Reviews
Fits: HONDA CB650R, HONDA CB650R, HONDA CBR650R, HONDA CBR650R
It is definitely better than OEM.
I just took it off and put it back on, and so far it hasn't come loose, but if you're worried about it, you need to get it back on.
It looks good, but the price is too high,
View detail
Parenthesis looking good
I installed the Parenthesis for looks, not for performance or functionality. View detail
Fits: HONDA GROM, HONDA DAX125, HONDA Monkey125, HONDA Monkey125
What special tools are required?
While working according to the Installation Instruction Manual, a special TorqueScrew tightening tool was required, although fortunately a hand-held tool of the same type could be substituted.
I think that a regular commercially available screw would be sufficient for this 4-point screw.
View detail
The quality is as expected.
I was a little worried because it was made to order, but the hole position was Exactly and I was able to replace it easily with Hexagonal Wrench1 pc. If you are interested in it, you can buy a Sticker. View detail
Fits: HONDA CB1100, HONDA CB1100EX, HONDA CB1100RS, HONDA CB1300SF, HONDA CB1300SB
MORIWAKIFrame Hole Plug
Purchased for CB1300, Silver is almost unnoticeable when replaced from OEM.
If you want to make it stand out, another color is recommended.
The OEM Hole Plug has a groove on the underside.
It can be easily removed by screwing a slotted screwdriveretc. into it.
View detail
It doesn't look like a Seat cover.
good point
The dedicated seat cover I have in mind is an image that is loose in some areas, but this seat cover from MORIWAKI is so tight that it looks like it has been reupholstered.
Even on a 200 km round-trip touring trip, there is not a single wrinkle.
Cushion is also so-so.
Since Motorcycle is Black, Color:I like it MATCH with Gray's Seat.
A bad point
Seat is slippery
I usually ride my motorcycle in Denim pants for motorcycles, and they are slippery, but I don't mind.
However, I'm concerned about the windproof, cold-resistant, rustling Pants for winter because they are quite slippery.
View detail
Design-wise good
I checked the video on the web before starting the work. The coupler for the number-plate lighting line cannot be removed unless the cowl behind the seat is removed. It took a little bit of time to remove and install the Carrier Plus, but the installation was completed without any problems. After installation, I found that there is a protective tube on the exposed line from the Number Plate lighting and that there is a gap where it enters the body of the car. It looks more expensive than other products (plate type products). View detail
If you want to buy another company's product and cry about it later, this is the one you should start with.
Although the price is a bit expensive, it is a well-designed product considering Gold fatigue, etc.
Most of the Fender Eliminator Kits from other manufacturers are simply cut and folded aluminum plates, which are in essence an extension of the License Plate Support Plate. Therefore, if you drive off-road seriously, it will be broken in no time due to the fatigue of gold.
This MORIWAKI product is a product that uses screws to assemble small parts in 3D to prevent gold fatigue. Although the assembly work is time-consuming, it is unlikely that the license plate will break due to gold fatigue and fly off during driving. When assembling, you need to be careful to lock the screws with a product such as Locktite and to protect the thin wire from the License Plate LightLED to the socket. Anyone who can do a little maintenance can do the work.
If you are going to buy a Fender Eliminator Kit from another company, it is safer to buy this one.
View detail
Rather effective wind protection
Purchased Semi-smoke, product is solid and no complaints.
The work itself is not difficult since most of the screws are tightened with screws, but it is troublesome to insert the attached collar, and the instructions are not very clear and a little unfriendly.
Loosening and tightening of M8 screws is difficult with a normal Hexagonal Wrench, and a Short Type Wrench is necessary for secure fastening.
Also, if you put it on yourself, you may be concerned about the mounting angle and the tilt of Both SidesBracket.
After installation, I ran at various speeds up to over 100, and the wind pressure received was clearly different than without.
It may not be as effective as Screen, which is designed to protect against wind, but I found it sufficient for me.
View detail
Easy to install but …
The two-tone color gives a sense of luxury, and if MORIWAKI's custom products are used to unify the products, a sense of unity can be achieved with a subtle tab.
The "Wrinkle" is not reupholstered, so there is a limit to how much it can be pulled, and the SeatCenter will be closer to the Wrinkle. (Is it just me?)
Wrinkle that appears when you get off, so I'll try to adjust again, but be careful if you are worried about Wrinkle!
View detail
Getting down works.
Wind pressure from around 90km/h is unbearable, so it is better to use a dane that does not destroy the original style too much.
After installation, it can withstand about 110 km.
Any more than that and it would be tough without getting down, but in its bare state it was storming even if you got down, so it would be easier by a LARGE amount.
The shape looks like it would be difficult to put on without taking off the light, but with a compact tool, it is large and sturdy even with the light on.
The plating on the included bolt was cheap and I was concerned about seeing it through the gaps, so I replaced it with a BlackStainless bolt.
Note that rust has been floating on the Edge section after a while because the Bracket is steel, and it is quite angular and the paint peels off easily.
View detail
It's hard to take.
Looks Material:Carbon Style is also clear and good.
Just install the Quantity:Pair (for Left and Right) The Bolt holes in the "B" were narrowed back and forth, which I take the liberty of assuming is a vibration countermeasure.
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-4R SE, KAWASAKI ZX-4RR
Why is there no OEM Product?
The Frame hole has been on my mind since I bought the car. I would have been happy if you could have added more color selections if possible… I have installed it with color by myself a little. View detail
Comparison with OEM
Comparison with OEMSeat.
First of all, it looks like Color:The Rebel is Bordeaux, but the overall balance is not affected and it is not visible while driving, so nothing in particular.
The rest of the time, your butt will be quite slippery.
The texture has a slightly wrinkled feel.
MORIWAKI's RedTag is conspicuous. It is hidden while driving.
The fit was quite tight and Large odd.
Cushionability was not particularly effective.
View detail
Moderate wind resistance
I bought this to keep my NAKED style as windproof as possible.
To use ETC [Color] I've got it on Smoke, and it works fine.
I used to use Blast Barrier, but I changed to this product to focus on design.
The Blast Barrier was naturally better in windproofing, and the Blast was comfortable up to about 140km if you leaned forward lightly, but on MORIWAKI, the wind storm blew at about 120km, and it was hard to get down unless you lay down along the tank.
However, it's tough to get down on the ground in a bare state, and it's comfortable for about 100km, so it's effective.
MORIWAKI is much better in terms of texture and fixation, with better texture of Bracket and Bolt, and lighter weight with Aluminum Bracket.
It uses the OEM Meter visor bolt holes to ensure a secure stop.
The instruction manual says to remove the light and fix it to the meter bracket, but if you have a compact tool, you can do it with the light on.
The iron bracket of Blast was heavy and moved back and forth when I touched it because there was no stopper, so MORIWAKI is better in this respect.
The Bracket Fixing Screw on the body side was a cheap Plating Screw, so I replaced it with a BlackStainless one.
The screw is located in a position that cannot be seen at a glance, so it may have been a cost cut, but I replaced it because the silver screw was noticeable when the surrounding area was all black.
View detail
Fits: KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS
Cool。
I bought this because it was a good price, although it doesn't have an Inner TubeCover, and I think FFork is fine if you take care of it often. View detail
That's what MORIWAKI is all about!
It's a little hard to fit, but once you do, you'll be highly satisfied. View detail
It's cute, but it's a pain to install.
[How is it used?
I finally finished installing it and now I'm going to use it.
Was the one you received as per Image?
I thought some assembly would be required, but I didn't imagine it would be all assembled with boards and screws.
Was the installation difficult?
The Instruction Manual is quite simplified, and I managed to assemble it by relying on the floor plan.
The installation was changed from the one that the OEM fixed with Bolt to the Post of the female screw to the form that it fixed with Nut through the collar to Bolt, and this was troublesome.
How was your experience with it?
I'm happy with it because it looks Parenthesis good from the side while the overall length is shortened as expected.
[Included Parts:were they on?
Basically, it contains only what you need.
[Was there anything that disappointed you?
The fact that some parts required a 7mm wrench.
The Cable of the License Plate Light looks quite unreliable.
Rank.
Other items that would be helpful
Opinions and requests to Manufacturer
All of the bolts are Silver, but I thought it would be nice to have them all in Black.
View detail
I'm trying to deal with my ass pain.
It's not cheap, you can buy OEMSeat.
I decided to introduce Gel Zab to prevent ass pain. It is blindfolded with Seat cover because it looks bad.
I've been using it with Gel Zab for about 2 hours.
The Gel zab was designed to be embedded in the seat cover.
I think the build quality is good, although I think it could have been DAYTONA since it is for Gel Zab.
In case you are wondering, the outer skin is synthetic leather and it is slippery.
View detail
Fits: HONDA CB400SUPER BOLDOR, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF
appearance
To One point, installation is just pushing it in by hand. View detail