Reviews
Fits: SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI Address V125G, SUZUKI Address V125G, SUZUKI Address V125G, SUZUKI Address V125G, SUZUKI Address V125G, SUZUKI Address V125G, SUZUKI Address V125 Limited, SUZUKI Address V125 Limited, SUZUKI Address V125 Limited, SUZUKI Address V125 Limited, SUZUKI Address V125S
Size is Exactly but
I ordered this to replace an Air cleanerFilter that was falling apart due to hydrolysis without my knowledge.
I wasn't sure how much filter oil (sold separately) to apply, so I applied the oil as I usually do on off-road motorcycles, but it seemed to be too much, and air cleaner oil spit out from the silencer for a while.
There is no way to go wrong with the installation.
View detail
Stainless bolt
Exhaust System fixing parts are rust-resistant Material:Changed to Stainless Steel.
This makes it rust-resistant and looks good.
View detail
Fits: HONDA PCX125, HONDA SHMODE, HONDA PCX150, HONDA PCX150, HONDA PCX125, HONDA AIR LADE125, HONDA Click125I
Air filter replacement
The product was full of dust and considering the application, I will still go with OEM Parts next time. View detail
I replace it every 20,000 km.
Reached 20,000 km since the last replacement. I bought this one again after the last time because it is the lowest price among the Net purchases according to my own research. I bought this one again, but this time the area of the filter was a little smaller than the previous one, which may be due to cost reduction. The installation was smooth and the precision of the others was good. View detail
KN Planning Fuel Hose
I am satisfied that this Size can be used by OEMs without any problems
The 6MM is a little too large for me, so this is the best size for me.
View detail
It's neither good nor bad
Ordinary Sponge type Air Filter
However, the price is lower than OEM parts, and since it is a dedicated product, it comes on properly without any defects.
View detail
Fits: HONDA MONKEY, HONDA SUPER CUB 50, HONDA LITTLE CUB, HONDA NSR50, HONDA NSR80, HONDA NS-1, HONDA NS50F, HONDA MBX50, HONDA CRM50, HONDA CRM80, HONDA MONKEY, HONDA GORILLA, HONDA Monkey Baja, HONDA MONKEY R, HONDA MONKEY RT, HONDA DAX50, HONDA DAX70, HONDA JAZZ, HONDA MAGNA50, HONDA CHALY 50
CUB press 50 AA01 Fi No fit ….
The Bolt was in a different position than the one originally attached.
Since the suppression plate is not included, it cannot be installed if the screw position does not match that of the installed Sprocket.
I'm still not sure if it's a product defect or a non-conformity.
View detail
May be easy to loosen.
I bought it because it is a Pressure Resistant, Oil Resistant Hose.
Leather mesh inevitably tends to unravel at the edges.
Well, that is acceptable.
The problem is that the inside Hose might be easy to loosen.
I used Oil Resistant Hose from KIJIMA or DAYTONA without Clamp and it never came loose.
I wonder if that is Minus.
View detail
difficult (e.g. customer, guest, child)
I bought this because it is so easy to use.
But after the first replacement, Wire was torn off.
I don't know if I put too much effort into it or if it's a trick...
I reported it to webike and they were able to replace it.
I will try again at my next Tire replacement!
So I'll give it a rating of 3 for now.
View detail
Fits: HONDA GROM, HONDA GROM, HONDA MSX125SF, HONDA MSX125, HONDA MSX125SF, HONDA MSX125
Chosen to match the situation.
This is the second replacement at 36,000 km.
I was hesitant to try the high flow type, which is more expensive but has better inhalation efficiency and removes garbages, etc., but in the end I chose the NORMAL paper filter.
The reason.
● Removing the Filter cover is quite a hassle (the method of removing the Horn, which is in the way, made the work progress).
● If you have removed the Cover, replacing it is faster and more convenient than cleaning it.
● Since it's a Touring Main, don't we need to be particularly concerned about intake efficiency, etc.?
And so on.
If you want to accelerate quickly in city driving, etc., you can use the High flow type I had chosen the
View detail
Fits: HONDA SUPER CUB 50, HONDA XLR250, HONDA XLR250, HONDA MONKEY, HONDA VARIE, HONDA DREAM50, HONDA DAX, HONDA SUPER CUB 90, HONDA SPACY80, HONDA SPACY80, HONDA SPACY50, HONDA GIORNO CREA, HONDA NY50, HONDA GORILLA
cheap
[How is it used?
To replace Exhaust System
How was your experience with it?
No problem No exhaust leakage
How did it compare to other products?
[Points to note]
It takes patience to peel off old Gasket.
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
View detail
Good cosmetics, but the quality is not as good as the price.
OEM has a texture like ShopTowel, KN has a texture like a vacuum cleaner paper pack.
Compared to OEM, the wire diameter of WireMesh on the reverse side is very thin and I am concerned that it may be damaged by vibration or corrosion during driving.
It is safer to use OEM Product, especially if you ride in the rain.
View detail
Fits: YAMAHA 7PSJOG, YAMAHA JOG, YAMAHA JOG, YAMAHA APRIO, YAMAHA APRIO, YAMAHA VINO, YAMAHA VINO
Expectations for corresponding products
I have received a response from Manufacturer, so I am adding this.
The defect was confirmed and returned Gold response.
It does not seem to be structurally designed to cause operational problems depending on the car model, so I am sure that this will be addressed when the product is next released.
I am attaching a photo for your reference.
View detail
PCX Air cleaner (Other Brand Product) for Repair
I am using a commercially available air cleaner for PCX on my ADV150.
Purchased for Repair.
Ignore the detailed dimensions as it was originally designed for the PCX and has been diverted to the ADV150.
However, I would like to mention one point of caution.
I couldn't tell because it's not in the picture, but it's only used for 90° bending.
I bought it but one side is twisted.
The twist could not be determined from the photo.
(Section is not vertical, about 85° and about 5° Up)
Please be careful when judging from the photo alone (although it can be used with some ingenuity).
View detail
Can use
Convenient to use for a wide range of corresponding Size for tightening of Hose.
It can be used with confidence because it can be tightened securely and there is no worry about liquid leakage.
It does not rust easily and can be used for a long time.
View detail
PVAccelerator cable
I used it on my '93 NA12A EPO50.
Because Throttle Wire and Oil pump wire are divided into two halves in the middle, it is difficult to make Wire by oneself, so I really wanted to use EPO50 OEM Parts, but it seems to be discontinued, so I had no choice but to use it.
I thought that Throttle and Oil pump could be turned at the same time with this because it was delivered and it was two-way, and I was relieved, but the Pitch of the carburetor side of the Throttle Wire of the photograph did not match and it was unavoidable. I assembled it.
And now, since the part is for TS50 HUSTLER, it is too long for EPO50, so I thought what to do, and I had to choose whether I should turn it around or cut it. After fitting the Oil pump wire and Throttle wire, I turned the bottom of Seat, and put Handlebar to Quantity:Pair (for Left and Right) I assembled it so that the pulling condition would not be bad by cutting it into
I was able to integrate it for now.
Then I started the engine and Idling was good and Axel opening and closing was good, but it looked a little worse.
Now you can shop at EPO50 again.
The result is not so bad, but if you want to imitate my work, please do it at your own risk.
View detail
Fits: HONDA BENLY50AA03, HONDA BENLY110JA09, HONDA LEAD110
The screw hole position is out of alignment with the OEM Product.
LEAD110 It was purchased with the mileage of 10,000 km, and Cleaner did not Check especially because it was said that it had been maintained.
I bought the Belt and Air Cleaner before replacing the Belt at almost 20,000km.
You have to remove the lid around the Rear Footpeg to open the Air cleaner, otherwise you can't turn the screw.
When I took it off, it was dirty, so I decided to replace it without cleaning it.
When the OEM Product is removed and this product is inserted, all of the screw holes underneath are only about half full.
I couldn't see it, but I just tightened it up.
I've driven about 300km and don't seem to have any problems.
View detail
Installed on gsf1200
Note the heat near the Engine.
Curled …
I didn't even get a Paper-type stinker.
It was good, though.
View detail
Fits: YAMAHA XMAX 250, YAMAHA XMAX 300, YAMAHA XMAX300, YAMAHA XMAX300
If they're going to claim OEM compatibility, they should make it so it fits properly.
I bought this one because it's a high flow type, but unlike the OEM, it doesn't fit properly. It was supposed to be a 5 minute job, but it took quite a while. If you want to be OEM compatible, you need to calculate the dimensions properly. View detail
Rubber is hard.
Fuel Hose has deteriorated and has been replaced.
Made of KevlarMesh?
Therefore, even if the R (R) of the Hose placement is bent a little too steeply, it will still function without collapsing in the Hose.
It's solid for that and is stiff and painful to finger when inserting it into the Fuel Cock.
View detail