and affixed Carbon Seat.
Also, this can't be helped, but the Brake Side is
The OEMExhaust System's Heat Guard is heeled.
If it had been Babyface, it would have been impossible.
View detail