Reviews
Fits: HONDA DIO, HONDA SUPER DIO, HONDA DIO FIT, HONDA LIVE DIO, HONDA SMART DIO, HONDA CREA SCOOPY, HONDA ZOOMER
Nice quality front fork
This machined aluminum front fork works fantastic on a Honda NPS50. They are of good quality and look nice. Do better than the original front fork. -------------------------------------------------- -------- This edited aluminum fork is fantastic on a Honda NPS50. Are of good quality and look nice. Do better than the original fork. Powered by Google Translator View detail
Fits: YAMAHA NMAX155, YAMAHA NMAX, YAMAHA NMAX155, YAMAHA NMAX
The feeling of shifting gears has changed quite a bit.
The Belt was replaced because it had traveled 18,000 km since the last Belt replacement. When we looked at the removed Belt, we found that it had not worn down to the limit of use, but the side angles were worn and attached.
I was worried about how the shifting would feel after installation, but I got the impression that the shifting became smoother, which was a good impression. However, I had the impression that the Engine RPMs dropped a little when shifting throughout the entire range, and the maximum speed dropped. (Tears)
I need to re-set with Weight Roller.
View detail
Fits: YAMAHA VINO(2Cycle), YAMAHA SUPER JOGZ, YAMAHA SUPER JOGZ, YAMAHA SUPER JOG ZR, YAMAHA JOG POCHE, YAMAHA JOG APRIO Type 2, YAMAHA JOG (2Cycle), YAMAHA APRIO, YAMAHA APRIO
scratch
Carbon paint peeling
without Logo
Are you inspecting?
View detail
Prepare just in case
We prepared just in case this was the first time we had to replace a Tire. View detail
Used for Monkey disk conversion
Each part was well made and the plating glue was good.
The Motorcycle Handlebar area has been tightened.
View detail
Fits: YAMAHA JOG (2Cycle), YAMAHA Remote controller jog, YAMAHA JOG, YAMAHA JOGDELUXE, YAMAHA Axis Treat, YAMAHA Remote controller jog, YAMAHA Remote controller jog, YAMAHA Remote controller jog, YAMAHA Remote controller jog, YAMAHA JOG (2Cycle), YAMAHA JOG, YAMAHA JOGDELUXE, YAMAHA JOG (2Cycle), YAMAHA JOG (2Cycle), YAMAHA JOG (2Cycle)
It's like OEM, and the price is very low.
The last 2-stroke JOG instead of a foot Remote controller jog I purchased this product because one of the blinker lenses was broken at that time. I purchased this product because one of the blinker lenses was cracked at that time.
OEM parts are also available, but the price is more than three times different, so we have to settle for cheap products.
No modification is required for installation, and the venue is about 98% the same as NORMAL. If you look strictly at the BALI, there are some things such as the presence or absence of BALI, but there are no obstacles.
The color difference from the OEM was the same as the OEM for a quick look. The one that needed to be replaced was the one side, but this product is Quantity:Pair (for Left and Right) Therefore, the Quantity:Pair (for Left and Right) We also exchanged with
I can spare the NORMAL for the one that is available!
I want to make sure I don't fall and Repeat.
View detail
![Reinforced Center Spring Middle Type [Medium]](https://img.webike-cdn.net/catalogue/images/31791/12151649_566fc6017084c_TS.jpg)
Fits: SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI Address V125S, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125
Excellent spring for increased torque
Fits: SUZUKI Address V100, SUZUKI Address V100
OEM's with Stages for acceleration modification.
As a precaution for installation, …Crank is an Opposite Thread Screw and the length of the Spline is limited, so there is a possibility of crushing it if it is tightened too much.
Grease is applied to the WR, but it is too little, so I applied additional grease. The Plus screw on the back cover is hard, but it loosens easily with the Impact Driver.
The PRESS processing on the back cover is rough in some areas and requires a compromise by the user.
The performance is more than sufficient, and although it may not be as good as the High Speed Pulley, it accelerates linearly with the Axel without any staggered acceleration.
To take advantage of the High Speed Pulley, it is necessary to consider the driven side as well, so if you are assuming that you are going to install it by itself, I think you will not be dissatisfied with this Pulley kit.
The weight of the attached wr is also a good feeling. I think it could be a little lighter for a young girl.
View detail
stage 6 mirrors
item received as described and well packed. received on time as well. will order more in the future stage6 mirrors are one of the most soughts mirror for small CC scooters such as namx xmax aerox... View detail
Cheap and affordable_OEM alternative
Something cheaper than OEM." I was looking for a Motorcycle supply store with the motto of
Although there are variants for Custom Ordinary." is not surprising.
I'm glad I found it on webike!
This is a great price for the front and rear parts and Screws included.
View detail
Custom
Recommended for those who do not want to put CALSeal directly on the License Plate! View detail
Fits: YAMAHA SMAX, YAMAHA SMAX, YAMAHA FORCE 155, YAMAHA Majesty S, YAMAHA Majesty S, YAMAHA BW'S R, YAMAHA BW'S 125, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X
All the OEM Parts you need are included.
It is better than ordering by parts Single Item, because it contains the parts you need. View detail
Fits: YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA CYGNUS X, YAMAHA CYGNUS X
CYGNUS-X Taiwan 5th stage is finally fully LED♪
[How is it used?
Touring and mainly city driving, with some night driving.
We had changed OEMTail to Smoked lens, and now the Rear blinker has become LED Blinker with this product.
The front blinkers were previously LEDs, so they were upgraded to front and rear LEDs.
Was the one you received as per Image?
Quantity:Pair (for Left and Right) The two blinkers are also wiring processed, so there is no need to replace the blinker relay when converting LEDs!
Double-sided tape is also included for easy installation.
Was the installation difficult?
In Taiwan 5th period, Tail is LED and Blinker is ValveLamp.
Valve is a member of the [Color] Clear, with OrangeCover attached with Screw, removed and installed.
A single screw in the middle and double-sided tape on the SIDE hold it firmly in place, so it will not rattle due to vibration.
How was your experience with it?
A sharp, LED-specific glow.
The sense of luxury has been improved.
The number of balls also looks good for rearward visibility.
The lens is used with a smoked lens and is clearly visible even in bright light.
I feel that the blinking lights are more vivid, and I feel that safety is improved when using the Blinker or Hazard lamps.
[Included Parts:were they on?
Two screws are provided for fixing.
There is no Instruction Manual, but just remove and install. It is easy to install.
View detail
KN Planning Fuel Hose
I am satisfied that this Size can be used by OEMs without any problems
The 6MM is a little too large for me, so this is the best size for me.
View detail
Fitting is outstanding!
The fitting is good and I am satisfied with Large! View detail
Fits: HONDA Claire's Coupe AF55, HONDA Claire's Coupe AF55
Wrinkle is noticeable.
The entire pull will be Wrinkle. View detail
Fits: HONDA Super DIO, HONDA Super DIO SR, HONDA Super DIOZX, HONDA Super DIO, HONDA XR Baja, HONDA DIO, HONDA DIO SP, HONDA DIO SR, HONDA G-dash, HONDA DJ1-RR, HONDA standup tact, HONDA Tact S, HONDA Johno., HONDA Lead 50, HONDA Joker 50, HONDA Broad 50, HONDA Cabina 50
Is the cast metal workmanship in line with the price?
Although it claims to be for introductory use, it does not come with an Instruction Manualetc.
The object seems to be a Cylinder dug for 49.9cc.
There was also a BALI removal in Cylinder.
The cooling fins? The cooling fin has a crack, or perhaps it did not flow into the mold properly, so I think it is a reasonable product.
On the intake side, etc., where no cutting was done, a powder-like substance fell out when the casting surface was textured and rubbed. Casting sand residue?
Recommendation is to clean it up once and then use it.
View detail
Fits: SUZUKI Address V100, SUZUKI Address V100
It could be used for OEM Product.
Could be used for OEM; not recommended for vehicles with Power out. View detail
YSS better absorber
About quality and texture: SUPPERB quality absorber than factory About the feeling of use: VERY stable when riding Products to buy together: FOLLOW the preference wrench Difficulty of installation: USE profesional workshop Cost performance and comparison with other products: WORTH money to buy About shipping and packaging: WELL pack good with box Any concerns, cautions, or advice when purchasing: THIS spring bigger than original View detail
with Rubber so it can be used for Seat cover or reupholstery.
[How is it used?
Seat of LITTLE CUB, which was given to us and had been neglected for a long period of time, was exposed to UV rays and had some tears. Let's reupholster it honestly." I wandered around Webike's site and came across this product.
The fabric is thin, but the OEM is also thin, so I have a faint hope that it will last a long time as long as it is kept out of the UV rays in the garage or body coverretc. when not being ridden.
How was your experience with it?
I am very satisfied with the large cover, as it has improved the comfort to the point that it would be rude to compare it to the aging OEMSeat Cover.
How did it compare to other products?
There are some inexpensive Seat Covers on the market, but I could not find a color tone that I liked, and color custom orders were too expensive, so I was wandering around Webike's site when I came across this product. Seat Grips. The stability of the event is irreplaceable.
[Points to note]
In my case, as I mentioned above. Seat cover. The assumption is that it is being used as a For re-covering Seat fabric, not as a
1. To remove the old Seat Cover, remove the Seat from the car body (the Seat can be removed by removing the two Bolts at the tip) and then unscrew the Bracket (Bracket plastic) that is fastened to the base behind the Seat, one by one, in a humble manner.
Remove the old skin and check the damage to Seat's sponge, and correct it if necessary.
3. Put the new Seat Cover on the front and back using a Tucker (a device similar to a large-mesh Stapler).:Pair (for Left and Right) (The front part is difficult to fasten with a standard tucker, so in some cases, a small wooden screw is used to fasten it.)
4. Put it back on the car body and you are done.
Other items that would be helpful
【Included Parts:presence or absence】.
One brief instruction sheet is included in the Seat Fabric Body.
If you are new to this, it may be difficult to understand, so please use each video Site. Motorcycle Seat Replacement Please search in etc.
[ITEMS TO BUY TOGETHER
Slotted screwdrivers and radio pliersetc. are helpful when removing old Seat Covers.
When attaching a new Seat Cover, you will need a Tucker & Staple to proceed with the work itself.
[Opinions and requests to Manufacturer
I would be very happy if there were more color variations, just a typical color pattern would be nice.
View detail