Reviews
I don't know.
Riding the CB250R, I thought, NORMAL footpeg, when I put my foot down.
The footpeg is just out of the way... sweat.
The CB250R really doesn't have a wide selection of kazutam parts.
And MORIWAKI
The instruction manual says to float the rear tire and pull out the shaft...
Sweat
CBs have a short sidestand that makes them lie down a lot, and when you pull out the Shaft, the Swing Arm shifts.
I had a lot of trouble doing it by myself, and if I wanted to do it by myself, I felt it would be better if I read your friend and we did it together.
I was afraid that the Motorcycle would fall over.
I would have chosen Silver for the Rear Sets because I am concerned about fading, but since the bike is Black this time, I decided to go with Silver.
Black is selected
It's raining today, so I can't ride, but it's nice to get back on the bike.
I would be happy if Shift feeling would change too.
Things are clean and Parenthesis is good.
View detail
It does not correspond to Japanese Vehicle Inspection.
for RaceIt does not correspond to Japanese Vehicle Inspection.
I don't remember there being any regulations for vehicle inspections in FOOTPEG? I was wondering.
Purchased with the understanding that the Manufacturer would just not warrant it anyway due to the disclaimer.
When it came time to install it, I understood what it meant.
The Shift side is fine, but the Brake Side is not.
I cannot add a NORMAL stop-lamp switch.
Therefore, the Stop-lamp does not turn on even if the Rear brake is stepped on.
So what to do about it, I hear it's common in other Rear Sets.
A separate Hydraulic Switch attached to the Brake line will solve the problem.
However, to do so, it is necessary to remove the banjo bolt of the rear brake and bleed the air.
Also, the stop-lamp switch needs to be wired.
The work itself is not that difficult, but it is dangerous for beginners Level, so choose to hire a PRO!
Feels good after installation.
Gear changing also seems to be well determined in a small way.
Position is still a little tight.
The non-slip surface of the footpeg is quite sharp and I don't think it slides at all.
The soles of the shoes feel like they are being scraped off, so be prepared for that to a certain extent.
View detail
Fits well with White body
Since the OEM footpeg is Silver, the impression can be tightened without destroying the color balance.
Pre-assembled, footpeg is set at 23mm for a natural feel and easy adjustment of Stop-lamp lighting.
The overall stability has been improved because it is easier to hold the ankles, although the body is originally designed to have a natural knee grip.
If you are installing it by yourself, you need to use Pliers for Split Pin and Torque Management, and be careful not to forget to tighten them.
The first unit also had the Rear Sets installed, but it was a little more difficult because of the Full Cowl, the Quick Shifter, and the need to remove and insert the Split Pin.
The Instruction Manual is written for people who know what they are doing, so if you don't have the tools and knowledge, you should bring your own tools or buy them from a shop that can install them.
The item is definitely nicely finished and the Pedal's Rubber is solid.
Since there are not so many parts of a motorcycle that can be played with, this is recommended for those who want to create something different from others in areas other than the Handlebar area, Exhaust System, and Fender.
View detail
Changed to Black!
It is a change from Silver to Black. View detail
VTR1000F amazing rearsets
These are top quality rearsets design for superhawk vtr1000f. The finish and detail is the best. Installation was a bit more difficult compared other bikes. But all you need is basic tools and basic skills. The position is a tiny bit more aggressive but still comfortable. The footpegs are much better too. Best investment ever! Love them! View detail
MORIWAKI Step Hold Plate for Rebel1100
The packaging is good and the product coating is excellent I installed it by myself and the manual is also described in detail. Thank you. View detail
cb1100RS 2021
For my uncle, I prefer a Position that is not much different from NORMAL. After all, it will look good. View detail
Foot Refreshing
The footpeg area is easy to hold and comfortable to raise and lower the foot.
It may be no problem if you get used to the OEM system as it is, but it eliminates the possibility of your toes getting caught every time you put your foot on the wrong side of the toe.
Installation takes less than 10 minutes and is highly recommended if you have working knowledge.
Torque management should be done well because of the suspension.
View detail
I didn't want a Foldable Footpeg.
With the OEM Footpeg, the bar moved with it when I shifted my feet, so I replaced it.
Just to be Fixed Type would be nice.
As expected from a famous Brand, it is easy to use and has a good texture.
Heel Guard is solid, which is good for me personally.
View detail
Easy foot position
The thin width allows for easy positioning of the feet.
However, since there are only two screws in the rear, I wonder if there is too much load on the front.
View detail
Reliable Brand
We felt that the OEMHandlebar was too high, so we lowered the Handlebar and made these Rear Sets to match.
The details are well made, and the GEAR goes in comfortably! I was worried that the side stand might interfere with the bike, but I found it easier to pull it out. It looks Sporty and I'm happy with it.
View detail
Great installation accuracy.
I installed this on my 2012 CBR1000RR.
The texture is wonderful. There was no problem with the accuracy of the installation. This footpeg does not have a heel guard on the right side, so I had to use the OEM small heel plate.
The left side is easy to install and ready to use, but the right side is not.
As for the Right Side, it took some time to install because of its complicated structure. However, it was possible to install it without any problems if you follow the instructions in the installation manual.
It also has a brake switch and is a Japanese Vehicle Inspection CorrespondenceSpec.
View detail
![[Rear Sets KitReplacement Parts]Footpeg](https://global.webike-cdn.net/photo/impression/59/5939badc42e9a79f307605c272e1f873L.jpg)
This length
The Footpeg that comes as standard is 90mm long, and I felt difficulty in Step work of the inside foot in Winding.
I was considering using another company's Footpeg, but I was hesitant because of the differences in fixing methods, but then I saw that MORIWAKIOEM had a good one! I bought it immediately.
I'm looking forward to OnSeason now that all my frustrations have been resolved.
It's more like this from the beginning (laughs)
View detail
First-class workmanship!
In fact, when considering replacing the pedal kit, I am more out of dissatisfaction with the texture of the original pedal rather than the position of the pedal. I am 180cm tall and the original pedal position is very comfortable, but the rough workmanship is not satisfactory. I hope to improve its texture and don't want the sitting posture to become too aggressive, so this rear pedal of Senxie became the perfect choice. Compared with the original factory, the sitting posture has not changed much, and the quality of CNC workmanship and surface treatment is excellent! -------------------------------------------------- -------- In fact, when considering the replacement of the pedal kit, I am more due to the dissatisfaction of the original foot, not the position of the foot. My body is 180cm, the original foot is very comfortable , but rough work cannot be satisfactory. I want to improve its texture and don't want the sitting posture to become too radical, so the post-foot pedal of the Sen Association has become a perfect choice. Sitting posture is relatively large, regardless of the quality of CNC's work or surface treatment! View detail
I am satisfied with the price.
The brake pedal needs to be fine-tuned so it took some time. I am very happy with the quality and accuracy of this product. View detail
I bought it because I use MORIWAKI Rear Sets.
I use OEM MORIWAKI Rear Sets, but I added them to improve Stroke and Touch.
Stroke and Touch are stiffer and easier to use than OEM.
Stroke is shorter than OEM, so change lever is heavier. (If you're used to it, you won't mind.)
ReverseChangeSpec. but I use it for positive change. (No problem)
View detail
You can change the Position to suit your needs.
I didn't like OEM footpeg, so I installed MORIWAKI which is safe and reliable.
With my shape, the bottom most front would be enough, but
If you are an aggressive rider, you may find other positions easier to ride.
I think the thing is a solid product.
I am happy with my purchase.
View detail
Okay, but the price
I bought it to reduce weight and increase rigidity.
I chose Titaniumium gold because I have black color, but it's a good choice for me.
It's not Black, as the name suggests (I wish they'd offered Black as well).
Large, bold and padded for a more intrepid appearance.
And best of all, MORIWAKI.
It satisfies the desire to possess.
View detail
Improved rigidity
I believe it is a cool looking product with no flesh on it and it helps to improve the rigidity around the pivot. The color is a little bit of gold, so it might be better to check the original one if you are expecting Black or Gun meta. View detail
Improved rigidity
Properly deboned.
It feels like a combination of lightness and increased rigidity.
Titaniumium gold is a bit more yellowish than the usual titanium color, so it is a good choice for the
If you're concerned about the color, you might want to check in advance.
View detail