Reviews
It is casually MORIWAKI.
I was not happy with the snail-like cowl mirror on my CB400SB, and when I replaced it with a handle mirror, I bought a MORIWAKI one to fill the original hole. At first I ordered a cheap one from Amazon.com, but they didn't have the color I wanted, so I decided to go all out and get MORIWAKI anyway with WebikePoint.
It is a rather nondescript cover with a black matte finish, but since it is a MORIWAKIDesign (I don't know much about it and it is not Mania), I decided to go with it. As I have said many times, it is nothing special, but I think it covers the Mirror Hall in a subtle way.
View detail
Fits: HONDA CB1100, HONDA CB1300SF, HONDA CB1300SUPER BOLDOR
Wow that's cool
The Handlebar area is fashionable and Parenthesis is nice. View detail
When running Circuit.
Purchased to cover up the area where Mirror was removed when driving on Circuit.
Good because it looks Refreshing and Race ish.
Mirror removal is easy as you just use Bolt instead of Mirror.
View detail
MORIWAKIEngineerRing TOP BRIDGE [Top Bridge]
[How is it used?
Replaced with NORMAL.
Was the one you received as per Image?
It was just like the picture.
Was the installation difficult?
A Socket to remove the Stem Nut and a Torque wrench are required.
How was your experience with it?
It looks good.
[Included Parts:were they on?
It is about Instruction Manual.
[Was there anything that disappointed you?
When tightened with 103N of the specified Torque, the bar of the Handlebar Lock did not stick into the Top Bridge.
After some trial and error, I found that the handlebar can be locked even when tightened at 103N by using a 2mm thick StemWasher.
Other items that would be helpful
It would be nice to have a 2mm thick StemWasher.
View detail
Re-posting for some reason, a little bit sad MORIWAKIHandlebar
[How is it used?
City & Circuit, the Position is quite good.
Was the one you received as per Image?
As per Image.
Was the installation difficult?
Installation itself is easy. However, the paint will peel off, so be careful when installing.
How was your experience with it?
The position and texture are perfect.
[Included Parts:were they on?
No problem at all.
[Was there anything that disappointed you?
The paint is a little easy to peel off, though it would be better if it is installed with care.
Point and hang of installation
The Plus screw on the OEMBar End is hard. I used an Impact wrench to remove it.
Please be careful not to lick it.
As you can imagine, the LeftRight Switch Box hits both SIDE of the tank exactly when the handlebar is tightened.
Measures will be taken in the future.
View detail
MORIWAKIHandlebar, which was a little bit expensive
[How is it used?
Street & Circuit
Was the one you received as per Image?
Street Image
Was the installation difficult?
It's not difficult, but it's tedious, none the less....
How was your experience with it?
It is considerably better than the STD Handlebar.
Even with such a change in position, I don't get tired, especially in town.
[Included Parts:were they on?
All of them.
[Was there anything that disappointed you?
The paint peels off surprisingly easily. It should be installed with more care.
Point and hang of installation
As you can imagine, the Plus screw at the Normal bar end could not be turned by hand; it was removed with Impact.
[Notes]
This was also as you might imagine, but Switch boxQuantity:Pair (for Left and Right) Both are stiff hits.
Since we also drive on the street, we will consider countermeasures in the future.
View detail
Fits: KAWASAKI Ninja400, KAWASAKI NinjaZX-25R, KAWASAKI ZX-4R SE, KAWASAKI ZX-4RR
Good texture. Sober but elaborate construction, unobtrusive in a good way.
I've decided to remove the Mirror as I have more opportunities to run on Circuit.
I've been looking for a Can Seraar because my aesthetic sense won't allow me to just remove it.
I've seen other Manufacturers with less than stellar reputations and flashy, expensive products.
intermediate between the two. (?) I decided to go with this one.
As a side note, this is my first MORIWAKI product.
I don't have much luck with KAWASAKI.
The black anodized glossy finish is a great way to hold down the claims of the Parts.
The logo is properly included in the proportion of the three, and it also has some three-dimensional modeling.
It is an elaborate construction and I am personally very satisfied with it.
The reaction makes Bolt's head stand out.
So, I made the Plate about 1mm thicker and the outline about 1mm larger.
If you make the Bolt a plate Bolt and make the Plate surface flat, you get 100 points.
The price seems rather high, but it can't be helped.
It's not like it's going to break, it's not going to sell in quantity, and it's going to cost a lot of money to build ... .
It is much cheaper than One-off production.
View detail
Fits: HONDA VTR250, HONDA Monkey125, HONDA CB750, HONDA CB400H-V REVO, HONDA CB400SB, HONDA CB400SF, HONDA DAX125
appearance
It's a place where you can see it. It's self-explanatory… View detail
Great looking *Scraping is nice!
I want to do something with the Handlebar Holder of NORMAL and various things I looked for AfterManufacturer
I bought it because I thought MORIWAKI's was the most beautiful made
It's Cut-Out, so it's very clean
Replacing it won't lead to a performance improvement, but it's a nice improvement in appearance
It's a part that you'll see all the time when you're driving, so it's Large satisfying Parts
View detail