Reviews
oil cooler
About quality and texture The quality is good without oil spilling out About the feeling of use be of satisfactory quality Products to buy together SHIFT UP Aluminum Banjo Bolt M10/P1.25 Installed Together Difficulty of installation be as easy as pie Cost performance and comparison with other products The price is very good because it is a set of two About shipping and packaging It took a week and the packaging is excellent Any concerns, cautions, or advice when purchasing The price is better than anything else and the quality is excellent View detail
Also in Universal Product
Installed on TakegawaSpecial clutch cover for APE.
I thought about using a universal product, but since I had prepared an oil cooler made by Takegawa, I decided to purchase the product in question anyway.
Naturally, there were no problems with quality or fitting, and the installation process was smooth.
However, I have heard Small ear that color fading occurs after long-term use, so I am concerned about that.
It would be better if other colors could be selected if possible.
View detail
Stainless Steel
I have a SteelBanjo bolt from OEM, but I decided to go with Stainless Steel because of its appearance. I have had some experience with aluminum bolts that have been broken off in my old Torque. View detail
Stainless black
I am installing Stainless Steel, Black with matching pitches along with brembo installation. I would appreciate it if the price is lower. View detail
Cheap!
Titaniumium Bolt is available at a very low price!
Will buy again!
View detail
brembo
I bought this product because it is compatible with the Brembo master and Pitch.
It's not bad for the price.
View detail
exchange
In conjunction with the replacement of the caliper, we replaced it with a brembo compatible one.
The color of the corners peeled off when tightening, and since it's aluminum, you have to be careful not to overtighten.
View detail
Black
We installed black brake hose to match the black brake hose.
The color is simple and I like the color, though it is not noticeable.
View detail
I replaced it with Brake hose.
The quality was satisfactory without any problems.
However, I felt the price was a bit expensive.
I also bought the ↓ Banjo adapter with it.
https://www.webike.net/sd/4465941/
View detail
Brake hose replacement
I bought this stainless black to replace the Buildaline brake hose with stainless black and to connect to the Brembo caliper.
It's pricier than Aluminum … but I had to do it to unify the two. It looks nice and I like it.
View detail
ActiveBanjo bolt
I didn't see the color you were looking for!
They had it here and I bought it immediately.
Very good with a wide range of products!
View detail
The classic Banjo bolt
[How is it used?
NISSIN Brake master on ApriliaRS4 125 (https://www.webike.net/sd/1448239/) It was used to install the
I chose this product because it came up first when I looked up M10×P1.25 Banjo bolt in order of popularity.
Was the one you received as per Image?
There was a Red color setting, so I chose Red because I wanted to change it.
The multiple photos made me feel comfortable with my purchase. The one I received was exactly as pictured.
How was your experience with it?
It's no surprise, but it's not a bad performance for a Banjo bolt at all.
However, I don't know if my tool is too delicate or not. The paint on the corner came off....
To prevent fluid leakage, it is necessary to apply the torque firmly, so it is cheaper to use a proper tool.
[Products compared, etc.].
We compared it with other Manufacturer's Banjo bolt.
The price is similar, but I chose this product because it had the Red color setting and the evaluation of the impression was good.
I also had a sense of security because it was produced by a famous manufacturer called Active.
【Review】
The Banjo bolt can be used with confidence, and while it's inexpensive at 550 yen, it comes in many colors, so you have a lot of choices.
It's not so much that this product is bad, it's more that the tool is a bit lickable, so use a good tool.
View detail
It would be better if the length of the Bolt was also mentioned.
I bought this to install on my brembo rear caliper.
Pitch of brembo is 1.0mm, Hose and Fitting is the same swage, but when you install it, it may be bottomed out Limit, so you may need to adjust it with Washer.
View detail
StainlessBlack
I bought this Stainless Steel Black to replace the brake hose and unify it with Black.
It looks good, but I wish Washer was also Black, but I guess I can't help considering the Sealability Material.
I wish the price was a little lower.
View detail
Black color unification.
I bought it to unify with Black color.
Stainless Steel、Black、Quantity:When I bought the set, the pitch is different for the connection to brembo, because it is OEM Caliper compatible.
I had no choice but to purchase an additional Single Item for installation.
Washer, Silver stands out? No, but it can't be helped.
I hope Washer is also black because it is unified by black.
Well, I like the look and feel of it, but the price is …
I wish it was cheaper.
View detail
To match the Caliper color
I bought this to match my Brembo caliper black.
It's Stainless Steel, Black and looks good, but it's a decent price point for 1 pc.
View detail
Required for the old Crab caliper?
Installed on brembo old Crab caliper.
With the Caliper installed, the Bleeder Bolt is in a position where there is no way to turn it, so it's nice to have a product like this.
This allows you to replace the Fluid without removing the Caliper.
(You have to remove it to bleed air.)
The screw part is too long to fit on the OEM Banjo.
Two Washer on top and bottom (Total Quantity):(1 Set of 4pcs.) I used it.
View detail
Fits: HARLEY-DAVIDSON SPORTSTERFamily
For Repair.
Because Banjo bolt was dead, I replaced it. View detail
With the Hose replacement!
I installed it on MBK's sander, FranceYamaha's Max star125.
I also replaced the Banjo adapter along with it.
There are two types of Banjo, Goodridge Type and Earls Type, so if you don't replace these two types together, you'll end up with two different types.
Because the position of the hole shifts when it becomes so, because it affects Large to Touch of Brake, when changing Banjo system, I recommend exchange together when it changes Banjo system.
View detail
For MONKEYNISSIN!
Because it was the previous Bolt OEM Black, I changed all around the Brake hose. I bought and installed the same manufacturer as the Caliper side. View detail