Reviews
Fits: HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R
It is definitely better than OEM.
I just took it off and put it back on, and so far it hasn't come loose, but if you're worried about it, you need to get it back on.
It looks good, but the price is too high,
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
OEM Parts can be used without waste
Tail area is now Refreshing and better.
I was very worried about the Fender Eliminator Kit because it is available from many Manufacturers.
We chose this one because the Blinker, License Plate Light, and Loading Hook can be used without wasting OEM Product.
As a result, there was no wiring and the OEM parts were used, so we were satisfied with the result.
It is difficult to understand the work procedures in the Instruction Manual.
I was able to install it by referring to the maintenance handbooks on social networking sites of various senior members.
View detail
Fits: HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R
The discreet Gold has a luxurious feel and MATCHES the car body!
[How is it used?
The Frame Hole Plug for CB1100 is only available in Silver, so there is no Champagne gold color available, and I purchased this Cap to use it.
Was the one you received as per Image?
The quality is as good as the Image and the color is a discreet Gold and MATCH.
Was the installation difficult?
Care must be taken not to damage the frame when removing the NORMAL cap, but it can be installed without tools.
The frame hole is 5mm too large, so a 2mm thick rubber plate is used for this plug.
How was your experience with it?
The understated color is chic and cool.
Although it was diverted from another car model, it looks natural and comfortable.
[Included Parts:were they on?
In addition to the Instruction Manual, a Sticker is included.
[Was there anything that disappointed you?
I am not disappointed in any way, but I would like to see Champagne gold on the same for vehicle, not diverted.
View detail
You don't have to go off-road to get the atmosphere.
I used it on a CT125. All you have to do is remove the Axle Shaft and replace it with the OEM Color on the Disc Side.
The body is fixed to the bracket first, but this part is Torx screwed, so it is difficult without a tool.
The wheel did not fit properly unless the Brake Pads were spread out, but the work was generally completed in about 20 minutes.
The back side has a reinforcing rib and seems to be strong, and there was no interference with the ponting.
I think it is also good that the price is Reasonable under 10,000.
View detail
Fits: HONDA CB250R, HONDA CB250R, HONDA CB125R, HONDA CB125R
Yeah, it's cool.
I really wanted to put a windshield on my bike.
I don't like the large size, so I chose this one.
I was also thinking about KITACO, but I have KITACO's on my Grom.
The product I bought was carbon, but it's also carbon, and the fibers are beautiful.
It's cool.
I don't think it will do much in the way of wind protection, but it will keep bugs and such away from the Meter.
I also had a few options for angles.
But it's a little expensive.
View detail
Parenthesis looking good
I installed the Parenthesis for looks, not for performance or functionality. View detail
Fits: HONDA GROM, HONDA DAX125, HONDA Monkey125, HONDA Monkey125
What special tools are required?
While working according to the Installation Instruction Manual, a special TorqueScrew tightening tool was required, although fortunately a hand-held tool of the same type could be substituted.
I think that a regular commercially available screw would be sufficient for this 4-point screw.
View detail
Heat-resistant Sticker
When I purchased a certain Exhaust System, there was nothing in the Silencer section, so I put it on.
I know it is heat resistant, but is it really heat resistant? I think it's really heat resistant.
But when I looked at it after running, there was no problem at all. As expected of Mr. MORIWAKI.
The durability of the product is unknown as it has just been applied.
View detail
The quality is as expected.
I was a little worried because it was made to order, but the hole position was Exactly and I was able to replace it easily with Hexagonal Wrench1 pc. If you are interested in it, you can buy a Sticker. View detail
Fits: HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R
Dress-up
Frame Hole Plug made by MORIWAKI.
It also comes with a helpful and detailed instruction manual.
There are just a few products listed in HONDAOEM's AttachmentCatalogue.
The quintessence is MORIWAKI!
View detail
MORIWAKIEngineerRing Sticker
Texture is good, a little bit of air is in, but it will come out in a few days. View detail
Fits: HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS, HONDA CB1300SF, HONDA CB1300SB
MORIWAKIFrame Hole Plug
Purchased for CB1300, Silver is almost unnoticeable when replaced from OEM.
If you want to make it stand out, another color is recommended.
The OEM Hole Plug has a groove on the underside.
It can be easily removed by screwing a slotted screwdriveretc. into it.
View detail
It doesn't look like a Seat cover.
good point
The dedicated seat cover I have in mind is an image that is loose in some areas, but this seat cover from MORIWAKI is so tight that it looks like it has been reupholstered.
Even on a 200 km round-trip touring trip, there is not a single wrinkle.
Cushion is also so-so.
Since Motorcycle is Black, Color:I like it MATCH with Gray's Seat.
A bad point
Seat is slippery
I usually ride my motorcycle in Denim pants for motorcycles, and they are slippery, but I don't mind.
However, I'm concerned about the windproof, cold-resistant, rustling Pants for winter because they are quite slippery.
View detail
The colors, ...
Attached to the helmet along with the MORIWAKI muffler.
As you can see from the sixth introductory photo, the color is lighter.
So I put it on a Graphic-colored Helmet and the Graphic became transparent. (Photo:above)
If you are concerned about it, layer it with a single-color Base. (Photo:Bottom)
Good thing it came in a two-pack.
PS:A minor point:the cutline on the outer edge is partially gapped with the text.
View detail
It was unexpectedly Small.
It is better to think of Large Thin Sticker as the main and the rest as extras.
I was going to use something other than Large Seal, but it was too small and I was at a loss as to how to use it.
I ended up using it for the Fork Guard. I think it looks great, but personally, I would have preferred it to be a bit larger.
From a distance, it looks like one point of Red, but it is small and lacks appeal. Well, let's say it's OK.
View detail
Used for Fork Guard
Fork Guard is White and I wanted to paste Sticker, etc.
I think you will feel no discomfort since you are wearing MORIWAKI muffler.
View detail
MORIWAKI's unofficial advertising vehicle.
The Fork Guard I bought off the rack is too White, so I decorated it with Sticker.
There is no discomfort because of the MORIWAKI Exhaust System.
As for durability, well, if it's cheap and lasts that long, it's probably good.
View detail
It looks good
The mounting bracket is a challenge to fit to the bike, but once that's on installation is easy. The airflow is noticably re-directed at an upward angle. The overall build quality is really good. After several months I'm glad to have it View detail
Design-wise good
I checked the video on the web before starting the work. The coupler for the number-plate lighting line cannot be removed unless the cowl behind the seat is removed. It took a little bit of time to remove and install the Carrier Plus, but the installation was completed without any problems. After installation, I found that there is a protective tube on the exposed line from the Number Plate lighting and that there is a gap where it enters the body of the car. It looks more expensive than other products (plate type products). View detail
side cover finish~!
After purchasing the Monkey 125 motorcycle, I installed the Yoshimura Up muffler. After installing the muffler, there were a lot of empty spaces on the car stand, so I bought it to fill that space. There were other brands, but I really liked the Moriwaki lettering, horizontal pattern details, and steel silver material. Moriwaki's brand was also reliable. The price is quite expensive, but if you look at the finish and materials, it makes sense. I'll use it well. Thank you. View detail