Reviews
It's inexpensive, so it's a good idea to have it as an insurance policy.
I ended up relying on Extractor, so I couldn't use it on the rusty, soggy Screw.
However, it would be good to take it as a preliminary bad idea before drilling holes with Drill.
It is possible to buy it as insurance because of its low price.
View detail
We can't expect too much.
I was attracted by the phrase, "You can turn a tapped screw! I was attracted to this product by the phrase, "You can turn a screw that has been tampered with!
However, in the end, it depends on the strength and condition of the Screw side, so it is not able to stand up to a soggy Screw.
It's a pain to use Extractor out of the blue, but it's good to have it as an insurance policy for positions and types of Screws where Neji-saurus-like things are not available.
View detail
Compact
Compact and useful for use in tight spaces.
It is small and cannot apply much force, but it is easy to use when tightening a little and replacing the tip.
I like that the price is not that high.
View detail
Driver shape for easy turning
Because of the shape of the driver, Torque cannot be applied, but it can be quickly removed by holding the shaft and turning it.
I had the opportunity to use it at work and found it very easy to use and purchased it as a tool for Motorcycle maintenance.
View detail
Small and comfortable to hold
The Size is easy to grip.
It is also easy to apply force there.
View detail
Rather than turning Screw.
Purchased because I wanted a Minus in Small size.
Minus of such a size is often used for doing things by sticking it into a gap rather than as a driver when servicing.
View detail
I should have bought Koch from the beginning (#2)
Common L-shaped Quantities:I had been using a set, but I happened to know at work that there was a Driver type Hexagonal Wrench, so I bought a 5mm one of the same series.
The L-shaped type cannot be used to work around electrical components with complicated wiring, which can cause licking of screws and damage to the wiring.
But with this driver type, all these problems were solved in one shot.
The Large size of the pattern is also different from 5mm and is thinner.
View detail
I should have bought this one from the beginning.
Common L-shaped Quantities:I had been using a set, but I happened to know at work that there was a Driver type Hexagonal Wrench, so I bought a 4mm one of the same series.
It is extremely easy to use and almost eliminates the risk of dropping tools and damaging the motorcycle.
View detail
Inexpensive, but normally usable.
It's cheap Level sold at a hundred and one. I bought it imagining that it would be a "good" product, but I was betrayed, but in a good way!
I use it not only for Motorcycle but also for maintenance of Glasses and Watches!
View detail
honestly speaking, it's subtle
I thought it was easy to use with Pencil type and purchased it for electric inspection, but the system is not very good. View detail
Accuracy and strength!
Of course, as Precision Driver, the precision and strength of the tip is outstanding.
When I made Slit machining Spark plugs for Others, I also use Precision Driver for pushing and drilling holes to get BALI when I am about to Penetrating in Slit machining.
Really great tip strength!
View detail
It's easy to use!
I have been using Driver by VetCell, but it started to lick somehow, so I bought this guy I saw on Youtube.
I removed the screws from the CB400SF Blinker. It's like I'm chewing something solid." I am satisfied with the
The Grip also has a strange, easy-to-grip feel, like Rubber-like resin.
I thought I'd get a few other Sizes in the pipeline!
View detail
Convenient to have
Accuracy is not bad and Quantity:Easy-to-use Driver with 1 Set of 6pcs.
Key less This quantity is always needed for key battery replacement, etc.:It is safe to say that Set.
It can also be used to unlock Wiring from Coupler.
View detail
It comes in handy for details.
Effective for use in tight spaces where there are no gaps.
It is easy to turn and Torque can be applied so that it will not be licked.
Compact, so it's handy to have one in your toolbox.
View detail
safety
Safe and easy to find the power source. When searching for a permanent power source from the vehicle's harness, the LEDs on the body light up to make it easy to locate. View detail
It's for electricians, but Tough
This kind of standard is for VESSEL electric (Many manufacturers are copying it as it is) I think, but after using both, my honest impression is that it's hard to choose between the two. I prefer this one.
The grip with the groove of Beth Cell Type might be a little better to grip with an oil hand, but this one which looks smooth also has a texturing pattern and unexpectedly does not slide so much.
The grip is triangular, so it's easy to turn quickly, and if you need more power, the hexagonal driver shaft allows you to use a tool to turn it.
Heads with Plus notation are Material:Although it is plastic, it is quite sturdy, and although it is necessary to take it easy compared with Penetrating Driver, it is possible to use it enough even if you beat it. PlusMark of the identification doesn't disappear easily either.
If you want to use one to handle everything from fast turning to tooling up and turning with LargeTorque, this is the one for you.
View detail
Very short driver
First for carburetor adjustment (Minus) I bought it because I thought it was convenient for
The overall length of the screwdriver is shorter than that of a standard Stubby Screwdriver, so it is the only choice for tight spaces.
Also, the Clip of Cowl on the underside of the car body (Plus head) You can apply it straight without worrying about the clearance with the ground when you remove the
By the way, Minus side can be used conveniently when prying Clip which is hard to come off.
This small size allows you to use it interchangeably, so you can have both Plus and Minus, and it fits in your toolbox compactly.
View detail
"Normal The sense of security of
It's a very ordinary Driver.
However, unlike very cheap products, there is a sense of security that can be taken for granted without any modification.
Shank and Grip are solid, Plating is clean, and durable. I've been using it quite roughly, but there are no cracks or chips in the grip or the tool tip. The tip is worn out.
If you are not a fan of the thicker grip end for fast turning, this one may be easier to turn.
It's not like a hundred-yen tool or a BALI, but the tool tip has a little edge, so if you use it roughly, it might scratch the object.
View detail
In OHLINSFork's Setting
[How is it used?
I bought this for the OEM Front fork damping adjustment from RSV4 FACTORY.
How was your experience with it?
I used to use the Wrench from Hexagonal Wrench Set, but it was difficult to use.
At that time, I saw other people's impressions and thought it looked easy to use, so I bought it.
Since it is a Driver type, it can be turned lightly.
[Points to note]
Since it is a ball type, you can approach from many angles, but if you apply too much torque, the ball will come off.
Also, I wanted this size for suspension setting, but I bought other size by mistake before, so please look at the size carefully when you buy!
View detail
You can find the power source safely.
This Inspection Tester is indispensable for the installation of electrical components. It is useful to find the permanent power supply or attachment power supply from the harness of the vehicle. If there is a power supply, the LED on the body will light up, so you can find it easily. View detail