KN Planning Motorcycle Reviews

Filter

Write a review and get Webike Points!

Reviews

D-TRACKER KN Planning Clear all

AluminumBillet master cylinder cap[DCR]Type-3

KN Planning

04 Mar 2024

AluminumBillet master cylinder cap[DCR]Type-3

Fits: HONDA NS-1, HONDA NSR50, HONDA NSR80, HONDA glom, HONDA FORZA250, HONDA CB125R, HONDA PCX125, HONDA PCX125, HONDA PCX150, HONDA FTR223, HONDA CB223S, HONDA CBR250R, HONDA CB250F, HONDA CBR250RR, HONDA VTR, HONDA VTR-F, HONDA CBR400R, HONDA CB400F, HONDA 400X, HONDA FAZE

Japanese Webike user

1/5

Don't leak.

Fluid will smear.
Mr. Manufacturer says there is no problem.
Diaphragm Plate should be present.
When I replaced it with DAYTONA, it didn't leak.
Is it Large sturdy if I get a new Diagram Flum?
But I'm not sure since I can't leak at the moment. View detail

KN Planning

14 Jun 2023

CNCMaster cylinder cap

Fits: HONDA CB125R, HONDA CB223S, HONDA CB250F, HONDA PCX125, HONDA PCX150, HONDA VTR-F, YAMAHA Helmet in JOG, YAMAHA XG250 TRICKER, YAMAHA SEROW250, YAMAHA SEROW225, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA GRAND AXIS, YAMAHA AXIS 90, YAMAHA XT250X, YAMAHA WR250, YAMAHA TW200, YAMAHA TW225, YAMAHA JOG90

Japanese Webike user

5/5

Recommendation to dress-up around Handlebar

[How is it used?
Installed on a PCX125JF56. the brake master cylinder cap had deteriorated considerably and was very dirty, so I decided to buy this product which can dress-up the cap.
Was the one you received as per Image?
I am very satisfied with the product, the texture and appearance are better than I expected.
Was the installation difficult?
It's easy, just remove the OEM brake master cylinder cap and put it in the same position. I used the supplied bolt to secure it in place.
How was your experience with it?
I am glad I changed it because it is a One Point around the Handlebar and the Tension goes up every time I drive. It is a little Custom, but I think the quality is very good for this price.
[Included Parts:were they on?
It contains an attached fixing Bolt.
The OEM bolt can be removed with a Phillips screwdriver, but I think the supplied special bolt is hexagonal.
[Was there anything that disappointed you?

Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer View detail

KN Planning

11 Jun 2023

[UmaRacing]Oil Breather Attachment A

Fits: HONDA FORZA, YAMAHA Cygnus X, YAMAHA Tricity155, HONDA Rebel300, HONDA CBR500R, HONDA CB500X, HONDA CB500F, HONDA CB300R, HONDA CB150R, YAMAHA MAJESTYS, YAMAHA BirdCITY125125, YAMAHA AxisZ, YAMAHA YZ450FX, YAMAHA YZ450F, YAMAHA YZ250X, YAMAHA YZ250FX, YAMAHA YZ250F, YAMAHA XV125SVIRAGO, YAMAHA XT225YSP, YAMAHA XT225WE

Japanese Webike user

4/5

One-touch detachable is convenient

It is standard practice to attach a Breather Hose 650mm 6mm Diameter to relieve pressure in the Crankcase,
It is common for the Hose and Breather cap to be directly connected.
The heat from the engine may harden the hose and cause the hose to come off the cap.
When replacing the oil, you can remove it with a push switch, which is convenient for the Large change.
However, the Push Switch will not come off if you press it too hard!
Press all the way down and back up a little to release it.
Sealing of the detachable part is not a problem. View detail

KN Planning

20 Apr 2023

AluminumBillet master cylinder cap[DCR]Type-3

Japanese Webike user

3/5

"cool

Cool, but the O-ring is thick and deforms when tightened.
Oil oozes, although it is not clear if that is the reason or not. View detail

KN Planning

09 Apr 2023

AluminumBillet master cylinder cap[DCR]Type-3

Japanese Webike user

4/5

I like the colored GuardCover.

Install the diaphragm so that it does not bite, but this is not particularly difficult. Since the installation is changed from a cross screw to a hexagonal screw, be sure to install with the proper torque so as not to overtighten.
I was a little concerned about the fact that it says "Made in Taiwan" and "Parenthesis" on the lid.
I have been using it for over a month now and have had no problems with it. View detail

KN Planning

10 Mar 2023

[UmaRacing]Oil Breather Attachment A

Fits: HONDA FORZA, YAMAHA Cygnus X, YAMAHA YZ450F, YAMAHA YZ250X, YAMAHA YZ250FX, YAMAHA YZ250F, YAMAHA XV125SVIRAGO, YAMAHA XT225YSP, YAMAHA XT225WE, YAMAHA XT225W, YAMAHA XT225S, YAMAHA XT225, YAMAHA XSR900, YAMAHA WR450F, YAMAHA WR250X, YAMAHA WR250R, YAMAHA TZR50R, YAMAHA TZR50, HONDA APE 50, HONDA APE 100

Japanese Webike user

4/5

Convenient to detach!

Breather Hose 650mm 6mm Diameter was attached directly to the Filler capAttachment, but as the hose deteriorated due to heat
I bought this one because it is hardened and LARGE weird to pull out.
Uma Recing's is good because the Hose and Filler section can be removed with One-touch.
However, the detachable Switch is not a full press, but a half press (?). It is like a half-press (?).
The filler part is aluminum, so it is not so much of a concern, but the nozzle of the hose section is plastic, so deterioration due to heat damage is a concern.
Still, I wonder if it is Universal because you can choose the angle of Nozzles. View detail

KN Planning

01 Mar 2023

CNC ฝาครอบกระปุกน้ำมันเบรค

Fits: HONDA CB125R, HONDA CB223S, HONDA CB250F, HONDA PCX125, HONDA PCX150, HONDA VTR-F, YAMAHA XG250 TRICKER, YAMAHA Helmet in JOG, YAMAHA SEROW250, YAMAHA SEROW225, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA GRAND AXIS, YAMAHA XT250X, YAMAHA AXIS 90, YAMAHA WR250, YAMAHA TW225, YAMAHA TW200, YAMAHA BW'S125

โป้ง

5/5

ตอนนี้ได้รับแล้ว งานcnc สวยงามมากรอไม่นานถือว่าไวมากๆ สั่งมาหลายรอบแล้ว สินค้าตรงตามสั่งทุกครั้ง ไม่เคยมีชิ้นไหนชำรุด หรือ เสียหาย สวยงามตามรูปใส่แล้วดูดีมาก ราคาถูกกว่าที่อื่นเยอะเลย โดยรวมถูกใจมากๆ เดี๋ยวสั่งของเรื่อยๆๆแน่นอนครับ View detail

KN Planning

26 Nov 2022

[UmaRacing]Oil Breather Attachment A

Japanese Webike user

5/5

I have been waiting for a product like this.

Before, I had to remove the hose every time I changed the oil, which was very troublesome.
This product is very easy to use because the Hose can be removed with One-touch.
Thank you, KN Planning. View detail

KN Planning

05 Nov 2022

[UmaRacing]Oil Breather Attachment A

Japanese Webike user

4/5

Oil replacement is easier.

[How is it used?
I was using a Mesh hose Breather kit and had to remove the hose every time I changed the oil, which was a bit odd, so I replaced it with this one-touch type.

Was the one you received as per Image?
The Hose fixing part was plus ticky than I expected.

Was the installation difficult?
The mounting base is slightly large, with a screw diameter of 19mm, and since it is used in conjunction with a cell motor, there is interference with the fitting, so it is quite limited.

How was your experience with it?
Clearance is the limit and one-touch attachment/detachment requires hang.
So far it is working fine, but I am concerned about its durability.

[Included Parts:were they on?
There is nothing else, it is a simple form with the product inside the Package.

[Was there anything that disappointed you?
The hose attachment part is plastic and may crack if it is tightened too much.
I am concerned about how well it will hold up to use over time.

▼ The Pipe at 45°C inclination was the Limit for use with the Cell Motor, so 90°C might have been a better choice. View detail

Billet Aluminum Master Cylinder Cap [DCR] Type 3

KN Planning

16 Sep 2022

Billet Aluminum Master Cylinder Cap [DCR] Type 3

Fits: HONDA FORZA250, HONDA CB125R, HONDA PCX125, HONDA PCX150, HONDA FTR223, HONDA CB223S, HONDA CBR250R, HONDA CB250F, HONDA VTR-F, HONDA GROM, HONDA NSR80, HONDA NSR50, HONDA NS-1, KAWASAKI D Tracker, KAWASAKI NINJA250R, KAWASAKI KSR110, KAWASAKI KSR-2, KAWASAKI KSR-1, KAWASAKI KLX300, KAWASAKI KLX250

Japanese Webike user

5/5

PetitAttachment Good cost performance

I think this is a great product for a little pre-Attachment.
The work can be easily done by simply installing Screw.
I put it on in a way that matches the color of the BIKE I ride. View detail

KN Planning

04 Sep 2022

Billet Aluminum Master Cylinder Cap [DCR] Type 3

Japanese Webike user

5/5

PetitCustom with good cost performance

Basically I like NORMAL, but as a PetitCustom it's inexpensive and a little Fashion!
It's easy to work with, just replace Screw with Hexagonal Wrench.
Highly recommended! View detail

KN Planning

03 Nov 2021

Diaphragm Throttle Valve

Fits: その他 Keihin genuine, その他 Keihin genuine, KAWASAKI D tracker, KAWASAKI GPZ1000RX, KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI KLX250, KAWASAKI ZRX1100, KAWASAKI ZRX1100-II, KAWASAKI ZRX1200, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI Estrella., KAWASAKI Zephyr 1100, KAWASAKI Zephyr 1100RS, KAWASAKI D tracker, KAWASAKI GPZ1000RX, KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI KLX250

Japanese Webike user

3/5

Improve Response

Throttle response has been improved. View detail

KN Planning

02 Oct 2021

[UmaRacing] Oil Breather Attachment A

Fits: HONDA FORZA, YAMAHA Cygnus X, YAMAHA YZ450FX, YAMAHA YZ450F, YAMAHA XT225YSP, YAMAHA XT225WE, YAMAHA XT225W, YAMAHA XT225S, YAMAHA XT225, YAMAHA XSR900, YAMAHA WR450F, YAMAHA WR250X, YAMAHA WR250R, YAMAHA TW225E, YAMAHA TW200E, YAMAHA TW200, YAMAHA TRACER900GT, YAMAHA TRACER900, YAMAHA TMAX530DX, YAMAHA TMAX530DSX

NO NAME

5/5

KN Planning [UmaRacing] Oil Breather Attachment A

The KN Planning [UmaRacing] Oil Breather it's a big help to my zoomer engine to cool down even in a long ride. It is highly recomended that you use a KN oil breather for your bike. View detail

KN Planning

04 Jan 2021

[UmaRacing]Oil Breather Attachment A

Japanese Webike user

4/5

Does it make it easier to take off?

I was going to use it for other vehicle diversions, but it was unexpectedly too tall to use. I'm going to use it for something else soon. The product is well made and has a good texture, but it is hard to put on and take off at first. If it is used, it will become easy, but.... By the way, there should be a lot of car models that can be used unexpectedly because Screw Pitch is Size that can be used for NORMALCase of MONKEY system. View detail

KN Planning

05 Nov 2020

Diaphragm Throttle Valve

Japanese Webike user

4/5

Good product

All in all, a very good product! 。 But my personal impressions are 'Ah! This is how it came to be!' It's as bad as it sounds. 。 (Emphasis & rarr;) Personally!
The vacuum valve, diaphragm and slide valve are all in one piece, but the slide valve is made of resin and is very light. 。 Probably because of its lightness, but it doesn't feel good in operation. 。 It's dull, it's sloppy, it's... ・ Especially the return.
It went from feeling like SpanSpan to feeling like a schooner....
Well, I'm getting used to it. View detail

KN Planning

29 Feb 2020

Diaphragm Throttle Valve

Japan User(translated)

4/5

This is good!

Here are my thoughts after using it
It used to be a one TEMPO13 late Throttle luck, but after the replacement Response is now much better than before:It may be called Valve of Plastic, but the Engine is smooth and blows instantly I think it is easy to ride Large
It is thought that it is more than worth replacing even if there is no visible damage to the Diaphragm The other thing is durability The other thing is durability View detail

KN Planning

28 Feb 2020

Diaphragm Throttle Valve

Japan User(translated)

3/5

It's good, right?

Somehow, I started to hold my breath in the straight slalom and sometimes I couldn't run well
I check the diaphragm, but it's not torn and it looks normal I put a new Diaphragm in the DF200 DJEBEL at the DF200 DJEBEL Radically It got better and I decided to install it
It's a lot of money to replace a stone with an OEM (1pc. approx. 10,000 yen) And this time, it's not even torn, so it takes courage, but for the price Trying something new And I TRIED to do it
Replacement can be done without putting the carburetor down, as the Diaphragm is just a little smaller How strong is Large? But I was able to install it safely I was worried about the engine to be installed because the shape of the engine is completely different from what it looks like Response is better and I am glad I replaced it View detail

KN Planning

30 Nov 2019

CNCMaster cylinder cap

Fits: HONDA CB125R, HONDA CB223S, HONDA CB250F, HONDA PCX125, HONDA PCX150, HONDA VTR-F, HONDA NSR80, HONDA NS-1, HONDA NSR50, HONDA FTR223, HONDA CBR400R, HONDA FORZA250, HONDA CBR250RR, HONDA CBR250R, HONDA CB400F, HONDA 400X, YAMAHA Helmet in JOG, YAMAHA XG250 TRICKER, YAMAHA SEROW250, YAMAHA CYGNUS X

Japan User(translated)

5/5

The planning is good for a variety of Parts I'd like to see a little more price … if possible! But you can rest assured that it is a reliable manufacturer View detail