Reviews
Right bottom? Screw hole is small.
The basic screw is M8 standard, but the screw hole under the right side is too small to accommodate the m8 bolt.
Note that it cannot be installed without extending it yourself.
View detail
Fits: HONDA CB400SF, HONDA CB400 SF Ver.S -98, HONDA CB400 SF Ver.R -98, HONDA CB400SF
Shorter than OEM and unusable.
Same length as OEM, but shorter and less useful View detail
OEM same etc.?
Handlebar side is covered with scratches, even though it is a visible part. View detail
Fits: YAMAHA SR400, YAMAHA SR400 88-00 Barnett accelerator holder
It didn't fit.
Does not fit the '00 2 SR400. Disappointed as I seem to have thrown away time and Gold. View detail
Fits: SUZUKI DR-Z400SM, SUZUKI DR-Z400S, SUZUKI DR-Z400 SM, SUZUKI DR-Z400 S, SUZUKI DR-Z400SM, SUZUKI DR-Z400S, SUZUKI DR-Z400 SM, SUZUKI DR-Z400 S
Although the object for DR-Z was purchased, the die length of the metal fittings (banana) attached to the axel side was different, and the degree of setting angle had bent. It is safer for deleting by a file grinder etc. to have needed to be processed
Although the object for DR-Z was purchased, the die length of the metal fittings (banana) attached to the axel side was different, and the degree of setting angle had bent.
It is safer for deleting by a file grinder etc. to have needed to be processed, and to purchase an original manufacturer's product, since it cannot attach as it is.
View detail
Fits: その他 For medium to large displacement millimeter (22.2mm) handles only.
Don't buy it
It was blubbery and completely unusable
Left was somewhat loose
The Throttle side was scantily clad and unusable
It immediately went to the trash
View detail
Adjustment Adjuster is less than half of OEM
Adjustment Adjuster is not available because the width of the adjuster is only half as wide as it should be
It was not available
In addition, the Manufacturer also reports the current situation from inquiry to the Adjuster's range I inquired about the OEM same or more, but ignored it
ALCAN hands, I'm disappointed in you!
View detail
Less than half of the OEM LengthAdjuster
Bore up for Adjuster, less than half of OEM LengthAdjuster Clutch will not break when used with a reinforced clutch
Loosely, I'm no use to you
View detail
It's not working!
It's not bad in form and appearance, but it's not as bad as the Bracket and The joints on the Mirror are loose, not just from vibrations, but from the wind, making it completely useless View detail
Fits: KAWASAKI Zephyr 750RS, KAWASAKI Zephyr 750, KAWASAKI Zephyr 750RS, KAWASAKI Zephyr 750
If it restricts to the viewpoint of conformity, it will be below brand-name parts. We cannot recommend you at all. A photograph is in the state which grasped the clutch. A portion without the screw thread at the tip of a mouthpiece is long, an
If it restricts to the viewpoint of conformity, it will be below brand-name parts.
We cannot recommend you at all.
A photograph is in the state which grasped the clutch.
A portion without the screw thread at the tip of a mouthpiece is long, and the dust cover of a rubber becomes narrow touch (it removed).
Moreover, a mouthpiece is long, and Tyco and since it is near, a folding angle will be attached to a wire.
The nylon of the circumference of Tyco has jumped out in the place run about 50 km after exchange.
Details are careless considering the elegance only for a vehicle type.
Since it is not quite satisfactory, it will exchange for brand-name parts.
View detail
Fits: SUZUKI DR-Z400SM, SUZUKI DR-Z400S, SUZUKI DR-Z400 SM, SUZUKI DR-Z400 S, SUZUKI DR-Z400SM, SUZUKI DR-Z400S, SUZUKI DR-Z400 SM, SUZUKI DR-Z400 S
Although DR-Z 400S was purchased, it not being needed for a throttle holder as it is, the metal fittings (banana) by the side of an axel throttle being too long, and the degree of setting angle having bent, and deleting with a grinder file etc. needed to
Although DR-Z 400S was purchased, it not being needed for a throttle holder as it is, the metal fittings (banana) by the side of an axel throttle being too long, and the degree of setting angle having bent, and deleting with a grinder file etc. needed to be processed.
Accuracy is past low however cheap it may be.
View detail