Reviews
CBR1000RR-R uses this
The Rear Axle Nut of the CBR1000RR-R is 36mm in diameter.
The tightening torque is also high, and a box with many angles was used, but it seemed to come off, so we changed to a 36mm hexagonal box.
At the same time, I also purchased a pure STD Nut with it. I think I was able to buy peace of mind at a reasonable price with FirmlyFit. I think I was able to take countermeasures before I got injured, although I am satisfied with myself.
View detail
This eliminates the need to search for tools.
Rose and kept it in my toolbox. Separate from the tools for my main job,
It is stored in the Motorcycle garage. I use it by hooking it to the Neodymium Hook as shown in the picture, considering that it is easy to understand and within easy reach.
View detail
Is the length of the short method better?
I tried to make a 15-socket holder, but I didn't think about the length of the holder. I didn't think about the length of the holder, because it was about 30cm long, so I couldn't fit it in my tool box. 10-socket holders are available in the Quantity:2pc. I should have bought Set. But
It is definitely better than the Gold genus because it is made of plastic.
View detail
Poor mechanics buy toolsRose
9.The 5 tools were added in the Grip set since the number of tools has increased since the Rose purchase. The work is easy Plus No.2 Driver.
Only 1 pc.
View detail
Exhaust flange, etc.
It is used to remove the exhaust pipe or when the bolt nut is difficult to access due to obstructions, etc.
This is a useful item because there are times when it is not necessary to remove obstacles.
The texture is like KTC!
View detail
Stable KTC
I chose KTC in part because of KTC.
I have been using SIGNET tools for a long time, but I also like KTC as a Brand with stable quality.
Since it is a tool, a reliable Brand is good for mental stability.
View detail
KTC after all
This is for the Axle Nut of the Rear. I bought this hexagonal one instead of the 12-square one because the torque is applied to a certain extent, and the price is cheap and KTC quality is reliable.
For practical purposes, this is.
View detail
Resin Holder for easy insertion and removal of Socket
This Material is definitely better than Gold:PlasticHolder is easy to use.
Material:The Piece of Plastic Holder is stuck on two Gold rods, and the Material such as Shibuichi, 3/8, 1/2, etc.:It can be used to replace PlasticHolderPiece.
Gold genus products tend to loosen and ruin rather quickly once you start using them. This Holder is easy to insert and remove, and I definitely recommend it.
View detail
"Japan" It's a one-of-a-kind Tools Set!
I think it is a tool set for personal level and can be used not only for motorcycle but also for bicycle maintenance.
Except for heavy maintenance, this one (and a few more) will do the job.
The quality is unquestionable, just like in Japan! I think you will not lose anything by buying it!
View detail
When double nut is not available.
I bought this to pull out the sprocket bolt on my SR400.
The reason why we went to the trouble of purchasing the hub clutch is because the SR400 hub clutch has a convex shape for CenterRinging the Sprocket.
This is because the distance between the convex part and the stud bolt is so close that a double nut cannot be used.
I was wondering if I would have any luck using the OEM Nut since it is so thin. Unfortunately, the second one bites only one pile and cannot hang Torque properly.
I had no choice but to buy a special tool.
Still, it was a bit odd to remove the screws because they were coated with screw locks and mine were very sticky.
Fortunately, since it was a RoseRose, access was possible from the back, so I was able to finally remove it by searing it with a raspene, drilling a hole in the center, and pulling out the Torque.
The structure of the Stud bolt remover consists of three Pieces that move and hold the Bolt when it is rotated.
The structure was like a Cell starterClutch.
The screw threads are held in place by the three pieces of the bolt, either on the face of the screw threads or by a line perpendicular to the screw threads, so the screw threads are crushed. Basically, the removed stud bolt cannot be reused.
Since it is possible to engage the stud bolt in the reverse rotation direction, it is possible to loosen the Opposite Thread Screw or tighten the Normal Thread Screw, but as mentioned earlier, the screw threads will be crushed, so it will be a very special application when used for tightening.
It can be used for round bars as well, since it does not need to be screwed structurally.
Maybe it would be good for a sticking Knock Pin or something.
I purchased For M8 this time, so I can use it for Big bike's Exhaust System and so on.
If you have For M6, I think you will have no problem with most large stud bolts.
View detail
The Socket that never misses
First of all, you can't go wrong with a Socket, and I think KTC is just right for motorcycle tinkering. It is a good product with accuracy and strength. View detail
The Larger the Size, the better the accuracy!
I buy KTC for large sized sockets. The price is cheap and the accuracy is good, so it helps me a lot. View detail
Strong!
I don't use Joint very often, but it is a product I worry about if I don't have it.
It is a product of strength, precision and no mistake.
View detail
Adapter with precision!
Adapter of KTC [1/2→3/8] is accurate and just right to pull out and insert. I can use it for years and it is durable. View detail
Precision Adapter
Adapter of KTC [3/8→1/2] has been in use for years and is durable.
It's also good for extraction and accuracy.
Highly recommended!
View detail
It is easy to arrange a price at a low price.
It is easy to arrange a price at a low price. View detail
Some weight reduction
Purchased for Socket expansion.
Neither possible nor impossible.
The Gold model has been replaced or somewhat lightened.
View detail
It's not on the road a lot, but it's there when you need it.
If you want to buy a Single Item, you should buy a Quantity.:Purchased in Sets. However, there are some that do not come into play. But it is good to have it because it is necessary to have it when you need it. View detail
Required for certain locations of use
Bolt, depending on the part of the Nut to be worked on (e.g., covered by the exterior of the Scooter, etc.), it may not be possible to work without the Extension bar.
I have about three of them, long, medium and short.
If I can't reach it even with a long length, I combine medium and short lengths to make it even longer. It is self-responsibility.
View detail
Easy to use
It is used to tighten Stud bolts on new Parts and to loosen them from old Parts.
Since it is a KTC, it is convenient for accurate and reliable work.
View detail