Reviews
Expected heat resistance
The power supply wiring needs to be passed through the side of the engine, and to protect the wiring from heat, this product was placed over the 5ΦColgate Tube because it has higher heat resistance than the ordinary Colgate Tube. When you put the wiring through the Colgate Tube, you can easily put the wiring through the Colgate Tube by squeezing the Tube as described in the Instruction Manual.
The Tube is elastic and fits perfectly to the thickness of the Wiring you pass through, so it looks neat.
After cutting the Tube, it will fray, but this will not be a problem if you fry it with a lighter when you cut it.
I gave it a 4 because of the somewhat high price.
View detail
That would be handy
Bracket used to stop Wiring, 1Quantity:Set contains 8 pieces.
I often use it for in-house Wiring of cars and I also use it for Motorcycle as you can see in the picture.
Thin Wiring is fine, but thick Wiring is not very suitable.
The clasp is made of soft gold, but this means that it is easy to open, and if you hold Wiring from below, it will eventually loosen.
If the Bracket is placed in a direction that does not require any force to open it, there should be no problem.
The adhesion of the double-sided tape is neither good nor bad.
If you apply it with a good surface preparation, it will hold up reasonably well.
It is a useful tool that is easy to use.
View detail
DriveRecorder - A must-have for installation
I used it to install a DriveRecorder in my car.
I have installed several DriveRecorder units in the past, but most of them were powered by Cigar lighter sockets.
I was worried about whether it was just taking 12V, or whether it was bucking the voltage, etc. So I thought, why not just add a Cigar lighter itself and take it from there?
One of the most exciting things about this product is that it comes with three take-out Fuses. (I will use one of them).
The FuseCase is equipped with a normal flat type, a low profile type, and a MINI flat type, so if you want to make a branch wiring from the Fuse box, you can turn it from other types of wiring. (However, since the end of the branch wiring is attached to the Pipe Type Fuse, it is necessary to prepare the Fuse, FuseCase, and wiring for the end of the Fuse, or to cut the Fuse Gold and make it into a Bullet Terminal. (In this case, if the polarity of the fuse is wrong, the wiring will be directly connected without fuse.)
It is not waterproof construction, so care should be taken when using it for Motorcycle.
View detail
Easy to use
I have never bought a double cord before, but this time I bought it to install a DriveRecorder in my car. 6 meters were left over and I was going to keep them for motorcycle use, but I had to install them in two cars in a hurry, so I ended up using all of them.
0.75 is the thickness of the wiring cord I often use, and the same 0.75 single is used for playing with the electrical components of my motorcycle. I have never had any durability problems with Emon's Wiring Cords, and I feel that I can use them with confidence. I am going to redo the wiring of my Motorcycle DriveRecorder, etc., so I am thinking of using a double cord to make it reflect. I will buy and use this Wiring Cord again.
View detail
Necessities
It's a necessity to check the energized side. This time, I checked the energized side to get power from Fuse. The energized side is indicated by a red Lamp. Since you can't see the electrical connection, it is useful if you have one of these. I am satisfied with its good cost performance. View detail
I'm glad I got the Large size.
I purchased the 8L size thinking that it would be too large for my VTR250, which can only drain about 2L of oil, but when I used it, I found that it was surprisingly easy to dump oil (it does not spill even if you shake it when you hold it), so I was right.
Note that the vehicle body is in Maintenance Stand with the Rear raised; if it is left in Side Stand, it will not be high enough.
View detail
In the Filter of Rokdabo.
[How is it used?
Used to replace Oil Filter in late cbr600rr pc40
Was the one you received as per Image?
As shown in the Image. It worked normally.
How was your experience with it?
The position of the Filter on the Rokudabo was difficult to work with, but it did its job well as a Filter wrench.
[Points to note]
The direction of rotation can only be in one line.
View detail
standard equipment
[How is it used?
Used when changing oil in cars and motorcycles.
How was your experience with it?
Since they are disposable, they are convenient and require no further maintenance.
The paper is firm, so there is no worry about Oil spillage.
Cost performance is good and I have been using it for a long time.
How did it compare to other products?
Material:Unlike Plastic, it is easy and maintenance-free.
View detail
Not sticky and easy to use
[Purchased for.
I replaced the Blinker with an Other Brand Product, but the wiring was more exposed than I expected, and although I think the product is Large and sturdy, it looked ugly, so I bought it for protection and to fix the appearance.
Impressions of use
While the Vinyl Tape on the market is sticky and not heat resistant, this one is not sticky and sticks to Beauty without stickiness, and it is also heat resistant, so it is perfect for wrapping Motorcycle wires and such!
It was very easy to work with because it was not sticky and I could take it off and rewind it again if I felt I had made a mistake.
Thanks to Wiring, we were able to hide and protect it very nicely, so if you are in the same situation, please give it a try!
【Review】
Cosy, no complaints!
Wiring is now clean!
View detail
Cheap and normal use.
[How is it used?
Oil replacement of ninja400 (1.6-2.0L) For cleaning of OthersParts.
Was the one you received as per Image?
It arrived in Beauty condition.
How was your experience with it?
It is not very thick, so it can easily be placed under the car body.
The size is not too large, and I think 2L is just right. 4L replacement would be too much, so I think a larger size would be easier to work with.
There is an oil sink, but it is not very easy to use, and there were some common oil spills.
I have no complaints because it is inexpensive and Compact.
How did it compare to other products?
I think this product is fine for DIYLevel because a cheap oil tray is sufficient for this purpose.
View detail
Disposable and easy to use
It is inexpensive and disposable, so it is super easy to use. (I don't know if I used it wrong (with paper), but the oil I poured leaked out from the folded part.
It was easy to use, but I have to give it a few less stars because of the Oil leakage.
If you change Oil frequently, you may want to buy a funnel after all. (Cosmetically)
However, it is a RECOMMENDATION for those who are attracted by the ease of use and the fact that it can be thrown away as is after use.
View detail
Surprisingly Compact
I have not used it for Oil replacement yet, but it is surprisingly Compact and will be useful for Oil replacement. View detail
25mm
When wrapping tape around a long wiring, it can be wound faster than the commonly used 19mm. It is also easier to work with because the glue is less sticky. The disadvantage is that it is expensive. View detail
Wiring only
Compared to Vinyl Tape of the same size, the price is more than five times higher, so it is not cosmetically pleasing; still, I use it partially because it is not sticky afterwards. View detail
Various applications
It can be used for a variety of purposes.
Fixing of Speaker in Helmet, fixing of small objects around MotorcycleHandlebar, fixing of ETCBody
Fixing Offhel and Goggles Anyway, it can be anything.
View detail
It is used for DIY of the stationary portion of the single seat cover of Ninja250R. Although the thing of plating of the company was used, since it had been divided in vibration, the tougher stainless was chosen. Reinforcement, distortion-proof, a
It is used for DIY of the stationary portion of the single seat cover of Ninja250R.
Although the thing of plating of the company was used, since it had been divided in vibration, the tougher stainless was chosen.
Reinforcement, distortion-proof, and rust-proof are the honor students unique to a stainless, and are high. [ of cost performance ]
Since the hole is made, as soon as it processes it with a bolt, it can treat freely.
While it is hard, what processing is hard to carry out is unavoidable.
View detail
Serves the purpose well.
Size and capacity are perfect for kei car and a big scooter oil change. View detail
Convenient to have
I bought this because the Cowl claw on my CT125 is hard.
It is very different without it.
I was able to remove the hard nails without breaking them.
View detail
Heat resistant and easy to use!
We used it for Joint protection of SensorWiring near the Engine, where normal Vinyl Tape would melt due to heat.
It is not sticky like regular Vinyl Tape and is smooth and easy to use.
I didn't know this product existed until now, but now it is really useful.
View detail
Useful for tying Harness
Wiring can be neatly bundled by pulling and curling it a little.
It is easy to use as it can be easily cut by hand.
The adhesive is firm, so it does not come off and is not sticky in comparison.
View detail