Reviews
Amon relay it's good
This is 12 volt relay. This time I am using in controlin on/off the subwoofer in car. I am worry about electronic switching power supply keep it standby. Because of that avoiding the drain power using this relay.load 12v/8A continue.no more heat . there is no flyback diode.it came with bullet connector. View detail
Amon terminal set . useful
It's really helpful what are the basic item need for specially who doing DIY projects in automobile.Items quality good and along with tidy box . reconditioned . Thank you. View detail
Amon Male female character connector
Super quality and good price .even can use 0.5-2mm cables without braking crimping mouth.iron material also strong.highly recommended.thaks View detail
LED.
It's a must-have when using LEDs. View detail
For Power Distribution Wiring
It is a purchase together with Connector to do Wiring for power distribution.
I didn't need that much length, but I had no choice.
It was also sold in the nearby Shop, but the price was a little higher here, so it was a hassle to buy it together.
View detail
For Wiring
I bought this with the Connector for Wiring distribution.
I didn't need that much length, but I had no choice.
Wiring is a purchase of Red to identify.
It was also sold in the nearby Shop, but the price was a little higher here, so it was a hassle to buy it together.
View detail
For OEM diversion
In order to use the Yamaha OEM thin switch, I was planning to use the Coupler from the original Kawasaki OEM switch. However, the Throttle of the zx6r that I was going to use at the same time was difficult to install, and there was a possibility of putting it back together. I wanted to make it the same color as the Kawasaki Coupler, but I had no choice.
The Harness that connects to the Switch has the same 110 type 6-pole Coupler Male as this product, and the YamahaOEMSwitch also has the same 6-pole Male, so it was necessary to replace the Coupler. I checked the wiring of each switch and the wiring diagram of the zrx1100, and inserted the 6 wires into the female position of this product. Because the type is the same, it is possible to connect it exactly, and there was no problem at all functionally. I'm very happy with the way the Switch works.
View detail
BachaoRelay's companion
I've installed these on every Motorcycle I've ever owned.
This is the standard Relay for use with Bach Direct Relay.
I'm sure you can find as many ways of Wiring as you want if you search for BadDirectRelay.
HDLight (Low beam) If you replace the fuse with a power supply extraction fuse and connect this product, you can complete a direct relay without damaging the harness of the car body.
Because there is also capacity there, it plays an active part Large as Attachment power supply.
By the way, in the case of branching, One-touchConnector of WAGO Japan is small and the connection is easy, and is recommended.
If you search for "WAGO Japan" on Amaz◯n, you can buy the exact same one at the original price.
Both this product and the One-touchConnector above are non-waterproof, so be careful where you install them.
Nowadays, it is almost necessary to install USB power supply and other electrical components, so we are very grateful for the parts that can be used to build a direct relay at a low price like this product.
View detail
Easy to use
[How is it used?
I usually use it for additional Wiring etc., but I bought it again because the one on hand was lost.
Basically I use 0.75sq, but this time it was the WiringRepair of Small TypeMotorcycle which does not use power so much, and addition, so I chose the thin wire 0.5sq here.
[Was the product you received as Image?
Photo
The length is 5m and quite a lot for cheap, so it's enough for Sunday mechanic.
How was your experience with it?
It's just a normal thin wire Wiring Cord.
Even though it is a fine wire, it has a certain diameter, so it is not difficult to crimp.
The good thing about Emon's Wiring Cord is that you can hook up the excess wire on the Holder.
It's nice to be able to keep all the extra lines together, since you basically have to keep them unless you need them.
【Review】
It's inexpensive, easy to use, and convenient for keeping all your Wiring together.
I've always used Emon's Wiring because I've heard that it has no problem with heat and oil resistance.
View detail
Ideal for controlling Blinker current sharing when adding a low-cost Hazard kit.
[How is it used?
When you light a blinker lamp by adding an inexpensive retrofit Hazard Function Blinker relay without changing to the with Hazard Function Blinker relay, you can use 4 of these diodes (2Pack) to control the current sharing when each blinker relay is turned on. I use 4 of these diodes (2Pack).
Was the installation difficult?
Both ends of the wire are cut off, so I used Bullet Terminal crimp terminals this time.
If you don't have a Crimp Tool or terminals, you will need to connect it with a Solderer.
How was your experience with it?
There is no current crossover and they will not fault each other's Relay.
[Included Parts:were they on?
None
You will have to provide all the tools and terminals yourself.
The capacity is 6A, so it can be used in most current paths.
View detail
A must have Hazard addition to your Handlebar Switch.
I bought this to put the NC700X OEMHandlebar Switch on my Grom JC92.
By using the NC700's Handlebar Switch, the Hazard and Passing functions can be added.
I used the teachings of our predecessors that you have published on the Net as a reference for my Wiring.
Thank you, my predecessors.
The purpose is to prevent backflow into the Hazard circuit when the Blinker is activated.
Quantity:Pair (for Left and Right) Quantity to bite, BlinkerWiring:2pc. Set is required, so Quantity:1 Set of 2pcs.Pack will be very helpful.
The wire is connected by soldering, and the connection part is protected by the expansion tube.
The Diode itself comes with a Protective Tube from the start.
A SORD and Ka SORD are very easy to recognize by the color of Wiring. (It is one way from White to Ash)
Thanks to you, we were able to add the Hazard function to Smooth.
Very satisfied
View detail
You could almost say it's a classic!
I use it as a Relay to turn the 12V on and off with ACC power.
It's working fine.
It's a classic
View detail
For Wiring Processing
I'm sure you can get it anywhere, but I bought it for the free shipping. View detail
Simple functions
It is the switch of the simple function of only On and Off that omits an extra function. It is a switch that is easy to handle by DIY because the circuit is simple because it is only the switching function of the On and Off of the electric equipment. The appearance is also very simple. View detail
It helps in times of need.
It is very useful to have one in your tool box for installation of electrical components, and it is convenient to extend the wiring and free the installation location of the body of the electrical components. View detail
watchman
I have been using Emon products for a long time, not only for Relay, but also for Motorcycle. I think the only point to pay attention to is the waterproof measure. View detail
Separate the burned 2-pole Coupler into 1 pole each!
Is it possible to burn the Coupler of Yamaha, especially DynamoWiring of FZr1000... I divided 2 poles into 1 pole each with this product as shown in the picture.
Now there will be no leakage and no Short.
So far, it has not burned out, even with a single pole Coupler.
Emon is still Emon! (Mystery)
* The video is my car introduction
View detail
very useful
My car is KAWASAKI’s NINJA 400, model year 2019. In order to connect the turn signal, I bought this product from AMON. It should be noted that it is not waterproof, and it is completely fine to put it under the rear seat. It has been used for more than 1 year without any failure. ---------------------------------------------- My car is 400 , the 2019 models of KAWASAKI NINJA. After receiving the order to turn lights, AMON buy this product. It should be noted that it is not waterproof, and put him in the rear seat following no problems. Spent more than a year have not been any failures. Powered by Google Translator View detail
It is convenient for installation of electrical components.
It's very convenient. View detail
I used it for Horn Bracket.
I needed a bracket to move the position of the horn, so I used it. It has a solid thickness and is made of stainless steel, so it seems to be resistant to Rust. View detail