Reviews
I love it.
The Large is very good and I use it for Oil change trips.
There is no problem in particular, but if I may be so bold, it would be helpful if the paper could be folded easily.
View detail
Let's use it for Oil exchange!
When replacing oil, it is easy to fail to catch the oil if the waste oil is thrown away, but with this, it is safe.
There is no such thing as a failure and overflow.
It makes a difference whether you have this or not, and you can replace the oil with confidence!
View detail
It looks like it will fit in the stated capacity.
2.The product is up to 5L, but it seemed like a Limit at about 2.3L.
It's in there with no problem, so it's supposed to be in there as described.
It's much easier to dispose of than the previous Dan Ball box was.
View detail
It was just like the image.
I have just purchased a DDR−S100 with KAMUI3 for the purpose of fixing the Wiring to operate it as a HelmetCamera.
My DDR−S100 was modified to be able to cut the cord in the middle and connect it with Waterproof Coupler after the USB cord was disconnected. The third image shows the Helmet side. By connecting the other side of the cord connected to the Mobile Battery to this side, the cord does not get in the way when attaching and detaching the Helmet.
This time, when I use KAMUI3 for motorcycle commuting, I thought it would be better to have a DriveRecorder, so I decided to install DR−S100 on my helmet, and selected this product as just the right one to fix the Power Cord.
This 3mm TubeHolder was not bad looking and had just the right diameter to move it a bit against the thickness of the Wiring.
I have used 5mm diameter ones in the past, but they can also be cut and used, and I think they are quite user-friendly Parts. However, the adhesive strength is not very strong, so you need to be careful where you apply it. If it comes off, I will reapply with a stronger double-sided tape.
View detail
Purchased oilfor replacement for ninja1000
Items necessary when changing oil.
It can be disposed of as combustible trash as it is.
I think I will continue to Repeat Emon because other Manufacturers are expensive.
The only drawback is that the Oil will ooze out and if you don't double wrap the Vinyl and dump it, the rest will look Large weird.
View detail
Useful for Wiring protection and concealment
Useful for concealing and summarizing Wiring
Bend it about 45 degrees toward the uncracked side to open it up and put it in.
It is recommended to install it near moving parts or near the heat source.
This time, I protected the Cable on the front of Camera in DriveRecorder!
View detail
Useful for Wiring protection and concealment
For fine lines, φ3mm is sufficient
Only one Plus wire (ACC power etc.) so it is ideal for protection!
View detail
Service Reminder Reset for New Model GSX1300R HAYABUSA
[How is it used?
Recently, many manufacturers have adopted a system in which the Lamp on the Meter lights up when it is time for maintenance.
Various foreign car manufacturers, especially Ducati, are doing this.
But recently, domestic cars are also becoming like that:you have to drop Gold to the Dealer to get rid of the Lamp. Is this part of the Dealer's business strategy? So, even for a simple oil change, if you don't go to the Dealer to have it done, the maintenance Lamp is still glowing all the time.
is Japanese pampas grass, a simple homemade one is all that is needed to solve the problem.
Was the one you received as per Image?
As per Image
It's better to buy it with other things. Since it's only about $100 anyway, the actual store is a better deal when shipping is included.
How was your experience with it?
Effective.
[Points to note]
You have to insert it deep to get it to work.
How did it compare to other products?
Nothing in particular to compare.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
In doing the work, this method is probably a maintenance procedure that is not covered under warranty.
If you want to be stingy with your Gold, please use it only as a reference.
If you are a little worried about the work, you should still buy the OEMReset switch.
OEM reminder Reset switch
09930-83130 Available at Webike, but currently out of stock?
By the way, in most cases, they fail.
It will not respond unless it is inserted firmly and deeply.
Then press and hold the LeftSelectSwitch▼Button to open MENU, select SERVICE, MODESwitch to determine RESET, which is not usually displayed, select Yes when Yes/No appears, and then you can set it individually!
View detail
Large capacity
[How is it used?
Bullet Type Terminals are required for USB power supply and other wiring processes, but of course Bullet Type Terminals are used up.
Quantity:I bought a set of 30pcs. or something like that, but I found that I had no Bullet Type Terminal on hand and had to stop working on it, so I bought Quantity:1 Set of 100pcs.
How was your experience with it?
It is an ordinary Bullet Type Terminal made by Emon, which can be easily obtained at Home center.
100pcsQuantity:Set is not readily available around there, so I purchased it on Webike.
How did it compare to other products?
No specific comparisons were made.
[Points to note]
Sleeve for waterproof is not included, so you need to prepare it separately if necessary.
【Review】
The Large capacity is recommended for those who do a fair amount of DIY Wiring work.
It is better to store them in a 100x box because they may be lost if left in the bag.
View detail
For ServiceReset
Recent SEA BASS cars have a sign in the meter reminding the driver to change the oil.
I thought the only way to erase it was to have it reset at the shop, but it was easy even for an individual.
The connector hole was too small and the needle gold was too thick to fit in the connector, so I used Emon terminals.
OEMs sell specialized products, but they are expensive, so this was sufficient.
View detail
Wiring branch connections are easy and good.
The differences in Cable size and current capacity are easy to recognize depending on the color.
Note that the Cover is divided between the main line side and the branch line side.
*Because the blade directly bites into the sheath for connection, use in locations with a lot of vibration may result in disconnection or poor contact.
*Care should be taken not to reuse the area once used.
It is easier said than done, since the connection can be made with just one pliers....
View detail
Female terminal Cover Only
This is a Female terminal Cover Only product. A separate Female or Male terminal (Male terminal Cover) is required.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product requires Cover and Male terminals as it is Female terminal only.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Female terminal is recommended to be used on the + (Plus) side since the connection will be covered when the Cover is attached.
View detail
Reduction in cost with Large volume purchases
Bullet Terminal required for power supply connection for cars and motorcycles.
It is safer to buy more than the required number of units in case of failure.
It is hard to pull out easily when firmly connected, so when pulling it out, grasp the terminal part firmly with a radio pliers or the like.
This product is Male terminal only, so Cover and Female terminals are required.
If you are only going to use a few of them, it is better to buy Bullet Type Terminal Set.
I have never purchased anything other than Emon, so I don't know for sure, but it is best to purchase Male and Female terminals from the same manufacturer.
The Male terminal is best used on the ”-(Minus) side because the connection part is exposed even if a Cover is attached.
View detail
Required for Wiring processing
Required Items for connecting Bullet Type Terminal in Wiring
It's priced right, but I think it's necessary and sufficient.
I think it's better to lubricate it because it's not moving well.
View detail
Male terminal Cover Only
This is a Male terminal Cover Only product. Male and Female terminals (Female terminal Cover) are required separately.
Since it is not waterproof, we recommend the purchase of a Waterproof Terminal Set if the connection is to be exposed.
Motorcycle and car Waterproof is rarely seen only in Connector, so I don't think it will be a problem, but it is a good idea to buy it according to your needs.
It is better to have it in Large quantity so that it does not roll around somewhere and disappear because it is a Small item.
Contact between terminals and frames may cause damage to electronic equipment or, in the worst case, cause a fire.
View detail
Used to extend BlinkerWiring
Used to extend the Right Side wiring as it was too short when replacing the Rear blinker.
Naturally, we were able to extend it without difficulty.
View detail
Ideal for Repair
I purchased this product to refresh a MotorcycleParts terminal cover that was given to me by a friend because it was yellowish and deteriorated. I recommend periodic replacement of the cover because many people use the cover for many years without replacing it, causing it to become damaged and short! View detail
Emon Terminal cover
The cover is quite large for a terminal cover for motorcycles, and if it is for a large type of car, I would have liked to see a description to that effect. View detail
1pc. is useful for various purposes
[How is it used?
I bought it to use as a Drain pan for Oil change.
Oil replacement
Chain cleaning
Parts and tool storage for replacement of OthersParts
It is used for
Was the one you received as per Image?
I thought it was smaller than I expected, but considering that I was going to put it under the belly of the Panigale, 5LiterSize was just right in terms of Clearance.
How was your experience with it?
Oil replacement
In the case of Panigale, it produces about 3.5 liters of waste oil, but the weight of the oil causes it to deflect quite a bit.
There is a scale, but it cannot be used as a scale because there is only a line in one place.
Chain cleaning
I also use it as a receptacle for chain cleaner during chain cleaning. the size is just right and the area around it is now dirt free.
Parts and tool storage
When replacing or removing parts, it is easy to keep bolt nuts, etc. in the box and organize them without losing them.
[Points to note]
Material:It's not like a Stainless Steel pan or something, so I think it might deflect and spill if poured in parallel.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail